Top Instrument And Electrical Technician Skills

Below we've compiled a list of the most important skills for an Instrument And Electrical Technician. We ranked the top skills based on the percentage of Instrument And Electrical Technician resumes they appeared on. For example, 9.8% of Instrument And Electrical Technician resumes contained Programmable Logic Controllers as a skill. Let's find out what skills an Instrument And Electrical Technician actually needs in order to be successful in the workplace.

The six most common skills found on Instrument And Electrical Technician resumes in 2020. Read below to see the full list.

1. Programmable Logic Controllers

high Demand
Here's how Programmable Logic Controllers is used in Instrument And Electrical Technician jobs:
  • Maintain all instrumentation, distributed control systems, programmable logic controllers and electrical equipment.
  • Worked on Allen-Bradley PLC 5 Programmable Logic Controllers diagnosing control problems on process equipment.
  • Operate the Allen Bradley PLC, SLC 5/04 CPU (programmable logic controllers).
  • Insured Modicon programmable logic controllers were properly functioning.
  • Received further training and worked on digital control systems, digital electro-hydraulics and programmable logic controllers (PLC).
  • Installed drives and programmable logic controllers (PLCs) in start-up of new equipment.
  • Worked with Siemens Programmable Logic Controllers, Endress Hauser Instrumentation including Pressure, Temperature, Flow, Level and Analytical Transmitters.

Show More

2. Electrical Systems

high Demand
Here's how Electrical Systems is used in Instrument And Electrical Technician jobs:
  • Supervised personnel performing scheduled and unscheduled maintenance of electrical systems and components on fixed wing P-3C aircraft.
  • Assist in commissioning of instrumentation and electrical systems throughout compressor stations.
  • Maintained and repaired instrumentation and electrical systems including 24-130,000 volt systems.
  • Authored documentation for the facility's instrumentation and electrical systems.
  • Modify existing instrument and electrical systems.
  • Reduced electrical related shutdowns, by implementing (PM's) Preventive Maintenance procedures on both critical and non-critical electrical systems.
  • Supervised all instrument hookup, loop checks, motor hookup and electrical inspection of all instrument and electrical systems.
  • Repaired and maintained plant electrical systems including but not limited to motors, relays, solenoids and plant lighting.
  • Perform troubleshooting, correction, and fine tuning of electronic and electrical systems to ensure accurate and precise control.
  • Install, troubleshoot, maintain, PM all types of instrumentation/controls and electrical systems throughout the plant.
  • Supervised four I&E Technicians in the maintenance and troubleshooting of plant instrument and electrical systems.
  • Lead technician for Pensacola Beach waste water plant, responsible for maintaining all plant electrical systems.
  • Insure all instrumentation, and electrical systems are properly installed, calibrated, and maintained.
  • Trained other team members in the areas of instrumentation, control, and electrical systems.
  • Performed installation, repairs and maintenance of electrical systems, Low and High Voltage.
  • Calibrate, install, troubleshoot, & repair all instrumentation & electrical systems.
  • Maintained, repaired, tested and calibrated all instruments and electrical systems.
  • Research and install new equipment and upgrades to controls and electrical systems.
  • Install, troubleshoot, repair, and maintain instruments and electrical systems.
  • Ensured reliability and safety of all electrical systems in the plant.

Show More

3. Motor Control Centers

high Demand
Here's how Motor Control Centers is used in Instrument And Electrical Technician jobs:
  • Read and correct Wire Schematics, Build Motor Control Centers from the ground up.
  • Worked all aspects of instrumentation, pneumatic, electrical and motor control centers.
  • Demonstrated total physical plant power requirements from substation to installation of motor control centers.
  • Fabricated and wired electrical power control circuits and motor control centers for industrial applications.
  • Installed, upgraded several Motor control centers.
  • Switch boards, load centers, motor control centers and other electrical systems.

Show More

4. Temperature Transmitters

high Demand
Here's how Temperature Transmitters is used in Instrument And Electrical Technician jobs:
  • Calibrated instruments to include pressure, flow, and temperature transmitters.
  • Flow, level, pressure, PH and temperature transmitters.
  • Calibrate level, flow, temperature transmitters.
  • Calibrate pressure, flow, level, and temperature transmitters, H2S, LEL, UVIR fire detection monitors.
  • Calibrated and repaired Pressure and Temperature transmitters.
  • Performed calibrations on pressure transmitters, temperature transmitters, actuator valves, level probes, flow transmitters and gas detection equipment

Show More

5. Control Valves

high Demand
Here's how Control Valves is used in Instrument And Electrical Technician jobs:
  • Maintained transmitters, control valves, analyzers, and microprocessor control system to provide continuous operation of the process unit.
  • Trouble shoot process control equipment, such as: Transmitters, control valves, interlocks, and various other equipment.
  • Repair control valves and perform preventive maintenance on temperature, flow, and pressure and level control devices.
  • Install, troubleshoot, and repair instruments, control valves, motors, and lighting systems.
  • Maintained flow control valves, ball valves as well as rebuilding of these valves.
  • Calibrate differential pressure transmitters, modulating control valves, thrust and vibration probes.
  • Assembled new control valves, and knowledgeable of various control valves components.
  • Perform all calibrations on control valves, transmitters, analyzers and sensors.
  • Rebuild control valves in shop and various equipment in shop.
  • Control valves, I/P, actuators and damper controls.
  • Perform functional and stroke testing of control valves.
  • Delivered the control valves back to various plants.
  • Control valves, butterfly valves, etc.
  • Perform field modifications, install solenoids, switchpacks, go-switches and routine maintenance checks on Block Valves, Throttling Control Valves.
  • Installed Lighting, Heat tape, Roto Meters, Level indicators and control Valves.
  • Repaired all types of control valves, actuators, and positioners.
  • Maintained Fisher and Kammer control valves.
  • Calibrate and troubleshoot instrumentation such as MSA combustible/oxygen monitors, Rosemount transmitters, and Flowserve/Samson/Fisher control valves.

Show More

Job type you want
Full Time
Part Time
Internship
Temporary

6. Control Systems

high Demand
Here's how Control Systems is used in Instrument And Electrical Technician jobs:
  • Performed troubleshooting repair, calibration and general maintenance of large industrial plant operating and control systems using schematics and logic drawings.
  • Performed advanced diagnostic and trouble-shooting of control systems, electrical and mechanical problems; ensuring minimal amounts of production down-time.
  • Calibrated and maintained control systems on all Instrumentation components as needed.
  • Maintained and repaired process instrumentation and electrical control systems
  • Engineered and assembled control systems and instrumentation interfaces.
  • Power Generator Control Systems Maintenance and Troubleshooting.
  • Tasked by Senior Technicians to repair and calibrate all process control systems including controllers, transmitters, valves and switches.
  • Carry out regular reviews of critical process control systems (standing alarms, inhibits and loop faults, etc.)
  • Installed and repaired generators, switch gears, and low voltage control systems, installed and maintained solar systems.
  • Install, maintain, and repair automation and control systems for the production of fuel rods for reactors.
  • Implement, maintain, and monitor all process and control systems associated with steam turned Turbine/Generator Power Generation.
  • Trouble shoot, fix, and maintain all instrumentation, electrical, and control systems for process production.
  • Worked with Allen Bradley PLC and digital control systems with some knowledge of programming and ladder logic.
  • Spearheaded projects reworking control systems, saving on future maintenance costs and reducing waste of finished products.
  • Maintained HRSG, SCR & Refrigerant Compressors, and all Turbine & Generator control systems.
  • Design, fabricate, install, test, modify and troubleshoot electrical and control systems.
  • Performed Construction and maintenance of median voltage and pot line distribution and control systems.
  • Calibrate, maintain, and repair all instruments and control systems within refinery location.
  • Inspected, and commissioned new, and revised existing safety and process control systems.
  • Install and wire new electrical devices during upgrades of obsolete control systems.

Show More

7. Preventative Maintenance

high Demand
Here's how Preventative Maintenance is used in Instrument And Electrical Technician jobs:
  • Performed various maintenance duties, including preventative maintenance, troubleshooting and repair of all electrical and instrumentation systems.
  • Perform preventative maintenance services and calibrations of all site instrumentation and electrical systems and equipment following approved procedures.
  • Port Arthur TX.-Instrumentation/Electrical Technician {Preventative Maintenance Coordinator}, Environmental Technician A/Lead Technician 06/1989 to 07/1992
  • Performed semi-annual preventative maintenance outages on paper mill electrical components and instrumentation, increasing production reliability.
  • Create and perform procedures of preventative maintenance and calibrations on Instrumentation and electrical systems.
  • Perform preventative maintenance on mobile equipment and fuel handling systems routinely and thoroughly.
  • Performed daily and preventative maintenance and troubleshooting on plant-wide electrical and instrumentation systems.
  • Performed all electrical preventative maintenance and scheduled repairs on industrial process systems.
  • Performed preventative maintenance on electrical, and mechanical equipment.
  • Performed preventative maintenance on instrumentation and electrical switch gear.
  • Performed preventative maintenance activities as required.
  • Selected to work on the Compressed Air Team committed to eliminating compressed air downtime, energy savings, and preventative maintenance.
  • Commission and start-up of all associated equipment, preventative maintenance, coordinated shut down of equipment with procurement of parts.
  • Preformed routine preventative maintenance of instrumentation, conduit, tubing, motor controls, and valves.
  • Developed or upgraded preventative maintenance procedures for equipment, parts, or systems.
  • Update and write procedures for preventative maintenance program related to I.S.O.
  • Performed daily preventative maintenance tasks; working closely with Millwrights.
  • Conduct and maintain records on preventative maintenance of equipment.
  • Played critical role in development and implementation of preventative maintenance program that significantly improved ability to keep equipment in running status.
  • network to attach equipment to work orders, browse all preventative maintenance task, and close out work orders.

Show More

8. Variable Frequency

high Demand
Here's how Variable Frequency is used in Instrument And Electrical Technician jobs:
  • Trouble and repair PLC's, Variable Frequency Drives, and Instrumentation controllers (transmitters, flow valves, radars).
  • Maintain electronic programmable logic controls, variable frequency drives, closed circuit camera equipment, and other electronic equipment.
  • Diagnose and repair mobile overhead cranes both P&H static step less and variable frequency drive type systems.
  • Experience with motor starters up to 4160V and Variable Frequency Drives, including specialized high-power drives.
  • Completed installation of plant air compressors, variable frequency drives for primary sludge and DAF units.
  • Install and Maintain Variable Frequency Drives 480 Volt to Medium Voltage Drives Up to 4160.
  • Program Allen Bradley Variable Frequency Drives.
  • Maintained an AC variable frequencydrive center, which ran motors from fractional horsepower motors to 1,000 horsepower motors with regenerative braking.
  • Preformed the installation, programming, and repair of soft starts, variable frequency drives and contactors.
  • Trouble shot and fixed issues with the Allen Bradley powerflex 700 variable frequency drives.
  • Experienced with Siemens, Robicon and Toshiba variable frequency drives.

Show More

9. VFD

high Demand
Here's how VFD is used in Instrument And Electrical Technician jobs:
  • Maintained, installation and troubleshooting of Motors and MCC, and VFD systems 13800V, 4160V and 480V.
  • Worked as part of the maintenance team to repair or replace VFD's Relays, and motors.
  • Calibrated, setup and installed VFD's (Toshiba, Frantic, A/B etc.)
  • Assisted with installation of VFD's, replaced and configured cards after troubleshooting PLC's
  • Repair and maintain all VFD's Allen Bradley, Reliance, and Toshiba.
  • Installed and assisted in the programming of multiple VFD's.
  • Install and program Variable Frequency Drives (VFD).
  • Maintain Siemens liquid cooled and air cooled VFD's.
  • Wire and program VFD's for 6 hp to 1660 hp motors.
  • Upgrade process tanks with a VFD, Agitator, and Load Cells.
  • Installed, troubleshoot, and programmed VFD'S and DC Drives.
  • Install, set up, and troubleshoot VFD's.
  • Work with AC and DC motors, VFD'S.
  • Install and program Allen-Bradly and Siemens VFD's Refurbish electrical buckets with Allen Bradly soft starters.
  • Set new VFD's so as to allow for maximum production output.
  • Maintained Allen Bradley 7000 vector series VFD's * Delta V dcs system
  • Program and troubleshoot ABB and Eaton VFDs.
  • Included temperature, pressure, level, flow, vacuum, VFDs, control valves, and electro-pneumatic actuators.
  • Pump panels, control panels VFDs, new construction, services calls and maintenances.
  • Install and program various Allen Bradley Powerflex VFDs.

Show More

10. Process Control

high Demand
Here's how Process Control is used in Instrument And Electrical Technician jobs:
  • Performed installation and repair of process control instrumentation used in a large petrochemical manufacturing facility.
  • Process control improvements for incremental improvements in quality, productivity and waste reduction.
  • Develop and implement improvements to process controls to increase equipment reliability.
  • Recommended and participated in all process control and development activities.
  • Maintain digital and analog process control equipment.
  • Company specialized in Industrial process controls.
  • Field engineering of new instrumentation devices for improved process control and cost savings through OEE and increased production rates.
  • Document inspections, maintenance, repair work, and failures in maintenance logs and statistical process control charts.
  • Installed, maintained, calibrated, and repaired power distribution, motor control and process control equipment.
  • Install, maintain, and repair process control equipment and electrical equipment necessary for plant operation
  • Completed the proven skill programs in electrical, instrumentation, & process control.
  • Worked on all aspects of instrumentation, pneumatic and electronic for process control.
  • Coordinate with process controls in performing shutdown audits and instrument loop checks.
  • Perform installation, repair, and calibration of mill process control instrumentation.
  • Work instrument process control throughout the IBM plant.
  • Perform instrumentation and electrical duties on process control instruments Adhering to Dupont and Industry safety policies and procedures.
  • Trouble shoot, fix, and maintain I/E equipment for efficient process control through out seven units.
  • Process Control Instrument and Equipment Start Up at Arrow pipeline in Keene North Dakota

Show More

11. Electric Motors

high Demand
Here's how Electric Motors is used in Instrument And Electrical Technician jobs:
  • Repaired and rebuilt electric motors, generators and motorized equipment.
  • Replaced electric motors and rewired motors.
  • Job Duties- Maintain and service all electrical circuits, devices, electric motors, and machines.
  • Repair electric motors, pumps, boilers, emergency lighting & outlet testing.
  • Automated diesel and electric motors for pump station.
  • Performed preventive maintenance on all electric motors ranging from fractional horsepower to 600 horsepower including greasing, alignment and bearing changes.

Show More

12. DCS

high Demand
Here's how DCS is used in Instrument And Electrical Technician jobs:
  • Assisted operators in troubleshooting of operational problems and assisted them in learning basic instrumentation/DCS activities.
  • Worked alongside Sinclair Oil Refinery employees testing new instruments, DCS, and PLC systems installed during the Crude Unit shutdown.
  • Maintained all electrical, instrumentation and control devices (PLC & DCS) including programming PLC's and Reliance coordinated drives.
  • Have had PLC training DCS training, and have utilized it in maintenance and improvements to the Delta V DCS.
  • Work with software and hardware for PLC's and related modules to interface with the DCS operating system.
  • Repaired and calibrated digital instrumentation, DCS, radiation level detectors, density meters, and PLC's.
  • Conduct configuration changes as needed to the DCS controls and installing PLC programs for various plant systems.
  • Performed troubleshooting on motor controls, PLC's, DCS's, variable frequency drives; etc.
  • Helped install and maintain a new DCS operating control system with over 11,000 inputs and outputs.
  • Use Distributed Control Systems (DCS) and Programmable Logic Controller (PLC) to troubleshoot.
  • Trained I&E Technicians how to perform basic programming on PLC's and DCS systems.
  • Experienced with DCS control system, Allen Bradley PLC, VSD & motor starters.
  • Analyze, troubleshoot and program PLC and DCS systems including associated equipment and processes.
  • Use various PLC and DCS to trend and diagnose instrumentation and operational issues.
  • Experience in troubleshooting wiring issues from the field, to the DCS.
  • Maintain and repair any DCS and PLC needs that may occur.
  • Program PLC and DCS systems for process automation and control.
  • Perform DCS and SIS Maintenance, Troubleshooting, & Repair.
  • Trained staff in the installation and testing of DCS Systems.
  • Program shutdowns, displays, overlays and report on DCS.

Show More

13. I/P

high Demand
Here's how I/P is used in Instrument And Electrical Technician jobs:
  • Worked on I/P's, tubed up instruments with poly tubing and hard pipe.
  • Calibrate and troubleshoot Transmitters, I/P, Valve controllers.
  • Stroked valves and adjusted I/P's.
  • Checked loops, & set up I/P transducers.
  • Performed loop checks on smart transmitters, ESD systems, I/P transducers, fire and smoke detection systems.
  • Field serviced as well as calibrated a variety of I/P pressure, level transmitters, differential pressure switches, and valves.

Show More

14. AC

high Demand
Here's how AC is used in Instrument And Electrical Technician jobs:
  • Removed existing conveyor and packaging system from Hershey Candy Company and installed automated conveyor and robotic packaging system working with engineers.
  • Educated and well-practiced in the laws and safety procedures required for electrical and instrumentation installation and commissioning on offshore drilling rigs.
  • Diagnosed and corrected problems accurately and promptly; interacted with the Instrument/Analyzer manager, equipment vendors, and maintenance contractors
  • Communicate with site customers and gas control to ensure maintenance activities are coordinated and performed safely and effectively.
  • Worked closely with engineering and vendor reps to facilitate modifications of prototype machinery and process control systems.
  • Exercise company practices, industry standards, agency/government regulations and have obtained all required licenses and certificates.
  • Calibrated and inspected relevant devices for systems as well as performed maintenance on the facility communications systems.
  • Complete overhaul in shop environment to include component replacements, alignments and calibration to specifications of record.
  • Performed mechanical, electrical, and instrumentation pm's on various manufacturing equipment and electrical panels.
  • Provide on-site quality-control checks on new controller installations performed by contractors before site is turned over.
  • Trained personnel on process safety management and created best practices procedures using word processors.
  • Maintained security access control mainframe and peripheral equipment for nuclear materials processing plant.
  • Experienced in troubleshooting including manufacturing systems as well as instrument and electrical systems.
  • Coordinated and directed shift Electrical & Instrument maintenance of production facilities.
  • Facilitated capital improvement projects for enhanced production and safety upgrades.
  • Maintain accurate records of work using Foundation Architecture management software.
  • Trace and troubleshoot electrical/instrument faults on the processing/manufacturing plant.
  • Provided technical support of operation control rooms and facilities.
  • Tracked equipment performance and ensured warranty work was completed.
  • Performed various modification activities on plant electrical systems.

Show More

15. Instrumentation Technician

average Demand
Here's how Instrumentation Technician is used in Instrument And Electrical Technician jobs:
  • Launched tenure with Dominion Energy and retained position as Instrumentation Technician upon acquisition from Island Operating Services.
  • Included 4-year Electrical and Instrumentation Technician apprenticeship.
  • Direct participation on assessment purchasing, installation, qualification, validation and servicing equipment's, machines and instrumentation technician.
  • Lead telemetry and instrumentation technician for large counter Improvised Explosive Device system development team.
  • Started as an apprentice and rose to journeyman electrician and junior instrumentation technician.
  • Promoted to Senior Instrumentation technician.

Show More

16. Pressure Switches

average Demand
Here's how Pressure Switches is used in Instrument And Electrical Technician jobs:
  • Tested installed and calibrated transmitters, pressure switches and thermo couples.
  • Calibrated and installed pneumatic differential pressure switches in chemical plants.
  • Work on doing calibrations on pressure switches, transmitters, and other electrical devices.
  • Replaced flame scanners, various differential pressure switches, and servo valves.
  • Analyze pressure switches, go switches and replace when needed.
  • Calibrated differential pressure switches, level switches and vibration switches.

Show More

17. Flow Meters

average Demand
Here's how Flow Meters is used in Instrument And Electrical Technician jobs:
  • Calibrate, repair, and change various control equipment from area gas detectors, flow meters and control valves.
  • Perform meter proving and witness's calibrations on flow meters.
  • Mass and Mag Flow Meters 10.
  • Installed various flow meters, such as Rosemount I am able to work with Allen-Bradley PLC's.
  • Experienced with micro-motion, flow meters using Prolink Software.
  • Set up and tested resistor temperaturedetectors, pressure transmitters, flow meters, thermo-couple temperaturemeasuring systems.

Show More

18. VAC

average Demand
Here's how VAC is used in Instrument And Electrical Technician jobs:
  • Performed testing and repair of emergency systems such as fire suppression, emergency stops, evacuation alarms, and notification system.
  • Performed all instrument calibrations in the plant, level, pressure, Airflow, product scale controllers and vacuum.
  • Skilled in the installation, maintenance, electrical devices from 24 volt DC to 4160 VAC.
  • Skilled in safely performing work on electrical system voltages up to 12,970 VAC.
  • Installed and maintains the electrical on manufacturing equipment, conveyor systems and HVAC.
  • Test, inspect and troubleshoot 480VAC motor control center buckets.
  • Upgraded and maintained building systems, including lighting and HVAC.
  • Worked with voltages ranging from 24vdc to 13,800 vac.
  • Team member for hurricane evacuation program.
  • Test process for vacuum, (columns, lines, etc.).
  • Wire up 480VAC & 2300VAC motors.
  • Perform various preventive maintenance and troubleshooting on 24VDC to 4160VAC Install, calibrate, and troubleshoot various types of instrumentation.
  • Maintain 3-phase motor-driven compressors and pumps from 5-3000 hp with voltages from [ ] VAC.
  • Work with voltages up to 13.8kv Maintain HVAC systems for plant.
  • Perform routine maintenance on 480 VAC motor starters and switchgear.
  • Work with voltages from 12vdc to 3 phase 690vac.
  • Performed thermography infrared scanning on the 480 Vac and 2400 Vac electricalequipment utilizing the Flir ThermaCAM PM 575.
  • Maintained 120 VAC, 480 VAC, 4160 VAC, and 3 phase motors.

Show More

19. PLC

average Demand
Here's how PLC is used in Instrument And Electrical Technician jobs:
  • Monitor daily routine checkup generating panel board PLC, controls equipment energize with the maximum safety precaution implementation.
  • Converted pneumatically controlled processes to PLC controlled processes in solvent recovery area.
  • Supported multiple PLC and electrical controlled automated systems.
  • Provided PLC programming and configuration.
  • Experienced in installation, wiring, & setup of overhead crane controls & feeders including Allen Bradley PLC & field components.
  • Installed base Rockwell Automation PLC's, data highway plus network up to pyramid integrator-main frame batching system.
  • Performed advanced and routine troubleshooting activities utilizing PLC programs, schematics, P & ID and circuit tracing.
  • Modified PLC programs and panel views, as required by operations and maintenance management, for process improvement.
  • Provided electrical troubleshooting on PLC's, motor controls and drives as well as process control instrumentation.
  • Wired 480 volt motors in both the control and power circuits and can read PLC logic diagrams.
  • Installed PLC cabinet and landed field wires in the cabinet inside the motor control room.
  • Worked on loop drawings and Commissioning of PLC panel, ESD and TSD panel.
  • Installed and program upgrade of drives and PLC Code for complex Web tension control.
  • Trained and certified to program Allen Bradley, Siemens, and HiMax PLC's.
  • Assisted in building PLC, s for changes in new and old chemical processes.
  • Repaired and programmed Allen Bradley PLC-5 family processors using RSLogix5, 500 programming software.
  • Collaborated with Rockwell Automation technician to install, test, and troubleshoot PLC issues.
  • Work projects that involved electrical improvements, modifications and Allen Bradley PLC5 Programming.
  • Terminated and commissioned all fisher ROC and PLC panels for all locations.
  • Train other maintenance personal on troubleshooting using a PLC and electrical prints.

Show More

20. RTD

average Demand
Here's how RTD is used in Instrument And Electrical Technician jobs:
  • Replaced, Troubleshoot PLC logic, RTD, Vibration probe of steam turbine
  • Repaired and installed pressure switch, thermocouple, RTD and PH Meter.
  • Worked with variable frequency drives, thermocouples, RTD's.
  • Replaced RTD's thermoueouplas, extension wire etc.
  • Perform RTD and thermocouple checks.
  • Experienced with Transmation temperature transmitters using RTD's and Thermocouples analyzer systems utilized in a refinery.
  • Install and wire AC/DC drives, motors, Honeywell controllers, RTDs, lighting, and control panels.
  • Bench calibrates pressure transmitters, control valves, thermocouples, rtds, flow transmitters etc.
  • Used "Hart Smart" communicators to setup transmitters along with Miliamp sources and RTD simulators.

Show More

21. High Voltage

average Demand
Here's how High Voltage is used in Instrument And Electrical Technician jobs:
  • Trained new employees on the theory and operation of electric shovels, electric haul trucks and high voltage cable repair.
  • Route and gland cables(low and high voltage), as well as troubleshooting lighting circuits, panels etc.
  • Test and switch 13,200-volt systems to facilitate substation maintenance and repair using high voltage testers and high voltage PPE.
  • Have worked on high voltage OCB's, ACB, transformers, and associated power lines and control wiring.
  • Experienced working with high voltage such as 2300 to 18 KV and high voltage preventive maintenance processes.
  • Repaired high voltage switch gear, including 13,800-2,300 and 480 volt units.
  • Work on low, medium and high voltage equipment up to 230kv.
  • Perform maintenance and switching on high voltage equipment throughout plant.
  • Performed electrical aspects of low and high voltage.
  • Conducted all high voltage tests on electrical equipment.
  • Certified in high voltage splices, stress cones.
  • Switch gears, high voltage panels, and posts.

Show More

22. Test Procedures

average Demand
Here's how Test Procedures is used in Instrument And Electrical Technician jobs:
  • Develop and perform electrical test procedures for custom control systems
  • Documented all test procedures and test equipment requirements.
  • Generated field test procedures for testing and surveillance for new instrumentation systems.
  • Use of documented test procedures and independent application of professional skills in troubleshooting, repair, testing, assembly and calibration.
  • Reviewed, analyzed, and corrected prototype test procedures.
  • Use of test procedures for QC testing and calibration of instruments.

Show More

23. Foxboro

average Demand
Here's how Foxboro is used in Instrument And Electrical Technician jobs:
  • Performed all troubleshooting, preventive and predictive maintenance on all process instrumentation, PLC's and Foxboro I/A DCS.
  • Trained on the Foxboro Control system to install jumpers, make graphics, and troubleshoot any DCS issues.
  • Rolled over thirty plus motors from Foxboro Spec 200 to the MOD V process control system.
  • Process troubleshooting with operations on the Foxboro I/A DCS.
  • Converted plant from pneumatic to Foxboro DCS.
  • Integrate both Foxboro and Allen-Bradley systems.
  • Will communicate with transmitters to save engineered specifications using Hart/Foxboro, Meriam, or Honeywell communicators.
  • Worked with various types of instrumentation including Foxboro and Rosemount transmitters and calibration equipment.
  • Worked on all plant instruments including all types of Rosemount and Foxboro transmitters, pressure and temperature switches.
  • Program and troubleshoot Control Logics, PLC 5/60, 5/40, 5/20, and SLC 500 as well as Foxboro DCS.
  • Worked extensively with Masonelian valves, Rosemont smart transmitters, and Foxboro pneumatic transmitters.
  • Perform repairs on Lantech stretchwrap machines, Mettler-Toledo scales, Foxboro, Rosemount, micromotion & Allen Bradley equipment.

Show More

24. HMI

average Demand
Here's how HMI is used in Instrument And Electrical Technician jobs:
  • Programmed Allen Bradley logic controllers, drive systems and HMI's.
  • Programmed PLC's, HMI Panels and PROFIBUS communications.
  • Design and program HMI screens using FactoryTalk SE/ME.
  • Total flow and HMI programming and configuration.
  • Installed Program and test programs, PLC's, network switches & HMI panels.
  • Job Duties: PLC(Allen Bradley) and HMI (Intellution)programming for high speed packaging equipment.
  • Key Results: Install & maintain all instrumentation devices and support with PLC & HMI.
  • Experience with Honeywell Experion DCS, including Control Builder and HMI display builder.
  • Create and maintain, and install Wonderware based HMI systems.
  • Integrate Siemens programming and HMI software on all Freemyer equipment.
  • Experience with RS View and Factory Talk HMIs.
  • Designed Panelview HMI screens for control room operators.
  • Program, implement and maintain new control systems, utilizing Allen Bradley and Siemans PLC's with Factorylink HMI.
  • work performing multicraft maintenance at HMI.

Show More

25. Level Transmitters

average Demand
Here's how Level Transmitters is used in Instrument And Electrical Technician jobs:
  • Bench and field calibrations of pressure, temperature and level transmitters.
  • Level transmitters, Siemens Multi-Ranger Ultrasonic probe and Vega radar.
  • Repair instrument equipment as follows: pressure transmitters, level transmitters, pressure switch and transmitters, turbine instrumentation.
  • Installed and maintained analog devices used for input reference, such as flowmeters, level transmitters and pressure transmitters.
  • Calibrated and troubleshoot flow,temperature, pressure, and level transmitters.
  • Performed calibrations of level transmitters, pressure transmitters.

Show More

26. Scada

average Demand
Here's how Scada is used in Instrument And Electrical Technician jobs:
  • Programmed PLC, HMI & SCADA systems* Assisted Engineers with upgrade of control system, production & utility equipment.
  • Service, Backup, and Maintain SCADA, Domain Controller, & SQL Historian Servers.
  • Worked closely with engineering and IT department to implement plant SCADA system.
  • Installed and maintained SCADA system.
  • Program, Modify and Maintain SCADA, HMI, & OIT equipment.
  • Installed and calibrated numerous pressure, level, and flow transmitters, and integrated all the I/Os on SCADA.
  • Develop and maintain SCADA wireless Ethernet network using layer 2 and layer 3 OSPF configuration.
  • Helped improve data acquisition and control in solvent recovery utilizing PLCs and SCADA system.
  • Maintain Cat-5/6, Fiber Optic, & wireless PLC/Scada Ethernet & Leased Line networks.
  • Install, repair and calibrate all instrumentation throughout a modern wastewater facility.Including but not limited to SCADA and PLC Systems.
  • Experience troubleshooting and working with Controlnet and Ethernet IP integrated with wonderware in touch HMI implemented into a SCADA system.
  • Instrument & Electrical Technician: Skills added includes: Maintaining and programming iFIX SCADA/HMI packages.

Show More

27. Instrumentation Equipment

average Demand
Here's how Instrumentation Equipment is used in Instrument And Electrical Technician jobs:
  • Maintain instrumentation equipment for government contractor at a chemical weapon disposal facility.
  • Installed and maintained electrical and instrumentation equipment for use on petrochemical plants.
  • Purchased all electrical and instrumentation equipment.
  • Installed, repaired, calibrated, and designed control and instrumentation equipment to monitor and improve the steel making process.
  • Maintain instrumentation equipment such as pressure, temperature, flow, current, and speed transmitters.
  • Maintain electrical and instrumentation equipment with primary responsibilities over control and measurement devices, including PLCs.
  • Maintained electrical and instrumentation equipment, such as motor starters, switch gear, valves and positioners.
  • build, design, fix and troubleshoot industrial controls and instrumentation equipment.
  • plant wide, including the power plant, water treatment area supporting and maintaining electrical and instrumentation equipment.

Show More

28. Control Loops

average Demand
Here's how Control Loops is used in Instrument And Electrical Technician jobs:
  • Maintained all instrumentation control loops and devices to include steam, flows, level and cascade loops.
  • Tune control loops in order to obtain the best possible control characteristics.
  • Perform Scheduled PM's on Instruments and Control Loops.
  • Calibrate and troubleshoot electronic / pneumatic control loops.
  • Installed, calibrated and maintained process control loops.
  • Integrated new and existing process control loops.
  • Perform instrument calibrations, adjust control loops, and troubleshoot and repair PLCs and distributed control systems.
  • Install new or modifie various parts of control loops as required.
  • Experienced with control loops and troubleshooting through a profibus network Connecting and troubleshooting 900+ instruments PLC Troubleshooting and automation experience.

Show More

29. ABB

average Demand
Here's how ABB is used in Instrument And Electrical Technician jobs:
  • Maintained and calibrated Yokogawa, EndressHauser, and ABB pH/conductivity analyzers.
  • Perform calibration of ABB Meters for Ph, Endress Hauser for flow and Rosemount DP Cell for level.
  • Developed and implemented training programs for E&I mechanics, engineers and management on ABB and Honeywell systems.
  • Program and troubleshoot ABB IRB 6400 Robots and FANUC RJ3 controlled robots.
  • Worked on ABB and GE Turbine systems & Bentley Nevada Vibration Monitoring System.
  • Provide support and maintenance services to Abbott Diagnostic Utilities.

Show More

30. PID

low Demand
Here's how PID is used in Instrument And Electrical Technician jobs:
  • Read PID specifications for inspections including single-line diagrams; ladder logic; and wiring schematics.
  • Calibrated and Tuned PID controllers and made all repairs on DCS highway gateway networks.
  • Used lots of control loop, PID's and electrical diagrams.
  • Tuned PID s to maximize system reliability and efficiency.
  • Completed Rapid Lean Six Sigma yellow belt certification training.
  • Worked from PID Drawings and documented as build's.

Show More

31. Control Panels

low Demand
Here's how Control Panels is used in Instrument And Electrical Technician jobs:
  • Designed, assembled, installed, programmed and commissioned process specific electrical control panels.
  • Involved in manufacturing and design of various electrical and pneumatic control panels including PLC construction and pneumatic well control panels.
  • Design electrical control panels using AutoCad LT. Design, build, wire and program panels to upgrade equipment.
  • Perform Electrical & Instrument conduit with wiring installation and wiring termination at control panels and field instruments.
  • Design, build, program, and maintain control panels in lab and process area situations.
  • Assemble complex electrical and electronic appliances such as control panels and electric motors.
  • Installed control panels and tied in generator hookups and lighting circuits.
  • Skilled in maintaining the equipment control panels.

Show More

32. Trouble Shooting

low Demand
Here's how Trouble Shooting is used in Instrument And Electrical Technician jobs:
  • Perform preventive maintenance, Calibration test report, Trouble Shooting, Overhauling of OPSO/UPSO gas regulators and testing.
  • Read wiring diagrams schematics, and other technical drawings to help aid in trouble shooting equipment.
  • Perform trouble shooting, pullout, repair and installation of control valve including valve accessories.
  • Trouble shooting temperature pressure and ?ow transmitters and communications with Honeywell DCS.
  • Trouble Shooting, maintenance and overhauling of 2000, 3000 KVA Transformers.
  • Trouble shooting processes and making instrument changes as needed.
  • Trouble shooting motor starters and contacts.
  • Trouble shooting of Ovation Control System.
  • Control wiring and trouble shooting.
  • Trouble shooting electrical, pnuematic and hydraulic issues that arise with machine and equipment used for manufacturing.
  • Trouble shooting Demag cranes w/ AB PLC and touch screen programming.

Show More

33. Plant Instrumentation

low Demand
Here's how Plant Instrumentation is used in Instrument And Electrical Technician jobs:
  • Perform routine calibrations on all plant instrumentation to ensure accurate operating and control data.
  • Coordinated and scheduled group personnel for the calibration, repair, and installation of plant instrumentation and electrical power.
  • Maintain, repair and troubleshoot all plant instrumentation.
  • Calibrate, troubleshoot and repair plant instrumentation.
  • Maintain and service plant instrumentation.
  • Performed plant instrumentation replacements and scheduled calibrations inside and out of containment.

Show More

34. Instrumentation Systems

low Demand
Here's how Instrumentation Systems is used in Instrument And Electrical Technician jobs:
  • Fabricated, installed, checked, and repaired electrical equipment and instrumentation systems.
  • Insure a safe and timely delivery of electrical and instrumentation systems.
  • Performed breakdown & preventive maintenance on electrical, control & instrumentation systems.
  • Perform maintenance work on electrical/instrumentation systems
  • Performed wide scale variety of tasks related to both electrical and instrumentation systems for temporary seasonal position.
  • Repaired, monitored and troubleshot various instrumentation systems in a time and temperature sensitive setting.

Show More

35. Process Instrumentation

low Demand
Here's how Process Instrumentation is used in Instrument And Electrical Technician jobs:
  • Performed calibration of fire and gas systems, transmitters, process instrumentation and regulators.
  • Performed I & E calibrations, installation and maintenance of process instrumentation.
  • Perform function check and interlock procedures on process instrumentation & electrical equipment as per Dupont and industry policies and best practices.
  • Perform corrective and routine maintenance on process instrumentation; install new instrumentation, working from drawings and schematics
  • Repair and troubleshooting of process instrumentation/analyzer system components or remove and replace defective parts.
  • Performed installation, calibration and documentation of utilities process instrumentation at Pfizer Kalamazoo, MI.

Show More

36. Switch Gear

low Demand
Here's how Switch Gear is used in Instrument And Electrical Technician jobs:
  • Performed PMs on 120KV to 13.8KV substations 13.8KV to 7200 volt shovel substations and the associated switch gear and protection circuits.
  • Diagnosed and performed repairs on high and low voltage power distribution systems, to include switch gear.
  • Maintain generator systems and auto change over switch gear on plant emergency backup power system.
  • Performed all maintenance and up keep of 4160 electric motors and switch gear.
  • Help maintain switch gear and assist other electricians as needed.
  • Repair or replace breaker buckets and switch gear.
  • Traveled to different states to perform electrical testing and simulation of power for teansformers and switch gears.
  • Perform daily scheduled work and predictive preventive maintenance on motors, Contactors, switch gear.

Show More

37. I/O

low Demand
Here's how I/O is used in Instrument And Electrical Technician jobs:
  • Install new and remove old PLC connected devices, including field wiring and terminations, and associated I/O assignments and programming.
  • Worked on and familiarize on DeltaV SIS, DeltaV I/O, Discrete Input, Analog Input, and 4-20.
  • Installed and configured I/O expansion cards to meet new system requirements.
  • Perform SIS Safety loop checks and I/O functionality checks.
  • Maintain and update I/O and Network systems.
  • Task to do I/O verifications and PLC I/O audits of existing panels.

Show More

38. Cems

low Demand
Here's how Cems is used in Instrument And Electrical Technician jobs:
  • Operate, maintain, calibrate, troubleshoot and repair Cirrus CEMS (Continuous Emission Monitoring System) system.
  • Worked on Bailey Net 90, KVB CEMS, AB PLC-2, Hydraulics, Pneumatics, Control Valve Setup and Repair.
  • Maintain and troubleshoot continuous emissions monitory systems (CEMS) including quarterly linearity testing.
  • Performed weekly preventive maintenance on continuous emission monitors systems (CEMS) as directed.
  • Worked to resolve any issues with our CEMS (continuous emission monitoring system)
  • Completed work orders involving instrumentation, CEMS, and weekly PM's.

Show More

39. Osha

low Demand
Here's how Osha is used in Instrument And Electrical Technician jobs:
  • Monitored all OSHA-critical instrumentation and safety interlock systems, maintaining safety and compliance levels.
  • Adhere to safe work practices including lock out/tag out, OSHA regulations, NFPA, and NEC code regulations.
  • Performed DOT, EPA, OSHA, and USCG inspections, testing, calibration, and documentation.
  • Served on PHA committees, and chaired Employee Safety Committee in an OSHA Star Facility.
  • Ensured proper calibration of emission monitors to comply with DHEC, EPA and OSHA regulations.
  • Qualified and maintained electrical skills in accordance with OSHA low voltage standards.
  • Have also completed the OSHA 10 General Industry Safety & Health course.
  • Follow company directives as well as DOT and OSHA rules and regulations.
  • Trained in SAP and OSHA safety standards.
  • Completed OSHA E&I Safety Upgrade Project at Imperial Sugar Refinery, Gramercy, LA.
  • Maintained maintenance compliance PM's for environmental and OSHA Process Safety Management mill-wide.
  • Trained new technicians on cleanroom protocols, FDA compliance, cGMP, OSHA and safety guidelines.

Show More

40. Modicon

low Demand
Here's how Modicon is used in Instrument And Electrical Technician jobs:
  • Assisted engineers programming a Modicon 484 computer interfaced with a P190 programmer.
  • Control and program Siemens S7 and Modicon PLC logic.
  • Worked on a crew of four to perform plant maintenance and upgrades on the Modicon PLC.
  • Design and implementation of plant ESD system utilizing Modicon PLC.
  • Maintain PLC's (including Allen Bradley, GE, & Modicon).

Show More

41. New Equipment

low Demand
Here's how New Equipment is used in Instrument And Electrical Technician jobs:
  • Prepare specifications and drawings for the modification of existing equipment or installations of new equipment.
  • Installed and repaired new equipment including temperature controllers, PLC's, AC&DC drives and pellet transfer systems.
  • Installed new equipment: Maintained the highest standards of quality and ensured complete customer satisfaction with every installation or repair.
  • Assisted on-site engineers and external contractors; to plan and implement installation of new equipment and/or systems.
  • Participate in cost justification studies for continuous improvement, upgrades and new equipment.
  • Used NEC for wire sizing and de rating for new equipment.
  • Work with operations to commission new equipment and to operate plant.
  • Install and oversee all new equipment installations.
  • Create effective training methods on new equipment.
  • Install new equipment as needed.
  • Job consist of new equipment installation, start-up, commissioning for new units.

Show More

42. Ladder Logic

low Demand
Here's how Ladder Logic is used in Instrument And Electrical Technician jobs:
  • Experienced with the developing and manipulation of ladder logic.
  • Read blueprints, P&ID's, ladder logic, and wiring schematics.
  • Experienced in troubleshooting and maintaining ladder logic programming.
  • Utilize knowledge of Ladder Logic Control in conjunction with position.
  • Rework ladder logic to improve scan times and node efficiency.
  • Accustomed to reading schematics, ladder logic, wiring diagrams, loop sheets and P&ID's.

Show More

43. Fluke

low Demand
Here's how Fluke is used in Instrument And Electrical Technician jobs:
  • Use of electrical equipment such as fluke 789, amp probe, and hart communicator
  • Performed differential pressure and temperature transmitter calibrations using Fluke 754 and HART 475.
  • Experienced with Delta V, ASI, Fieldbus, Profibus, PLC's, DPC Track, HART, Fluke 744.
  • Displayed proficiency in use of Fluke Model 744 Programmable Calibrator and associated modules.
  • Full calibrations with Fluke754 tracking.
  • Installed and test data acquisition equipment, Fluke and Campbell, for proper function and programming

Show More

44. Yokogawa

low Demand
Here's how Yokogawa is used in Instrument And Electrical Technician jobs:
  • Repair and rebuild columns, valves and control boards on Seimen Maxum and Yokogawa GC1000 analyzers.
  • Performed Yokogawa recorder setups and calibrations.
  • Performed daily fault finding, loop tuning on PLC'S- RS Logic 5000, Yokogawa Control Net and Device Net.
  • Repair and trouble-shoot PLC issues Allen Bradley PLC 5, Yokogawa GE.
  • Performed shoot loops, Stoke valves, troubleshoot wires on instruments, and wire up Yokogawa DCS.
  • Function checks with Yokogawa DCS system.

Show More

45. Hand Tools

low Demand
Here's how Hand Tools is used in Instrument And Electrical Technician jobs:
  • Experience with hand tools, power tools, and precision measuring/testing instruments.
  • Work with hand tools and test instruments.
  • Operated various hand tools and test instruments.
  • Used pipe benders, punches, hand tools, power tools.
  • Repair or replace wiring, equipment, or fixtures, using hand tools or power tools.
  • Disconnect and/or remove defective or unauthorized meters using hand tools.

Show More

46. ISO

low Demand
Here's how ISO is used in Instrument And Electrical Technician jobs:
  • Collaborated with control center, supervisors and operators to ensure smooth work flow and efficient organization operations.
  • Supported production by diagnosing and isolating system malfunctions in control systems using schematics and appropriate test equipment.
  • Work closely with refinery unit operators to safely isolate and shut-down system components to do repairs.
  • Worked in electrical department, instrument department, then made supervisor in analysis department.
  • Increased personal performance by qualifying as a Collateral Duty Inspector and Work Center Supervisor.
  • Maintained instrumentation and electrical maintenance records and produced reports for supervisors.
  • Worked as an electrical and instrumentation technician and supervisor.
  • Promoted to Supervisor of Plant Electrical and Instrumentation
  • Qualified high voltage electrical technician and supervisor.
  • Worked with Detroit Diesel Engine, Allison Transmission Electronics, voltage ranging from 600, 480, 220, and 110.
  • Consult and coordinate efforts with other workers, supervisors, or engineers involved in installing or maintaining equipment or components.
  • Worked in the field acting as a positive representative for Di-Trol when interacting with other company supervisors and employees.
  • Provided customers with NIST traceable calibration certification on instrumentation as set by their plant ISO and Federal/State guidelines.
  • Performed calibration of process measuring systems in compliance with ISO 9000 standards using the Fluke calibration system.
  • Perform multiple ISO Calibration and record accurate data Within SAP and hard copy filing system.
  • Repair of pneumatic only instruments; perform ISO calibrations and record results in proper documentation.
  • Work was onshore on an LNG Storage Project as Instrument and electrical Supervisor and worker.
  • Reason for leaving: Accepted E&I Supervisor position at New Page Corp.
  • Utilized lock out tag out procedures to isolate any potential energy while performing work.
  • Open and close switches to isolate defective relays, performing adjustments or repairs.

Show More

47. Ethernet

low Demand
Here's how Ethernet is used in Instrument And Electrical Technician jobs:
  • Install, troubleshoot, service, repair industrial networks based on ControlNet, DeviceNet, and Ethernet.
  • Install and maintain Ethernet and fiber optic lines.
  • Program wireless Serial and Ethernet radios, routers, IP cameras and NVRs.
  • Developed and installed DH+, ethernet and DeviceNet.
  • Worked on equipment using CNET, DNET, and Ethernet.
  • Installed and maintained network equipment, including serial radios, ethernet networks and fiber optic networks.

Show More

48. Plant Operations

low Demand
Here's how Plant Operations is used in Instrument And Electrical Technician jobs:
  • Install, repair, and maintain instrument equipment and coordinate instrument equipment installation activities with plant operations and maintenance personnel.
  • Worked off-shift and during weekend and holidays performing maintenance coverage to support plant operations.
  • Coordinated with plant operations for instrument maintenance.
  • Manage all break-in notifications and coordinate work with Plant Operations Dept.
  • Installed multiple DCS process automation changes to insure consistent plant operations and reduce human interaction to reduce operational mistakes.
  • Developed extensive knowledge of plant operations and control systems.

Show More

49. O2

low Demand
Here's how O2 is used in Instrument And Electrical Technician jobs:
  • Installed, repaired and maintained O2 Analyzers.
  • Install, maintain, calibrate and operate a network of ambient sulfur dioxide (SO2) monitors at five sites.
  • Overhaul and re-commissioning of Halon and CO2 fire protection systems, and demonstration of same to Site Safety dept.
  • Monitored CO emissions, and CO2 emissions, utilizing CEMS equipment, also calibrated CEMS equipment.
  • Gained experience maintaining O2, H2S, HF acid, CO and Combustible sensors.
  • Designed Man Machine Interface display panels and control programs using Opto22 Factory Floor software.

Show More

50. New Installations

low Demand
Here's how New Installations is used in Instrument And Electrical Technician jobs:
  • Follow wiring schematics for new installations as well as installed electrical circuits in the plant.
  • Run rigid conduit and tubing containing various radiuses and diameters for new installations, repairs and replacement.
  • Assisted with scheduling and planning of all electrical maintenance and new installations.
  • Supervised General Shutdowns Responsible for tank gauging and oil transfer replacement projects Overseeing of New installations

Show More

20 Most Common Skill for an Instrument And Electrical Technician

Programmable Logic Controllers12.9%
Electrical Systems11.7%
Motor Control Centers10.4%
Temperature Transmitters10.2%
Control Valves9.1%
Control Systems7.4%
Preventative Maintenance4.8%
Variable Frequency4.5%

Typical Skill-Sets Required For An Instrument And Electrical Technician

RankSkillPercentage of ResumesPercentage
1
1
Programmable Logic Controllers
Programmable Logic Controllers
9.8%
9.8%
2
2
Electrical Systems
Electrical Systems
8.9%
8.9%
3
3
Motor Control Centers
Motor Control Centers
7.9%
7.9%
4
4
Temperature Transmitters
Temperature Transmitters
7.8%
7.8%
5
5
Control Valves
Control Valves
6.9%
6.9%
6
6
Control Systems
Control Systems
5.6%
5.6%
7
7
Preventative Maintenance
Preventative Maintenance
3.6%
3.6%
8
8
Variable Frequency
Variable Frequency
3.4%
3.4%
9
9
VFD
VFD
2.8%
2.8%
10
10
Process Control
Process Control
2.3%
2.3%
11
11
Electric Motors
Electric Motors
2.1%
2.1%
12
12
DCS
DCS
2%
2%
13
13
I/P
I/P
1.9%
1.9%
14
14
AC
AC
1.7%
1.7%
15
15
Instrumentation Technician
Instrumentation Technician
1.7%
1.7%
16
16
Pressure Switches
Pressure Switches
1.6%
1.6%
17
17
Flow Meters
Flow Meters
1.6%
1.6%
18
18
VAC
VAC
1.5%
1.5%
19
19
PLC
PLC
1.5%
1.5%
20
20
RTD
RTD
1.4%
1.4%
21
21
High Voltage
High Voltage
1.4%
1.4%
22
22
Test Procedures
Test Procedures
1.2%
1.2%
23
23
Foxboro
Foxboro
1.2%
1.2%
24
24
HMI
HMI
1.2%
1.2%
25
25
Level Transmitters
Level Transmitters
1.1%
1.1%
26
26
Scada
Scada
1%
1%
27
27
Instrumentation Equipment
Instrumentation Equipment
0.9%
0.9%
28
28
Control Loops
Control Loops
0.9%
0.9%
29
29
ABB
ABB
0.9%
0.9%
30
30
PID
PID
0.9%
0.9%
31
31
Control Panels
Control Panels
0.9%
0.9%
32
32
Trouble Shooting
Trouble Shooting
0.9%
0.9%
33
33
Plant Instrumentation
Plant Instrumentation
0.8%
0.8%
34
34
Instrumentation Systems
Instrumentation Systems
0.8%
0.8%
35
35
Process Instrumentation
Process Instrumentation
0.7%
0.7%
36
36
Switch Gear
Switch Gear
0.7%
0.7%
37
37
I/O
I/O
0.7%
0.7%
38
38
Cems
Cems
0.7%
0.7%
39
39
Osha
Osha
0.7%
0.7%
40
40
Modicon
Modicon
0.7%
0.7%
41
41
New Equipment
New Equipment
0.7%
0.7%
42
42
Ladder Logic
Ladder Logic
0.7%
0.7%
43
43
Fluke
Fluke
0.6%
0.6%
44
44
Yokogawa
Yokogawa
0.6%
0.6%
45
45
Hand Tools
Hand Tools
0.6%
0.6%
46
46
ISO
ISO
0.5%
0.5%
47
47
Ethernet
Ethernet
0.5%
0.5%
48
48
Plant Operations
Plant Operations
0.5%
0.5%
49
49
O2
O2
0.5%
0.5%
50
50
New Installations
New Installations
0.5%
0.5%

14,313 Instrument And Electrical Technician Jobs

Where do you want to work?