Computer numerical controller machinist jobs in Alexandria, VA

At Aurora Flight Sciences, we design, build, and fly advanced aircraft and enabling technologies from concept to reality. We are searching for a talented and self-motivated CNC Machine Operator to help us create the future of flight. Responsibilities will include but not be limited to the following: Responsibilities * Machining work via work orders, engineering drawings, materials, specifications, reference planes, locations of surfaces, interpreting geometric dimensions and tolerances (GD&T). * Plan and expedites orders for stock and verifies receipt. * Set up machine, including zero and reference points; setting tool registers, offsets, cutter compensation; calculating requirements, including basic math, geometry, and trigonometry; proving part program. Make proper installations and adjustments. * Measure positions with first-run part, and sampling of work pieces; adhering to international standards. * Maintain specifications by observing drilling, grooving, and cutting, including turning, facing, knurling and thread chasing operations; taking measurements; detecting malfunctions. * Troubleshooting processes; adjusting and reprogramming controls; sharpening and replacing worn tools; adhering to quality assurance procedures and processes. * Perform preventive maintenance requirements - follows manufacturer's instructions; troubleshoots malfunctions. * Maintain continuity among work shifts by documenting and communicating actions, irregularities, and needs in designated production and quality logs. * Follow engineering planning, and accurately fill out and complete work orders. * Support company Foreign Object Damage (FOD) Prevention Program. * Successfully completes training as required to maintain efficiency on the job. * Compliance with good housekeeping, quality, FOD, and safety procedures. * Support other Aurora Flight Sciences sites as required. * Performs other tasks as required by site leadership. Minimum Requirements * Education/experience typically acquired through basic education (e.g. high school diploma/GED). * Proficient in the use of computers and equipment utilizing computer technology in the fabrication of aircraft parts. * Be teachable and open minded. * Highly motivated. * Willing to learn and share knowledge. * Attention to Detail. * Exercise good judgement. * Knowledge of geometric tolerances is required. * Must be a US Person. Preferred Requirements * Related experience or an equivalent combination of education and experience (i.e., apprenticeship or trade school). * Ability to program machine, including zero and reference points; setting tool registers, offsets, compensation, and conditional switches; calculating requirements, including basic math, geometry, and trigonometry; proving part program. Make proper installations and adjustments. * Manual machining training / experience. * Ability to interpret complex engineering drawings, which utilize ASME, Y 14.5 M. * Conceptual skills; Process Improvement. * Experienced in FAA manufacture and associated paperwork. * Controls and Instrumentation. * Supply Management; Inventory Control. * Tooling; Coordination. Physical Requirements * Ability to work in a manufacturing environment and wear proper PPE. * Lift and transport objects up to 35 pounds; consistently stand, stoop, crawl, bend, crouch, climb, and kneel. * Work onsite in Manassas, VA. Salary Range (Annualized USD) * Minimum Range: $40,000.00 to $72,000.00 * Maximum Range: $48,000.00 to $85,000.00

We are seeking skilled Machinists capable of running manual and CNC lathes and mills to join a team of high-performing scientists, engineers, and technicians at our facility in Sterling, VA. **Responsibilities** + Set up, operate, and monitor CNC machines, including mills, lathes, and grinders, to produce parts and products. + Interpret technical drawings, blueprints, and work orders to determine machining operations and dimensions. + Load and edit CNC programs as required to ensure the production of parts to specifications, troubleshoot and optimize programs for efficiency. + Choose and install appropriate tools, fixtures, and gauges for machining processes. + Verify the conformity and quality of finished parts. + Perform inspections using precision measuring instruments such as calipers, micrometers, and CMMs to ensure parts meet strict quality standards. + Identify opportunities for process improvements, including optimizing machining time, tool life, and part quality. + Operate manual mills and lathes. + Perform regular machine maintenance and cleaning. + Other duties as assigned. **Essential Skills** + Experience with CNC machines, CNC lathes, and CNC equipment. + Proficiency in tool setup and reading and interpreting technical drawings. + 2+ years of related experience in machining. + Experience with CNC and manual lathe and mill operations. + Ability to interpret drawings according to ASME Y14.5-2009 standards. + Capability to inspect parts for dimensional compliance and machining quality. **Work Environment** This role requires working in a machine shop environment, often exposed to loud noises, moving machinery, and potential hazards. Appropriate personal protective equipment (PPE) will be provided. The position may require working in shifts depending on production schedules. Candidates must have the ability to lift and maneuver up to 50 lbs. and perform repetitive movements. The role also requires the ability to operate multiple machines at one time. **Job Type & Location** This is a Permanent position based out of Dulles, VA. **Pay and Benefits** The pay range for this position is $60000.00 - $85000.00/yr. Benefits information provided if an offer is made **Workplace Type** This is a fully onsite position in Dulles,VA. **Application Deadline** This position is anticipated to close on Dec 23, 2025. **About Aerotek:** We know that finding work is hard, and finding meaningful work is harder. Aerotek connects 180,000+ light industrial and skilled trades workers with 14,000+ employers each year, helping our workers navigate an evolving labor market and find jobs that meets their goals, skills and interests. Since 1983, we have provided a variety of career opportunities across North American industry - from short-term assignments at Fortune 500 companies where you can build your skills, to long-term opportunities where you can play a vital role solving for companies' construction, manufacturing and maintenance challenges. Our 1,500+ experienced recruiters across 250+ offices work relentlessly to put our workforce in a position to thrive. Let us rise to meet your challenges and put our people-are everything spirit to the test as your career continues to grow. Aerotek offers weekly pay, employee benefits including medical, dental & vision, life insurance, health advocacy and employee assistance programs, a 401(k) plan, and employee discounts. The company is an equal opportunity employer and will consider all applications without regards to race, sex, age, color, religion, national origin, veteran status, disability, sexual orientation, gender identity, genetic information or any characteristic protected by law.

Job Category: Service Contract Act Time Type: Full time Minimum Clearance Required to Start: Secret Employee Type: Regular Percentage of Travel Required: None Type of Travel: None * * * **What You'll Get to Do:** CACI is seeking a Junior CNC Machinist with a minimum of 1 to 3 years' experience. **More about this role:** + Ability to determine and perform appropriate set up of CNC Vertical machining centers for programs provided by CAM programmers + Ability to design and build fixtures preferred + Knowledge of G and M codes with ability to program at the control to build fixtures and edit CAM generated programs + Ability to select appropriate cutters and tool holders + Ability to set-up and operate the full range of machine tools found in a well-equipped prototype development shop + Ability to maintain dimensional accuracy, to specified tolerances that may be less than +/-.001", during machining processes, through the use of measuring instruments (e.g. vernier calipers, inside/outside & depth micrometers, gage blocks, surface and height gages, and dial indicators). + Ability to work independently with minimal supervision + Ability to read blue prints and mechanical drawings + Knowledge of Mil-Spec and GD&T specifications + Ability to work from verbal instructions and sketches + Ability to perform machine shop math and trigonometry + CAM and Solid modeling CAD experience a plus + Ability to lift and maneuver objects weighing 80 pounds + Adhere to safety protocols + Ability to operate a forklift a plus **You'll Bring These Qualifications:** + Successful completion of machinist apprenticeship + Journeyman CNC Machinist qualification + Trade School certificate + High School diploma or equivalent + DoD Secret Clearance or capability to be granted DoD Secret Clearance + Knowledge of Shop, Facility and Division Safety Policies and requirements **Working Conditions:** + Contractor will frequently work inside and outside of buildings. S/he will work in cold weather. S/he may be working in the hot sun. S/he will work in environments where ventilation or respirators may be necessary. S/he must be safety minded about themselves and others. S/he will check tools and equipment, and see their capacities are not exceeded; and that tools are kept in a safe working condition. + Physical: (1) Lift up to 80 lbs. (2) Work in Industrial and Test Facility Environment including cranes, fork trucks and vehicle operations. + Hazardous Duty: Incumbent performs work in industrial settings where the potential for hazards exists. However, the use of engineering controls, materials substitution and personal protective equipment reduce or eliminate hazard exposure. Incumbent is regularly exposed to the hazard of: noise, electrical shock, wet surfaces, and climbing. The contractor will occasionally use hazardous materials e.g. various oils and solvents. The contractor is occasionally exposed to high work and confined space. This position is contingent on funding and may not be filled immediately. However, this position is representative of positions within CACI that are consistently available. Individuals who apply may also be considered for other positions at CACI. **________________________________________________________________________________________** **What You Can Expect:** **A culture of integrity.** At CACI, we place character and innovation at the center of everything we do. As a valued team member, you'll be part of a high-performing group dedicated to our customer's missions and driven by a higher purpose - to ensure the safety of our nation. **An environment of trust.** CACI values the unique contributions that every employee brings to our company and our customers - every day. You'll have the autonomy to take the time you need through a unique flexible time off benefit and have access to robust learning resources to make your ambitions a reality. **A focus on continuous growth.** Together, we will advance our nation's most critical missions, build on our lengthy track record of business success, and find opportunities to break new ground - in your career and in our legacy. **Your potential is limitless.** So is ours. Learn more about CACI here. (************************************************ **________________________________________________________________________________________** **Pay Range:** This posting is for a position covered by the Service Contract Labor Standards (SCA). The pay and benefits provided for this position will meet or exceed the minimum required amounts detailed in the wage determination issued by the Department of Labor and made applicable to this position, as incorporated into CACI's government contract for the work location. **Minimum Req** **uired Hourly Wage:** $31.20 There are a host of other factors that can influence final salary including, but not limited to, geographical location, relevant prior work experience, specific skills and competencies, education, and certifications. Our employees value the flexibility at CACI that allows them to balance quality work and their personal lives. We offer competitive compensation, benefits and learning and development opportunities. Our broad and competitive mix of benefits options is designed to support and protect employees and their families. At CACI, you will receive comprehensive benefits such as; healthcare, wellness, financial, retirement, family support, continuing education, and time off benefits. Learn more here (***************************************************** . _CACI is_ _an Equal Opportunity Employer._ _All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, pregnancy, sexual orientation, age, national origin, disability, status as a protected veteran, or any_ _other protected characteristic._

Job DescriptionSalary: $29.50-42.00 Internal Code: CNC5 Reports to: Operations Manager MATSYS, Inc. is seeking a CNC Machinist to join its team of high-performing scientists, engineers, and technicians at its Sterling, VA facility. The CNC Machinist is responsible for setting up and operating CNC machines to produce high-quality precision components according to engineering drawings and specifications. This role requires hands-on machining expertise, strong attention to detail, and the ability to maintain tooling, equipment, and process documentation to meet tight tolerances, deadlines, and customer requirements, often in support of defense projects. If you are looking to join a rapidly growing company that offers a dynamic, fast-paced, solution-driven work environment, MATSYS is the place for you! This position is expected to be primarily assigned to our research and development facility (6 am-2:30 pm, Monday Friday), but the candidate should be flexible and willing to cross-train in our production environment (6 am-4:30 pm, Monday Thursday), as well. The successful candidate will be hired as a Machinist II or III based on experience and skillset. Description Set up and and operate CNC mills and lathes to produce precision parts Interpret engineering blueprints, technical drawings, and work orders to ensure parts meet tolerances and quality standards Perform machine offsets, tool changes, and adjustments as necessary Inspect parts using calipers, micrometers, and gauges Troubleshoot machining programs and processes Maintain machine tools, cutting equipment, and workstations in a clean and safe condition Complete documentation such as job travelers, inspection reports, and nonconformance records Collaborate with engineers and others to improve machining processes and implement lean manufacturing practices Follow all company compliance requirements Other duties as assigned Required Must be a U.S. citizen due to government contract requirements High School diploma or equivalent 3+ years of experience operating CNC machines in a precision (metal part) manufacturing environment (aerospace or defense experience desirable) Proficiency with precision measuring instruments (micrometers, calipers, height gauges, bore gauges, etc.) Ability to read and interpret GD&T (Geometric Dimensioning & Tolerancing) Basic program editing experience Ability to follow standard operating procedures (SOPs) and safety guidelines Working Conditions: Standing, walking, lifting/maneuvering up to 50 lbs. Frequent exposure to powders, dust, lubricants, and manufacturing equipment Use of PPE such as gloves, masks, safety shoes, and protective eyewear. Preferred 2-year degree, technical certification, apprenticeship or equivalent Experience with 5-axis mills Experience operating wire EDM machines Experience programming with CAD/CAM software (MasterCam preferred) Familiarity with ISO 9001 quality systems Competencies Work Execution & Excellence: efficient planning & quality execution, ability to meet deliverables & deadlines, drive towards excellence Communication & Team Impact: effective & quality communication ability, ability to effectively share technical information, as well as accountability and a team player commitment Technical Expertise & Development: continual learning and commitment to cross-training, strong hands-on mechanical skills Autonomy, Judgment & Decision-Making: Sound judgment and planning ability, risk assessment skills, creativity & critical problem-solving Commitment to MATSYS core values and ideals: Safety: Safety is at the forefront of our decision-making. We hold each other responsible to ensure the health and safety of our team at all times. Quality: We stake our reputation on our impeccable standards. We provide the utmost quality in everything that we do and deliver above expectations, both as individuals and as a team. Integrity: We are accountable, transparent, and act with respect and in the best interests of our customers, communities, and employees. Teamwork: Good ideas come from everyone and great ideas come from us working together. Impact: We are responsive and effect positive and ground-breaking change, delivering excellence every step of the way. About MATSYS Inc. As a frontrunner in next-generation materials and manufacturing processes, MATSYS excels in developing advanced materials and manufacturing processes, setting itself apart through innovation and problem-solving. With a culture built on collaboration, transparency, and excellence, we prioritize client satisfaction through open communication and integrity, fostering enduring partnerships. Our teams diverse skills in material development, powder processing, and design fabrication enable us to deliver comprehensive solutions to complex problems. Our future vision includes expanding production capabilities, establishing strategic integrations with industry leaders, and driving continuous innovation and growth. MATSYS prides itself on its dynamic team, its ability to push boundaries and the commitment of its employees to excellence, innovation and teamwork. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex (male or female), national origin, age, disability, genetic information, protected veteran status, or any other characteristic protected by applicable law. Employment decisions are based solely on merit, qualifications, and business needsnever on protected characteristics. MATSYS uses E-Verify to verify right-to-work. MATSYS is a Drug-Free Workplace. Candidates are required to pass a pre-employment background investigation and drug test prior following receipt of a conditional job offer.

Company Profile Oceaneering Technologies (OTECH) develops, manufactures, and operates customized marine systems, shipboard equipment, subsea vehicles, and engineered solutions for commercial and U.S. military vessels. Oceaneering Aerospace and Defense Technologies (AdTech) delivers solutions that enable humans to work safely and effectively in harsh environments - from underwater to the outer reaches of space. Our innovative solutions support the development and application of practical, cost-effective systems that meet our customers' challenges - from routine to extreme. Our experience and expertise across multiple industries uniquely positions us as a leader in the government, space, and maritime services markets. Our products and services meet the rigorous demands of the complex environments in which they operate, delivering results without compromising safety or reliability. Oceaneering is a global provider of engineered services and products, primarily to the offshore energy industry. We develop products and services for use throughout the lifecycle of an offshore oilfield, from drilling to decommissioning. We operate the world's premier fleet of work class ROVs. Additionally, we are a leader in offshore oilfield maintenance services, umbilicals, subsea hardware, and tooling. We also use applied technology expertise to serve the defense, entertainment, material handling, aerospace, science, and renewable energy industries. Position Summary The First-Class CNC Machinist must be able to read and work from blue prints, as well as set up and operate conventional and CNC lathes and mills with minimal guidance. Must have ability to self-inspect all work. Should be able to work with CAD/CAM programming systems. Duties And Responsibilities ESSENTIAL • Able to set up CNC equipment (Lathes and/or Mills). Select proper cutting tools, optimize cutting process at machine, makes program edits at machine, and effectively produce quality parts in appropriate time. • Decipher information from blueprints. • Familiar with Mastercam programming or similar programming systems. • Design fixtures, tooling, and parts to meet machining requirements. • Measure and examine completed parts to ensure conformance to specifications using precision measuring instruments. • Perform routine maintenance and minor repairs on machine shop equipment. • Operate and rig material handling equipment (overhead cranes, gantries, forklifts). • May train and support entry level Machinists. • Additional duties as assigned. Qualifications REQUIRED • High school diploma or equivalent, or one to three years formal training (vocation or technical school), • Five years previous experience in a machine shop with CNC machine operation. • Must have own basic machinist's tools for machine setup and inspection. • Strong familiarity with Machine Shop Safety and OSHA requirements. • Ability to program, set up, and operate all conventional and CNC lathes and mills. • High proficiency in blueprint reading and machining techniques. • Knowledgeable in various CNC programming systems (Master Cam). • In depth knowledge in the operation of conventional and CNC machine shop equipment. Additional Information PAY, BENEFITS AND WORK SCHEDULE: We offer a comprehensive and competitive benefits package. Employee benefits vary by role, however, may include Health and Wellness, Mental Health, Retirement Savings, Life and Disability, Paid Maternity and Parental Leave, Paid Time Off, Tuition Reimbursement, and an Employee Assistance Program. Base pay rate for this position is $33.92 to $45.96. Equal Opportunity Employer All qualified candidates will receive consideration for all positions without regard to race, color, age, religion, sex (including pregnancy), sexual orientation, gender identity, national origin, veteran status, disability, genetic information, or other non-merit factors. How To Apply Regular full-time employees who apply will be considered along with external candidates. Employees with less than six months with their current position are not eligible to apply for job postings. Please discuss your interest in the position with your current manager/supervisor prior to submitting your completed application. It is highly recommended to apply through the PeopleSoft or Oceanet portals.

Advanced Mission Partners a wholly owned subsidiary of SSAI, seeks CNC Machinist. to help provide support to the procurement team. The CNC Machinist manufactures precisely engineered parts used to build instruments, machines and tools. Their duties include setting up equipment, operating equipment and inspecting finished parts. The position is located at the manufacturing facility in Lanham, Maryland. The responsibilities include: Responsibilities: Review samples, drawings or instructions to understand specifications of output Plan the sequence of necessary actions for the completion of a job Take measurements and mark material for cutting or shaping Select appropriate machines (e.g. lathes) and position or load material for a job Determine and program size of batches, speed of machine etc. Monitor machine while working to adjust the feed, maintain temperature and identify issues Check output to ensure consistency with specifications and report defects Keep records of approved and defective units or final products Perform routine machine maintenance and repair minor damages Required Qualifications: Proven experience and familiarity with Computer Numerical Control (CNC) software and machinery used for computer-aided manufacturing Experience in using and/or programming manual, semi-automated or automated tools and machines (lathes, grinders etc.) Ability to use precision tools (e.g. calipers) to take accurate measurements Knowledge of the properties of metal and other material Ability to read blueprints, schematics and manuals Math skills to take precise measurements and make calculations Demonstrated oral and written communication skills Analytical and problem-solving skills to develop effective manufacturing plans based on specifications Ability to move roughly 25 to 50 pounds and remain stationary throughout a shift Understanding of health and safety regulations to reduce the risk of workplace accidents Preferred Qualifications: Completion of vocational school training 10+ years' experience operating CNC machinery Supervisory experience. EEO/AA Veterans and Individuals with Disabilities Physical Requirements: While performing the duties of this job, the employee is regularly required to stand, walk, and use hands to touch, handle or feel objects, tools or controls. The employee frequently is required to talk and hear and occasionally required to reach with hands and arms and stoop, kneel, crouch, or crawl. Must regularly lift and/or move up to 10 pounds, and occasionally lift and/or move up to 25 pounds. Specific vision abilities required by this job include close vision, peripheral vision, depth perception and the ability to adjust focus.

In this role you will operate, clean, and maintain various machining equipment including lathes, mills, 3\-axis machines, 5\-axis machines and other equipment to make precise parts, ensure efficient operations, and achieve high utilization. At ADDMAN, you'll be part of a skilled and growing team serving the defense, space and commercial aerospace industries. This position is for B shift hours are 3pm\- 11pm. ESSENTIAL JOB FUNCTIONS: Always has safety first in mind when working at ADDMAN, uses all personal protective equipment as required. Ensures all equipment and forklifts are functioning per design and function. Shuts down equipment and stops operations in unsafe conditions, lockout\/tagout when necessary. Utilizes work instructions, set\-up sheets and method documents to correctly operate machines and inspect machined parts. Reads and interprets all drawings, including geometric dimensioning and tolerancing. Accurately reads and records information (i. e. material manufacture date, number of parts produced, and other criteria) that is critical to the production process. Follows instruction from a traveler\/router and machining procedures to perform the machining process. Operates various equipment and makes various parts to precise specifications utilizing knowledge of metal properties, set ups, layouts, and precision machining procedures. Ability to read and understand sketches, blueprints and thorough understanding of tools and proper use of fixtures. May set up, or learn to set up, and run CNC or manual machinery. Adjust controls to vary the depth of cut, RPM and rate of feed efficiently. Updates inventory systems for usage and scrap and prepares Material Tags for non\-conforming parts. Capable of following detailed manufacturing processes to produce high\-tolerance parts. Adheres to the AS9100 and ISO 9000 standards and complies with internal Quality Management System (QMS) standards. Utilizes various gauging equipment to ensure conformance to the engineering specifications and standards through the production run i.e. calipers, micrometers, gage pins height gages, dial indicators and precision scales. Maintains an accurate count and record production pieces and hours of production. Performs housekeeping and cleanup duties upon completion of assigned tasks. Actively participates in housekeeping and 5S efforts by maintaining an orderly, clean, and safe work area. Keeps equipment and product free of FOD, Foreign Object Debris. Promotes teamwork within the organization. Follows all Company Human Resources policies and process procedures. Performs other duties as assigned. Requirements ITAR REQUIREMENTS: This position is subject to the International Traffic in Arms Regulations (ITAR) which requires U.S. person citizenship status. Requirements Able to work in a dynamic environment with changing priorities to exceed customer expectations Works independently, strong work ethic, is self\-motivated and able to complete tasks with minimal supervision Ability to work on cross\-functional teams to support the core business, ensuring quality products are delivered on time Computer aptitude (Outlook, PowerPoint, Word and Excel) Ability to read, write, and communicate in the English language Must be a team player and willing to learn new skills and concepts QUALIFICATIONS: Previous experience in machining and with quality processes is desired Some exposure and experience with manufacturing \/CNC machining processes Understand continuous improvement or lean \/ six sigma principles Graduate of related two\-year vocational school program and three years related work experience and\/or training; or equivalent combination of education and experience Eligible to work in the United States without company sponsorship WORK ENVIRONMENT: The performance of this position will require exposure to the manufacturing areas where all areas require the use of personal protective equipment such as safety glasses, hearing protection, steel toe shops, and other mandatory safety equipment. For the most part, ambient temperatures with typical plant lighting and manufacturing equipment are present throughout the facility. PHYSICAL DEMANDS: Sit or stand as needed. Walking primarily on a level surface for periodic periods throughout the day. Reaching above shoulder height, below the waist, or lifting as required to reach documents or store materials throughout the workday. Proper lifting techniques required. Ability and comfortability to work in small confine spaces while following proper safety protocol. SAFETY AND POLICY PRACTICES: Each employee must be knowledgeable of standard safety policies and procedures and adhere to the same while supporting the goals and objectives of the organization and recognizing the Company's need to achieve its business objectives. Each employee is responsible for complying with company hazardous waste disposal procedures. AFFIRMATIVE ACTION: ADDMAN Engineering is proud to be an Equal Opportunity Employer of Minorities, Women, Protected Veterans, and Individuals with Disabilities. All terms and conditions of employment will be administered without regard to an individual's sex, gender identity, sexual orientation, race, color, religious creed, national origin, physical or mental disability, protected veteran status, or any other characteristic protected by applicable law. NOTE: This is intended to describe the general level of work being performed. This is not intended to be all\-inclusive. The duties of this position may change from time to time, and the employee may perform other related duties to meet the ongoing needs of the organization. ADDMAN Engineering reserves the right to add, delete or modify these duties and responsibilities at its discretion. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions of this position. Employment is at\-will, and nothing in this job description is intended to create or imply a contractual relationship or alter the at\-will status of the employee. "}}],"is Mobile":false,"iframe":"true","job Type":"Full time","apply Name":"Apply Now","zsoid":"667294733","FontFamily":"Verdana, Geneva, sans\-serif","job OtherDetails":[{"field Label":"Industry","uitype":2,"value":"Manufacturing"},{"field Label":"City","uitype":1,"value":"Glen Burnie"},{"field Label":"State\/Province","uitype":1,"value":"Maryland"},{"field Label":"Zip\/Postal Code","uitype":1,"value":"21060"},{"field Label":"Salary","uitype":1,"value":"23.00"}],"header Name":"CNC Machinist II\-B Shift","widget Id":"4**********0072311","awli IntegId":"urn:li:organization:18758749","is JobBoard":"false","user Id":"4**********1692017","attach Arr":[],"awli ApiKey":"86ezhi1yg2oktx","custom Template":"3","awli HashKey":"c21b16e3c8dbe9654eb55b1f04069e03d572626405c07f472ea90a39cdba9a8**********8097028c357acddf7e325374edf16ca 4013eb8708eaa9f0dbef6a35","is CandidateLoginEnabled":true,"job Id":"4**********5078885","FontSize":"12","google IndexUrl":"https:\/\/lucasjamestalent.zohorecruit.com\/recruit\/ViewJob.na?digest=Nyi9VFWIsbMXNaN0qju4ExnqFgCWB6snf.Rr8WJbtro\-&embedsource=Google","location":"Glen Burnie","embedsource":"CareerSite","indeed CallBackUrl":"https:\/\/recruit.zoho.com\/recruit\/JBApplyAuth.do","logo Id":"pcy573a2da6bcad414975813a806bd9435355"}

SUMMARY: A CNC Machinist is responsible for operating one or more types of computer numeric controlled production equipment. Selects appropriate settings and makes adjustments as necessary. Commitment to and support of the Company Core Values are key to success in this position. ESSENTIAL DUTIES AND RESPONSIBILITIES: Verify that material and paperwork for the job being performed is correct Plan machining in accordance with all blueprints and hard copy and electronic technical data and specifications, applying geometric dimensioning and tolerances as required Set-up mills by adjusting all necessary fixturing and machine attachments; setting and applying tool and machine reference points and offsets and calculating requirements using basic math, geometry, and trigonometry Check stock and load and unload the machine Create an in-process inspection report for each operation, as necessary, if one does not exist Identify non-conformance, if discovered, notify your supervisor so that it can be documented identified, dispositioned, and segregated from the remainder of the lot Verify that there are no chips on either the jaws/fixture or on the part/material to be machined. Load the part/material, verify that the part is properly seated in the fixture/jaws, snug against any stop pins prior to clamping or tightening of the jaws Identify discrepant material left in your work area, notify your supervisor so that it can be dispositioned and segregated. Follow all quality procedures, work instructions, and documents pertaining to your job and department. Identify any problems/issues while running an operation, notify the supervisor immediately Responsible for keeping the machine and the immediate area clean Monitor coolant levels Clean the chips from machine at the end of shift, or when the job is finished Verify that all company and personal inspection equipment and tools being used are in calibration. Adhere to all company safety policies including the use of eye and ear protection. Perform all functions of the job while adhering to established quality policies and procedures Uphold the company core values Other duties as assigned SUPERVISORY RESPONSIBILITIES: This position has no supervisory responsibilities. QUALIFICATIONS: To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Successful accomplishment of duties and responsibilities may require the following: Must be able to operate the various machines within the department with minimal instruction. Must be capable of reading drawings and be able to inspect the parts they are machining. Must be capable of working with minimal supervision. EDUCATION and/or EXPERIENCE: High school diploma or general education degree (GED); or 2 years experience; or equivalent combination of education and experience.0 LANGUAGE SKILLS: Ability to speak and understand basic safety and manufacturing instructions. MATHEMATICAL SKILLS: Ability to add and subtract two-digit numbers. Ability to multiply and divide with 10's and 100's. REASONING ABILITY Prioritize activities and work under pressures at all times. Comply with safety standard procedures Be able to differentiate between a symptom and a root of the problem Open to change and improvements Maintain clean and organized workspace CERTIFICATES, LICENSES, REGISTRATIONS: Authorization to work in the United States. To conform to U.S. export control regulations, you should be eligible for any required authorizations from the U.S. Government. PHYSICAL DEMANDS: The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand, walk, and hear. The employee frequently is required to use hands and fingers; handle, feel, and reach with hands and arms. The employee is occasionally required to sit; climb or balance; stoop, kneel, crouch, or crawl; and smell. The employee must frequently lift and/or move up to 50 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception, and ability to adjust focus. WORK ENVIRONMENT: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this position, the employee is regularly exposed to moving mechanical parts. The employee may be exposed to hot and/or cold work environment, chemicals, fumes or airborne particles, loud noises, risk of electrical shock and vibration low and high temperatures and/or other occupational hazards; personal protective equipment may be required. NOTE: This identifies the general nature and scope of work to be performed. Vitesse Systems, LLC. reserves the right to revise all or any part of this and to add or eliminate essential job functions at any time. Designation of any job duty as an essential function is not intended as an assurance or guarantee that a team member has any right to perform the job duty, except as required by Vitesse Systems, LLC. This job description is subject to change based on the needs of the position and/or the Company. Vitesse Systems, LLC performs work controlled by the International Traffic in Arms Regulations (ITAR) and Export Administration Regulations (EAR). These statutes require the protection of technical data and products. The regulations require that such data not be disclosed in written, oral, or visual form to any foreign national without prior export authorization from the Department of State. A foreign national is defined by the U.S. Government under EAR 734.2(b)(2)(ii) and 8 USC 110 (a)(20) as one who: Is not a United States citizen Is not lawfully admitted for permanent residence in the U.S. Does not have politically protected status (embassy, refugee, or asylum) Has dual U.S. / foreign citizenship Vitesse Systems, LLC. is an Equal Employment Opportunity / Affirmative Action (EEO/AA) Veterans / Disabled Employer

SUMMARY: A CNC Machinist is responsible for operating one or more types of computer numeric controlled production equipment. Selects appropriate settings and makes adjustments as necessary. Commitment to and support of the Company Core Values are key to success in this position. ESSENTIAL DUTIES AND RESPONSIBILITIES: Verify that material and paperwork for the job being performed is correct Plan machining in accordance with all blueprints and hard copy and electronic technical data and specifications, applying geometric dimensioning and tolerances as required Set-up mills by adjusting all necessary fixturing and machine attachments; setting and applying tool and machine reference points and offsets and calculating requirements using basic math, geometry, and trigonometry Check stock and load and unload the machine Create an in-process inspection report for each operation, as necessary, if one does not exist Identify non-conformance, if discovered, notify your supervisor so that it can be documented identified, dispositioned, and segregated from the remainder of the lot Verify that there are no chips on either the jaws/fixture or on the part/material to be machined. Load the part/material, verify that the part is properly seated in the fixture/jaws, snug against any stop pins prior to clamping or tightening of the jaws Identify discrepant material left in your work area, notify your supervisor so that it can be dispositioned and segregated. Follow all quality procedures, work instructions, and documents pertaining to your job and department. Identify any problems/issues while running an operation, notify the supervisor immediately Responsible for keeping the machine and the immediate area clean Monitor coolant levels Clean the chips from machine at the end of shift, or when the job is finished Verify that all company and personal inspection equipment and tools being used are in calibration.

Job DescriptionBenefits: 401(k) 401(k) matching Competitive salary Dental insurance Health insurance Paid time off Vision insurance Job Title: CNC Operator Location: King of Prussia, PA (On-Site, Full-Time) Responsibilities: Operate CNC fabrication machinery for cutting and finishing custom stone countertops and surfaces. Read shop drawings, templates, and layout specifications. Use hand tools and fabrication equipment with accuracy. Handle, stage, and move stone materials. Maintain high standards of quality and precision. Qualifications: CNC machine operation experience. Hand tool and saw operation skills. Forklift operation experience is a plus. Strong problem-solving skills and attention to detail. Prior experience in stone fabrication or construction preferred. Experience: 2 10 years Other Benefits: Overtime opportunities. Growth and advancement potential. Supportive, team-oriented environment. Stable workload with an established brand. This is a remote position.

About Us: BW Papersystems, part of the Barry-Wehmiller Group, builds capital equipment that transforms paper into products for consumers - every day, around the world. We offer innovative technologies, service and parts, and years of global experience in corrugating, finishing; slitting and packaging; stationery; bookbinding and security documents. Customers rely on our machines to produce and convert items such as corrugated boxes, folding cartons, passports, notebooks, copy paper, board, and coated and other specialty papers. For more information, visit bwpapersystems.com. Barry-Wehmiller is a diversified global supplier of engineering consulting and manufacturing technology for the packaging, corrugating, sheeting and paper-converting industries. By blending people-centric leadership with disciplined operational strategies and purpose-driven growth, Barry-Wehmiller has become a $3 billion organization with nearly 12,000 team members united by a common belief: to use the power of business to build a better world. Job Description: BW Papersystems is seeking a CNC Machinist to join our team! BW Papersystems is searching for a CNC Machinist that can perform a range of rough and finish turning, drilling, tapping, boring, facing, recessing, thread cutting and similar machining operations on a variety of shafts, housings heads, and parts of various ferrous and non-ferrous metals and alloys. In this role you will machine parts to specifications using manual and CNC machine tools such as mills, lathes, saws, and grinders. Key Responsibilities: * Select the appropriate tools, machines, and materials to be used in preparation of machinery work. * Perform a range of rough and finish turning, drilling, tapping, boring, facing, recessing, thread cutting and similar machining operations on a variety of shafts, housings, heads, and parts of various ferrous and non-ferrous metals and alloys. * Align and secure holding fixtures, cutting tools, attachments, accessories, and materials onto machines. * Use GD&T principles to interpret and analyze blueprints, schematics, and technical drawings to ensure accurate implementation of standard processes. * Use mathematical knowledge to calculate location and positioning of features. * Edit programs, set up, adjust, and operate basic machine tools, and many specialized or advanced machine tools to perform precision machining operations. * Monitor the feed and speed of machines during the machining process and perform quality control checks of critical features. * Measure, examine, and test completed units to detect defects and ensure conformance to specifications using precision instruments like micrometers, dial bore gauges, and calipers. * Maintain clean and orderly work areas and equipment, report and correct and unsafe work practices or conditions immediately. * Perform all work in accordance with established safety procedures. * Multi-task various duties throughout the day; maintain a positive attitude with versatility and flexibility. * Communicate and interact with various teams and teammates to solve problems independently. Basic Qualifications & Requirements: * High School Diploma or GED equivalent * 2+ years of experience working in a machine shop environment. The approximate pay range for this position is $23/HR - $30/HR. Please note that the pay range provided is a good faith estimate for the position at the time of posting. Final compensation may vary based on factors including but not limited to background, knowledge, skills, and abilities as well as geographic location of the position. #LI-JK2 At Barry-Wehmiller we recognize that people come with a wealth of experience and talent beyond just the technical requirements of a job. If your experience is close to what you see listed here, please still consider applying. We know that our differences often can bring about innovation, excellence and meaningful work-therefore, people from all backgrounds are encouraged to apply to our positions. Please let us know if you require reasonable accommodations during the interview process. Barry-Wehmiller is an equal opportunity employer. M/F/D/V This organization uses E-Verify. Applicants may be subject to pre-employment screening which may include drug screening, reference checks, employment verifications, background screening and/or skills assessments. Company: BW Papersystems

Now Hiring CNC Machine Operators - All Shifts Available (1st, 2nd & 3rd) | $1,000 Hiring Bonus! Are you ready to launch or grow your career in manufacturing? We're hiring CNC Machine Operators for all shifts and offering a $1,000 hiring bonus! Experience is preferred, but we're happy to train motivated candidates. Join a forward-thinking manufacturing team focused on quality, precision, and innovation. We offer career advancement opportunities, comprehensive benefits, and a supportive environment where your work truly matters. What You'll Do: Operate CNC machining and turning centers to produce precision components. Read and interpret part drawings and specifications. Perform inspections using micrometers, calipers, gauges, and other measuring tools. Maintain tolerances within +/- .05mm through offsets and minor tool changes. Load, inspect, assemble, and package parts per documented instructions and quality standards. Accurately complete production and inspection documentation. Support cross-training initiatives on various machines as needed. Follow all safety and quality procedures, and maintain a clean work area. What We Offer: $1,000 hiring bonus Weekly pay and competitive wages Shift premiums for 2nd and 3rd shifts 8-hour shifts with paid breaks Medical, dental, and vision insurance Health Savings Account (HSA) option Life insurance and short-term disability Paid vacation and holidays 401(k) with company match What We're Looking For: 6+ months of CNC machine operation experience (preferred) Familiarity with Fanuc controls on machines such as Mori Seiki, Okuma, or Hardinge Ability to lift heavy objects frequently and stand for an 8-hour shift Strong attention to detail and quality standards Dependability, self-motivation, and a collaborative attitude Good attendance and safety record Production Lead candidates should also have a 1-year technical certificate and experience in training and troubleshooting.

In this role you will operate, clean, and maintain various machining equipment including lathes, mills, 3-axis machines, 5-axis machines and other equipment to make precise parts, ensure efficient operations, and achieve high utilization. At ADDMAN, you'll be part of a skilled and growing team serving the defense, space and commercial aerospace industries. This position is for B shift hours are 3pm- 11pm. ESSENTIAL JOB FUNCTIONS: Always has safety first in mind when working at ADDMAN, uses all personal protective equipment as required. Ensures all equipment and forklifts are functioning per design and function. Shuts down equipment and stops operations in unsafe conditions, lockout/tagout when necessary. Utilizes work instructions, set-up sheets and method documents to correctly operate machines and inspect machined parts. Reads and interprets all drawings, including geometric dimensioning and tolerancing. Accurately reads and records information (i. e. material manufacture date, number of parts produced, and other criteria) that is critical to the production process. Follows instruction from a traveler/router and machining procedures to perform the machining process. Operates various equipment and makes various parts to precise specifications utilizing knowledge of metal properties, set ups, layouts, and precision machining procedures. Ability to read and understand sketches, blueprints and thorough understanding of tools and proper use of fixtures. May set up, or learn to set up, and run CNC or manual machinery. Adjust controls to vary the depth of cut, RPM and rate of feed efficiently. Updates inventory systems for usage and scrap and prepares Material Tags for non-conforming parts. Capable of following detailed manufacturing processes to produce high-tolerance parts. Adheres to the AS9100 and ISO 9000 standards and complies with internal Quality Management System (QMS) standards. Utilizes various gauging equipment to ensure conformance to the engineering specifications and standards through the production run i.e. calipers, micrometers, gage pins height gages, dial indicators and precision scales. Maintains an accurate count and record production pieces and hours of production. Performs housekeeping and cleanup duties upon completion of assigned tasks. Actively participates in housekeeping and 5S efforts by maintaining an orderly, clean, and safe work area. Keeps equipment and product free of FOD, Foreign Object Debris. Promotes teamwork within the organization. Follows all Company Human Resources policies and process procedures. Performs other duties as assigned. Requirements ITAR REQUIREMENTS: This position is subject to the International Traffic in Arms Regulations (ITAR) which requires U.S. person citizenship status. SKILL REQUIREMENTS: Able to work in a dynamic environment with changing priorities to exceed customer expectations Works independently, strong work ethic, is self-motivated and able to complete tasks with minimal supervision Ability to work on cross-functional teams to support the core business, ensuring quality products are delivered on time Computer aptitude (Outlook, PowerPoint, Word and Excel) Ability to read, write, and communicate in the English language Must be a team player and willing to learn new skills and concepts QUALIFICATIONS: Previous experience in machining and with quality processes is desired Some exposure and experience with manufacturing /CNC machining processes Understand continuous improvement or lean / six sigma principles Graduate of related two-year vocational school program and three years related work experience and/or training; or equivalent combination of education and experience Eligible to work in the United States without company sponsorship WORK ENVIRONMENT: The performance of this position will require exposure to the manufacturing areas where all areas require the use of personal protective equipment such as safety glasses, hearing protection, steel toe shops, and other mandatory safety equipment. For the most part, ambient temperatures with typical plant lighting and manufacturing equipment are present throughout the facility. PHYSICAL DEMANDS: Sit or stand as needed. Walking primarily on a level surface for periodic periods throughout the day. Reaching above shoulder height, below the waist, or lifting as required to reach documents or store materials throughout the workday. Proper lifting techniques required. Ability and comfortability to work in small confine spaces while following proper safety protocol. SAFETY AND POLICY PRACTICES: Each employee must be knowledgeable of standard safety policies and procedures and adhere to the same while supporting the goals and objectives of the organization and recognizing the Company's need to achieve its business objectives. Each employee is responsible for complying with company hazardous waste disposal procedures. AFFIRMATIVE ACTION: ADDMAN Engineering is proud to be an Equal Opportunity Employer of Minorities, Women, Protected Veterans, and Individuals with Disabilities. All terms and conditions of employment will be administered without regard to an individual's sex, gender identity, sexual orientation, race, color, religious creed, national origin, physical or mental disability, protected veteran status, or any other characteristic protected by applicable law. NOTE: This is intended to describe the general level of work being performed. This is not intended to be all-inclusive. The duties of this position may change from time to time, and the employee may perform other related duties to meet the ongoing needs of the organization. ADDMAN Engineering reserves the right to add, delete or modify these duties and responsibilities at its discretion. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions of this position. Employment is at-will, and nothing in this job description is intended to create or imply a contractual relationship or alter the at-will status of the employee. Salary Description $23 -$28 / Per hour

The TSUBAKI name is synonymous with excellence in quality, dependability and customer service. U.S. Tsubaki is a leading manufacturer and supplier of power transmission and motion control products. As a part of a vast, international network of corporate and industrial resources, Tsubaki offers its customers the finest state-of-the-art products available in the world and we strive to be the “Best Value” supplier in the industry. Essential Duties and Responsibilities: The essential duties and responsibilities of this job are included but not limited to this job description - other tasks may be assigned and expected to be performed. Interprets drawings to visualize final form of die, part or tool, and plans sequence of operations to achieve desired end result Works from prints, sketches, verbal or written instructions, or from existing part to be copied or fitted Lifts, positions, and secures parts to be machined on surface plate or worktable, using hoist, vises, v-blocks, or angle plates Sets up and operates machine tools such as CNC mills and lathes, manual mills and lathes, CNC and manual grinders, wire EDM, saw Plans the set up and operation of machine shop tools considering types of material, tolerances, types of cutting tools, coolants, lubricants, and machine tool feeds and speeds Programs mills and lathes using conversational programming and/or CAM by entering instructions including setting zero and reference points, tool registers, tool offsets, geometry of part, etc. Verifies dimensions, alignments, and clearances of finished parts, using measuring instruments such as CMM, calipers, micrometers, height gages, dial indicators, and gage blocks Fits and assembles jigs, fixtures, tools and dies, using wrenches, hammers, arbor or hydraulic presses Troubleshoots poor performing tools, identifying deficiencies and suggesting improvements Designs jigs, fixtures, or templates for use as work aides Inventories, requests, and investigates alternative cutting tools and shop supplies Promptly and accurately completes all required recordkeeping and inspections Performs routine machine maintenance as assigned Other tasks, projects and functions as assigned. Requirements: High school diploma or equivalent preferred; equivalent relevant experience may be considered Trade school or Apprenticeship program preferred Exhibits in-depth job knowledge and skills Adjusts machine feed and speed, change cutting tools, or adjust machine controls when automatic programming is not optimum Develop CNC machining processes by selecting the chucking device, cutting tools, tool arrangement, and cutting speeds and feeds with emphasis on standardization Create and maintain CNC programs to produce parts using CAD/CAM software. Experience utilizing GibbsCAM, MasterCAM, Fusion 360, Edgecam, Partmaker, or Esprit is a plus Thorough understanding of workholding, datums, sequence of operations, tool selection Can prioritize the work and coordinate with others Capable of fostering a team environment Self-motivated and can work with little supervision Thinks, plans, and responds quickly to unexpected events Able to multi-task in a fast-paced environment with changing priorities Active participant in troubleshooting and problem solving Capable of running multiple machines while they are in automatic cycles Basic Windows operating system navigation, Basic Microsoft Office Suite, CAM software experience preferred Math skills up to basic trigonometry (addition, subtraction, multiplication, division, finding an angle or tangent) Mechanical aptitude to understand how processes operate Technical skills and experience to solve complex problems and troubleshoot Analytical and critical thinking skills to foresee issues with designs or processes and come up with alternate solutions Attention to detail to ensure the highest level of precision in finished work Time management and having a sense of urgency for the jobs at hand Ability to work with others in a fast-paced manufacturing setting Learn more about U.S. Tsubaki at: U.S. Tsubaki offers: A competitive compensation package, including health benefits effective on date of hire, generous 401(k) match and profit sharing, education reimbursement, and annual bonus potential Paid time off (“PTO”) 90-day and 180-day performance reviews Shift differential pay for 2nd and 3rd shift Weekly bonus potential Paid training Weekly pay Shift: 4 days a week, 10 hours per day. Days: Monday - Thursday (standard schedule). Overtime may be required on Fridays/Saturdays according to business needs. The estimated salary range is meant to reflect an anticipated salary range for the position. We may pay more or less than of the anticipated range based upon market data and other factors, all of which are subject to change. Individual pay is based on location, skills and expertise, experience, and other relevant factors. Tsubaki is an Equal Opportunity Employer - Minorities/Females/Veterans/Disability PM21 PI73310c8b6b78-30***********7

Junior Machinist- 5 Axis CNCJob Category: Service Contract ActTime Type: Full time Minimum Clearance Required to Start: SecretEmployee Type: RegularPercentage of Travel Required: NoneType of Travel: None* * * CACI is looking for a Computer Numerical Control (CNC) Machinist for technical support at the Naval Surface Warfare Center Carderock Division (NSWCCD) Model Shop fabricating prototype naval component scale models for R&D testing. This employee will also serve as the subject matter expert on CNC programming and fabrication, and will advise shop management, supervisors, and planners on the difficulty, complexity and risks that may arise in fabrication of potentially complex parts. More About the Role Machine model components using CNC and manual mills and lathes. Program, setup, and operate 3-, 4-, or 5-axis CNC machines. Hand-finish parts as required, using contouring and polishing. Collaborate with design engineers, make recommendations and share best practices with machining approaches and materials as a subject matter expert (SME) on machining Read and interpret engineering drawings (CAD/CAM) and tolerancing schemes, including GD&T. You'll Bring These Qualifications High School Diploma or GED 1-5 years of experience with setting up, programming, editing and operating CNC milling and lathe machines Experience with machining metals (aluminum, stainless steel) and other materials Experience with design process and mechanical assembly. Must be able to read and interpret drawings and blueprints Must be able to obtain and maintain an DoD Secret Clearance Effective verbal and written communication in English Basic MS Windows skills Ability to perform basic mathematical computations Ability to apply concepts such as fractions, percentages, ratios, and proportions to practical situations PHYSICAL DEMANDS - Ability to move or transfer products with an overhead crane; Ability to lift 50 lbs. when required; While performing the duties of the job, the employee is regularly required to stand, walk, and reach with hands and arms; Specific vision abilities required by this job include close vision, distance vision, color vision, depth perception, and ability to adjust focus These Qualifications Would Be Nice to Have Active DoD Secret Clearance This position is contingent on funding and may not be filled immediately. However, this position is representative of positions within CACI that are consistently available. Individuals who apply may also be considered for other positions at CACI. ________________________________________________________________________________________ What You Can Expect: A culture of integrity. At CACI, we place character and innovation at the center of everything we do. As a valued team member, you'll be part of a high-performing group dedicated to our customer's missions and driven by a higher purpose - to ensure the safety of our nation. An environment of trust. CACI values the unique contributions that every employee brings to our company and our customers - every day. You'll have the autonomy to take the time you need through a unique flexible time off benefit and have access to robust learning resources to make your ambitions a reality. A focus on continuous growth. Together, we will advance our nation's most critical missions, build on our lengthy track record of business success, and find opportunities to break new ground - in your career and in our legacy. Your potential is limitless. So is ours. Learn more about CACI here. ________________________________________________________________________________________ Pay Range: This posting is for a position covered by the Service Contract Labor Standards (SCA). The pay and benefits provided for this position will meet or exceed the minimum required amounts detailed in the wage determination issued by the Department of Labor and made applicable to this position, as incorporated into CACI's government contract for the work location. Minimum Required Hourly Wage: $31.20 There are a host of other factors that can influence final salary including, but not limited to, geographical location, relevant prior work experience, specific skills and competencies, education, and certifications. Our employees value the flexibility at CACI that allows them to balance quality work and their personal lives. We offer competitive compensation, benefits and learning and development opportunities. Our broad and competitive mix of benefits options is designed to support and protect employees and their families. At CACI, you will receive comprehensive benefits such as; healthcare, wellness, financial, retirement, family support, continuing education, and time off benefits. Learn more here. CACI is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, pregnancy, sexual orientation, age, national origin, disability, status as a protected veteran, or any other protected characteristic.

SUMMARY: A CNC Machinist is responsible for operating one or more types of computer numeric controlled production equipment. Selects appropriate settings and makes adjustments as necessary. Commitment to and support of the Company Core Values are key to success in this position. ESSENTIAL DUTIES AND RESPONSIBILITIES: Verify that material and paperwork for the job being performed is correct Plan machining in accordance with all blueprints and hard copy and electronic technical data and specifications, applying geometric dimensioning and tolerances as required Set-up mills by adjusting all necessary fixturing and machine attachments; setting and applying tool and machine reference points and offsets and calculating requirements using basic math, geometry, and trigonometry Check stock and load and unload the machine Create an in-process inspection report for each operation, as necessary, if one does not exist Identify non-conformance, if discovered, notify your supervisor so that it can be documented identified, dispositioned, and segregated from the remainder of the lot Verify that there are no chips on either the jaws/fixture or on the part/material to be machined. Load the part/material, verify that the part is properly seated in the fixture/jaws, snug against any stop pins prior to clamping or tightening of the jaws Identify discrepant material left in your work area, notify your supervisor so that it can be dispositioned and segregated. Follow all quality procedures, work instructions, and documents pertaining to your job and department. Identify any problems/issues while running an operation, notify the supervisor immediately Responsible for keeping the machine and the immediate area clean Monitor coolant levels Clean the chips from machine at the end of shift, or when the job is finished Verify that all company and personal inspection equipment and tools being used are in calibration. Adhere to all company safety policies including the use of eye and ear protection. Perform all functions of the job while adhering to established quality policies and procedures Uphold the company core values Other duties as assigned SUPERVISORY RESPONSIBILITIES: This position has no supervisory responsibilities. QUALIFICATIONS: To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Successful accomplishment of duties and responsibilities may require the following: Must be able to operate the various machines within the department with minimal instruction. Must be capable of reading drawings and be able to inspect the parts they are machining. Must be capable of working with minimal supervision. EDUCATION and/or EXPERIENCE: High school diploma or general education degree (GED); or 2 years experience; or equivalent combination of education and experience.0 LANGUAGE SKILLS: Ability to speak and understand basic safety and manufacturing instructions. MATHEMATICAL SKILLS: Ability to add and subtract two-digit numbers. Ability to multiply and divide with 10's and 100's. REASONING ABILITY Prioritize activities and work under pressures at all times. Comply with safety standard procedures Be able to differentiate between a symptom and a root of the problem Open to change and improvements Maintain clean and organized workspace CERTIFICATES, LICENSES, REGISTRATIONS: Authorization to work in the United States. To conform to U.S. export control regulations, you should be eligible for any required authorizations from the U.S. Government. PHYSICAL DEMANDS: The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand, walk, and hear. The employee frequently is required to use hands and fingers; handle, feel, and reach with hands and arms. The employee is occasionally required to sit; climb or balance; stoop, kneel, crouch, or crawl; and smell. The employee must frequently lift and/or move up to 50 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception, and ability to adjust focus. WORK ENVIRONMENT: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this position, the employee is regularly exposed to moving mechanical parts. The employee may be exposed to hot and/or cold work environment, chemicals, fumes or airborne particles, loud noises, risk of electrical shock and vibration low and high temperatures and/or other occupational hazards; personal protective equipment may be required. NOTE: This identifies the general nature and scope of work to be performed. Vitesse Systems, LLC. reserves the right to revise all or any part of this and to add or eliminate essential job functions at any time. Designation of any job duty as an essential function is not intended as an assurance or guarantee that a team member has any right to perform the job duty, except as required by Vitesse Systems, LLC. This job description is subject to change based on the needs of the position and/or the Company. Vitesse Systems, LLC performs work controlled by the International Traffic in Arms Regulations (ITAR) and Export Administration Regulations (EAR). These statutes require the protection of technical data and products. The regulations require that such data not be disclosed in written, oral, or visual form to any foreign national without prior export authorization from the Department of State. A foreign national is defined by the U.S. Government under EAR 734.2(b)(2)(ii) and 8 USC 110 (a)(20) as one who: Is not a United States citizen Is not lawfully admitted for permanent residence in the U.S. Does not have politically protected status (embassy, refugee, or asylum) Has dual U.S. / foreign citizenship Vitesse Systems, LLC. is an Equal Employment Opportunity / Affirmative Action (EEO/AA) Veterans / Disabled Employer

Job DescriptionJob Responsibilities Operate CNC mills and/or lathes to produce precision parts according to work instructions. Load and unload raw materials and finished parts from machines. Monitor machine operation and make minor adjustments as needed to maintain part quality. Perform basic measurements using calipers, micrometers, and other inspection tools to ensure parts meet specifications. Read and interpret blueprints and Geometric Dimensioning & Tolerancing (GD&T) to verify part accuracy. Fill out in-process inspection documentation to ensure quality standards are met. Maintain a clean and organized work area. Follow all safety protocols and company procedures. Assist with basic machine maintenance, such as cleaning and lubrication. Qualifications & Requirements Previous experience operating CNC machines preferred, but willing to train motivated candidates. Ability to read and understand blueprints and GD&T. Strong attention to detail and commitment to quality. Ability to accurately complete in-process inspection documentation. Proficiency in using precision measuring instruments. Ability to lift up to 40 lbs and stand for extended periods throughout the shift. Willingness to learn and work as part of a team in a fast-paced environment. This is a remote position.

We are seeking an efficient and detail-oriented CNC Punch Operator responsible for setting up, operating, and maintaining CNC punch machines to manufacture precision metal parts and components. This role involves interpreting technical drawings, ensuring quality standards, and adhering to safety protocols. The ideal candidate will have a strong understanding of CNC machinery, attention to detail, and a commitment to producing high-quality products. **Job Responsibilities** + Use a computer to nest parts onto sheets. + Set up and calibrate CNC punch machines according to specifications and blueprints. + Load materials into the machine and ensure proper alignment for accurate punching. + Label parts and organize them onto carts. + Manage inventory of raw materials. + Communicate status of jobs and machines effectively to coworkers. + Perform routine checks and maintain machines, keeping proper levels of hydraulic fluid and greasing bearing surfaces regularly. + Inspect finished products to ensure they meet quality standards and specifications. + Handle raw materials. + Document part production. + Adhere to all safety protocols and procedures to maintain a safe working environment. + Other duties as assigned. **Additional Skills & Qualifications** + Technical certification or vocational training in CNC operations preferred. + Previous experience operating CNC punch machines or similar machinery is a plus. + Basic computer skills for machine programming and data entry. + Ability to navigate folder structures and keep files organized on a computer as well as with physical documents. + Ability to read and interpret technical drawings and blueprints. + Proficiency in using precision measurement tools and gauges. + Experience with CNC machine setup. + Familiarity with machining and calipers. + Previous experience as a CNC Machine Operator or in programming. **Apply to this posting directly.** **Job Type & Location** This is a Contract to Hire position based out of Hanover, MD. **Pay and Benefits** The pay range for this position is $25.00 - $30.00/hr. Eligibility requirements apply to some benefits and may depend on your job classification and length of employment. Benefits are subject to change and may be subject to specific elections, plan, or program terms. If eligible, the benefits available for this temporary role may include the following: - Medical, dental & vision - Critical Illness, Accident, and Hospital - 401(k) Retirement Plan - Pre-tax and Roth post-tax contributions available - Life Insurance (Voluntary Life & AD&D for the employee and dependents) - Short and long-term disability - Health Spending Account (HSA) - Transportation benefits - Employee Assistance Program - Time Off/Leave (PTO, Vacation or Sick Leave) **Workplace Type** This is a fully onsite position in Hanover,MD. **Application Deadline** This position is anticipated to close on Dec 17, 2025. **About Aerotek:** We know that finding work is hard, and finding meaningful work is harder. Aerotek connects 180,000+ light industrial and skilled trades workers with 14,000+ employers each year, helping our workers navigate an evolving labor market and find jobs that meets their goals, skills and interests. Since 1983, we have provided a variety of career opportunities across North American industry - from short-term assignments at Fortune 500 companies where you can build your skills, to long-term opportunities where you can play a vital role solving for companies' construction, manufacturing and maintenance challenges. Our 1,500+ experienced recruiters across 250+ offices work relentlessly to put our workforce in a position to thrive. Let us rise to meet your challenges and put our people-are everything spirit to the test as your career continues to grow. Aerotek offers weekly pay, employee benefits including medical, dental & vision, life insurance, health advocacy and employee assistance programs, a 401(k) plan, and employee discounts. The company is an equal opportunity employer and will consider all applications without regards to race, sex, age, color, religion, national origin, veteran status, disability, sexual orientation, gender identity, genetic information or any characteristic protected by law.

Job DescriptionGluer Machine Setup Operator About the job Day Shift and Night Shift Availability | Excellent Benefits | Climate Controlled Key Job Responsibilities: Provide instruction, direction, and support to the entire crew working on the assigned equipment. Educate less senior employees and train them to attain higher levels of achievement, up to and including operator. Set up automatic gluing machine, including feeder, score breakers, glue application systems, bar code readers, pressure rolls, and delivery, to operate at maximum speed and efficiency while providing superior quality. Knowledgeable of the raw materials, support materials, tools, and principles associated with folding carton gluing. Make necessary mechanical adjustments required to prepare all types of gluing equipment to glue specified manufacturing orders. Operate all types of gluers at maximum production speed, maximum utilization, and minimum waste. Perform feeding function and observe the machine to maintain operating efficiency and quality. Receive and interpret production orders and verbal orders. Ensure glued cartons meet all quality specifications for gluing characteristics and perform final inspection. Operate hand, fork, and clamp trucks as required. Operate quality control equipment as required and perform assigned Quality Assurance tasks. Maintain a constant supply of all raw materials, tools, and support items to ensure continuous operation of the equipment throughout the manufacturing run. Report causes for all machine downtime, reasons for not meeting planned productivity, and reasons for material waste. Ensure the work area and methods used are always safe and reasonably free from risk of health problems and injury, including proper handling of heavy items, repetitive movements, and hazardous materials. Maintain cleanliness and compliance with all regulations. Ensure proper tagging of each load for identification and report production quantity and quality by run sequence. Advise team facilitator and/or supervisor on the status of job supplies and materials. Complete daily time sheets and machine reports. Lubricate equipment, make minor repairs, and help in clean up. Advise supervisor of any need for major repairs or adjustments. Contribute to studies related to recommendations and/or decisions for purchasing additional buildings or equipment. Cooperate with management by performing any business duties necessary to effect accurate and efficient workflow. Train someone to serve as backup for this position and serve as backup for another position. Comply with all rules, regulations, and safety requirements. Perform other duties as assigned. Physical Requirements: Use hand tools Standing for the entire shift Bending, squatting, leaning, lifting Required Education: High School Diploma/GED Required Knowledge, Skills, and Abilities: Operate hand jack and hydraulic pallet jack Understand job jacket information Complete necessary paperwork Demonstrate mechanical aptitude necessary to be successful in the position Must be able to read, write, and speak English Preferred Qualifications: 1-3 years experience in a manufacturing/industrial environment Additional Information: Focused on solving difficult challenges with innovative packaging solutions that meet specific needs with a lean and sustainable approach.