Quality control technician jobs in Lancaster, PA

1. Execute service and maintenance of production and prototype equipment supporting test activities. Including but not limited to combines, headers, tractors and implements. - Repair equipment failures as needed to keep test engineers operational. - Configure vehicles for testing. - Service equipment as needed to maintain the test fleet. - Order parts through necessary channels. - Wash and clean crop material from vehicles. 2. Maintain the shop facility to ensure a clean work environment and reliable equipment. - Clean areas not addressed by general cleaning crew. - Restock consumables. 3. Manage incoming and outgoing freight shipments. - Unload/load equipment including combines, headers, tractors, and implements being shipped to dealers, customers, and test sites. - Ensure BOLs are signed and communicated. 4. Manage and organize part storage areas. - Scrap identified parts by engineering. - Mark and store parts as appropriate. 5. Assist test engineers on lab and test rigs - Build test rigs. - Provide support to test engineers as needed for part swaps and test monitoring. - Clean labs and organize/service equipment. 6. Setup/stock/organize service truck fleet. - Clean and restock vehicles returning from the field. - Setup new trucks with tools and equipment. - Install accessories as needed. About US Tech Solutions: US Tech Solutions is a global staff augmentation firm providing a wide range of talent on-demand and total workforce solutions. To know more about US Tech Solutions, please visit ************************ US Tech Solutions is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, colour, religion, sex, sexual orientation, gender identity, national origin, disability, or status as a protected veteran. Vikas Kumar Yadav ****************************** ID: 25-53241

TAIT partners with artists, brands, IP holders and place makers to bring culture-defining, never-before-seen experiences to life. With a legacy of innovation spanning over 45 years, TAIT has grown from pioneering in rock 'n' roll concert staging to setting the global standard for extraordinary live events and experiences through cutting-edge technology, precision engineering, and creative design. TAIT's 20 global offices have developed iconic productions and experiences in over 30 countries, all seven continents, and even outer space for renowned performers, theme parks, exhibits, and venues across the globe, including partnerships with Taylor Swift, Cirque Du Soleil, Royal Opera House, Nike, NASA, Bloomberg, Google, Beyoncé, and The Olympics Position Purpose The Production Associate position will assist with all manufacturing, assembly, and fabrication on TAIT products and projects in a group setting or with minimal guidance from the group lead. This position will require the Production Associate to be highly functional in multiple disciplines and help support the fabrication team to deliver a finished product to TAIT's standards of quality. This position also provides access for continued growth as a: Production Technician, Mechanical Fabricator I, or a Water Spider I based on skillset and additional training. Essential Responsibilities - Adhere to and implement proper fabrication and assembly techniques. - Maintain accurate dimensional tolerances set forth on drawings. - Produce a quality product while focusing on TAIT brand quality and standards. - Clean and maintain workspace area, facility tools, and equipment. - Ability to read, understand, and follow blueprints, internal drawings, and SOP's. - Adhere to all company safety policies and procedures. - Attend meetings, seminars, and training sessions as required. - Perform assigned duties according to the policies and expectations prescribed by the company. Minimum Qualifications - High School Diploma or GED. - One (1) year of instructional/professional training. - Skill set focused in general fabrication, carpentry, complex mechanical assembly and/or TAIT experience preferred. - Ability to identify materials and hardware. - Ability to read, understand, and follow blueprints and internal drawings. - Knowledge in rigging equipment and practices (WLL, COG, & LAF). - Advanced knowledge and experience using precision measuring instruments and general manufacturing tools (wood, plastic, metal). - Effective oral and written communication skills. - Ability to use (proficient in) TAIT business systems (Epicor, Slack, and Box). - Capacity to work independently, and as a member of a small team. - Ability to handle changing priorities in a fast-paced environment. - Flexibility with work schedule. Normal work schedule is forty hours per week; however operational demands may necessitate other schedules to meet business needs. Working Conditions The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. The employee is required to frequently walk, bend, climb, push, pull, twist, squat, stoop, and kneel each day. Specific requirements are: - Must be able to stand for extended periods of time - Must be able to lift or move 50 lbs. - Must be able to carry 50 lbs. - Must be able to pull or push 50 lbs. - Must be able to reach overhead - Must be able to work in small, sometimes awkward spaces and positions. TAIT is an equal opportunity employer fully committed to diversity and inclusion in the workplace. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, or status as a protected veteran or any other protected characteristic as outlined by international, national, state, or local laws.

Come Join Us! From apartments in New York to hospitals and stadiums in Dallas, libraries at prestigious universities to creating modern retail experiences, our teams contribute architectural glass and building products to projects that shape the way people live, work, heal, learn, and play. At OBE, the work of our employees truly matters. With over 6,500 employees, we operate more than 80 manufacturing and distribution facilities in five countries. You can see some of our favorite projects here. Start your journey with OBE and help us build the future. What You'll Get to Do The Quality Control Technician is focused on testing materials and finished products to ensure they conform to company standards, and ensure the products are market ready. The Quality Control Tech reports to the Quality Manager. This role is perfect for an individual who has a strong attention to detail, the ability to communicate effectively, and the capacity to work collaboratively to identify and resolve quality issues. A vital member of Quality Control, this is an opportunity to build a career with an industry leader. Job responsibilities include: Approve incoming materials by confirming specifications, conducting a visual and measurement test, and rejecting and returning unacceptable materials Approve all finished products by confirming specifications and conducting required tests Return products for re-work if needed and complete documentation to complete re-work Ensure compliance to federal and state laws, as well as company standards and specifications Perform inspections across all stages of production Prepare and maintain test data for review Evaluate data and draft reports, noting any relevant deviations from existing standards Identify areas for quality control improvement and implement new methods accordingly Communicate quality or compliance concerns with urgency Work towards continuously improving workplace organization, safety, quality, and productivity, and supports an environment that empowers employees. Other duties as assigned. What We Are Looking For High school diploma or general education degree (GED) required Minimum of 2 years of inspection and/or production experience Ability to lift and/or move up to 50 pounds occasionally Specific vision abilities required include close vision, distance vision, color vision, peripheral vision, depth perception, and the ability to adjust focus Demonstrated ability to work independently with minimal supervision Excellent organizational skills Demonstrated ability to analyze and interpret information Understanding of manufacturing methods and procedures What OBE Offers You Benefits that benefit you - industry competitive benefits at the lowest cost to the employee Work-life balance - PTO and holidays, including floating holidays you can choose Compensation that rewards your hard work - A pay-for-performance culture with potential for annual raises and bonuses Training - We will equip you with the knowledge and skills you need to succeed OBE is an Affirmative Action and Equal Opportunity Employer. EOE/Vet/Disability--If you want to know more, please click on this link. Oldcastle BuildingEnvelope is an E-Verify Employer.

**Penn State Health** - **Hershey Medical Center** **Work Type:** Full Time **FTE:** 1.00 **Shift:** Day **Hours:** 8:00a - 4:30p **Recruiter Contact:** Denisse M. Rosado at ******************************** (MAILTO://********************************) **SUMMARY OF POSITION:** Responsible for the coordination, assessment, process improvement, and support for all quality assurance and performance improvement activities. Duties to include, but not limited to: data management, performance improvement, patient safety, and regulatory compliance. Responsible for assisting management with integrating program quality efforts across program components. **MINIMUM QUALIFICATION(S):** + Bachelor's degree **WHY PENN STATE HEALTH?** Penn State Health offers exceptional opportunities to learn and grow, exposure to a wide patient population, and the ability to provide individualized, innovative, and specialized care to patients in the community. **Penn State Health offers an exceptional benefits package including medical, dental and vision with no waiting period as well as a Total Rewards Program that highlights a few of the many additional offerings below:** + **_Be Well_** with Employee Wellness Programs, and Fitness Discounts (University Fitness Center, Peloton). + **_Be Balanced_** with Generous Paid Time Off, Personal Time, and Paid Parental Leave. + **_Be Secured_** with Retirement, Extended Illness Bank, Life Insurance, and Identity Theft Protection. + **_Be Rewarded_** with Competitive Pay, Tuition Reimbursement, and PAWS UP employee recognition program. + **_Be Supported_** by the HR Solution Center, Learning and Organizational Development and Virtual Benefits Orientation, Employee Exclusive Concierge Service for scheduling. **WHY PENN STATE HEALTH MILTON HERSHEY MEDICAL CENTER?** Penn State Hershey Medical Center is Central Pennsylvania's only Academic Medical Center, Level 1 Regional Adult and Pediatric Trauma Center, and Tertiary Care Provider. As a four-time Magnet-designated hospital, Hershey Medical Center values the hard work and dedication that our employees exhibit every day. Through our core values of Respect, Integrity, Teamwork, and Excellence, our employees are a team committed to compassionate care for our diverse patient population, our community and each other. As a valued team member, we promote continued professional development, specialty certification, continuing education, and career growth. **YOU TAKE CARE OF THEM. WE'LL TAKE CARE OF YOU. State-of-the-art equipment, endless learning, and a culture of excellence - that's Penn State Health. But what makes our healthcare award-winning? That's all you.** _This job posting is a general outline of duties performed and is not to be misconstrued as encompassing all duties performed within the position. Eligibility for shift differential pay based on the terms outlined in company policy or union contract._ _All individuals (including current employees) selected for a position will undergo a background check appropriate for the position's responsibilities._ _Penn State Health is an Equal Opportunity Employer and does not discriminate on the basis of any protected class including disability or veteran status. Penn State Health's policies and objectives are in direct compliance with all federal and state constitutional provisions, laws, regulations, guidelines, and executive orders that prohibit or outlaw discrimination._ **Union:** Non Bargained **Position** Quality Associate - Liver Transplant **Location** US:PA: Hershey | Quality | Full Time **Req ID** 85562

Job Description Join Berks Packing Co., Inc. as a Quality Control Technician on the 2nd Shift and immerse yourself in a dynamic environment where your skills directly impact food safety and quality. This role offers a unique opportunity to contribute to innovative practices in food manufacturing, ensuring excellence in every product we deliver to our customers. As part of a forward-thinking team, you will engage with the latest technologies and methodologies, enhancing your expertise in quality assurance. Your commitment to integrity and respect for industry standards will drive our commitment to customer satisfaction. Being part of this dedicated team means playing a key role in shaping the future of food safety and production. Take your career to the next level by applying your passion for quality and making a difference in a respected and traditional organization. Berks Packing Co., Inc.: What drives us Berks Packing is a 3rd generation family-owned and operated meat processor facility located in Reading, Pennsylvania. We have a long-standing tradition of providing excellent product quality and customer service. Berks has been a family favorite for over 92 years! Make a difference as a Quality Control Technician- 2nd Shift As a Quality Control Technician on the 2nd Shift at Berks Packing Co., Inc., you will be responsible for conducting thorough inspections of raw materials and finished products to ensure compliance with safety and quality standards. Your daily tasks will include monitoring production processes, identifying and documenting any deviations, and collaborating with production teams to implement corrective actions. You will perform routine quality assurance tests and maintain accurate records to support quality assurance protocols. Additionally, you'll be expected to contribute to continuous improvement initiatives by sharing insights and recommending enhancements to existing procedures. Attention to detail and adherence to safety regulations will be paramount in this role, as you work to uphold our commitment to excellence and customer satisfaction. Your proactive engagement with team members will foster an environment of respect and collaboration essential for maintaining high-quality standards. What we're looking for in a Quality Control Technician- 2nd Shift Successful Quality Control Technicians at Berks Packing Co., Inc. possess a unique combination of analytical and interpersonal skills critical for ensuring product quality in food manufacturing. Attention to detail is essential, allowing you to identify subtle inconsistencies in products and processes. Strong observational skills will enable you to accurately assess compliance with safety and quality standards. Excellent communication skills are necessary for effectively collaborating with cross-functional teams and articulating quality-related concerns or recommendations. Problem-solving abilities will empower you to investigate issues and implement corrective actions swiftly. A foundational understanding of food safety regulations and quality assurance practices will serve you well, as will a commitment to continuous learning in a fast-paced environment. Adaptability and a strong sense of integrity are crucial traits, as they ensure you uphold our core values while contributing to a culture of excellence focused on customer satisfaction. Join us! We believe in taking care of our team, both on and off the job. That's why we offer a mobile-friendly application process - because we know your time is valuable. If you're ready to take your management skills to the next level and join a team that values hard work and a good culture, complete our application today! A pre-employment physical and drug/alcohol screen is required. We conduct background checks as part of our pre-employment screening process and follow all EEOC and FCRA regulations regarding the use of criminal records in the hiring process.

Job DescriptionDo you have an eye for detail and experience in a Quality Lab setting?***PeopleShare is HIRING IMMEDIATELY for a 2nd Shift Precision Quality Inspector in Lancaster, PA!***Apply today or call Misty at ************Why PeopleShare? We offer full medical benefits from day 1 Chance to work with the top companies in the area Immediate ability to work with 15+ different companies by applying once More local offices than any other agency: we do the networking for you Weekly pay through direct deposit Paid skills training available Earn referral bonuses We offer coaching to help you ace your interview Job Details for 2nd Shift Precision Quality Inspector: Schedule: 2nd Shift: Monday-Thursday 3pm-1:30am *must be willing to train on 1st Shift for 6-8 weeks* Pay Rate: $18-$21+ based on experience Strong Benefits: Medical Dental Vision Retirement PTO Weekly Pay via Direct Deposit! Job Responsibilities & Description for 2nd Shift Precision Quality Inspector: Follow process-driven Inspection steps and documentation Read and apply blueprints and diagrams Use caliper, micrometer, and other tools to verify math-based tolerances Apply strong understanding of math: fractions and decimals Occasionally perform simple Machine Operation Be flexible to perform all duties from a standing or seated position Occasionally lift and carry up to 50lbs Job Requirements for 2nd Shift Precision Quality Inspector: REQUIRED: Must be willing to work 2nd shift hours REQUIRED: Must speak, read, and understand English for safety reasons REQUIRED: Must have reliable transportation - this position is not bus accessible REQUIRED: Must have 1+ year of experience in Precision Quality Inspection using Micrometers, Calipers, Gauges, or similar fine measuring tools REQUIRED: 1+ year of experience working with manufacturing blueprints Preferred: Experience in CNC-machining environment preferred but not required Preferred: Experience in a quality lab or medical manufacturing setting Excellent work history - Must have been consistently employed for the past 2+ years Must have good understanding of math: fractions, decimals + addition, multiplication etc. If you feel you have MOST of the above qualifications, please apply! We want to speak with you!PeopleShare is the leading Staffing Agency in the region and has temporary to hire and permanent jobs in the central Pennsylvania (PA) area - Harrisburg, Camp Hill, Lemoyne, York, Lancaster, Carlisle, Chambersburg, Middletown, Leola, Shippensburg, Ephrata and Mechanicsburg, as well as northern Maryland (MD) - Hagerstown, Maugansville, Williamsport, Boonsboro, Smithsburg, and Hancock. We have openings for receptionist, data entry, customer service, collections, office managers, call center, administrative assistant, accounts payable clerk, accounts receivable clerk, file clerk, warehouse, assembly, production, Machine operator assistants, warehouse material handlers, material handling associates, material handler specialists, material handling experts, machinists, machine specialists, machine operator associates, machine operator assistants, press operators, press assistants, press operator specialists, quality inspection associates, quality inspection specialists, QA, QC, quality assurance, quality control, quality control inspection, quality assurance inspection, machine troubleshooters, machine setup specialists, warehouse pickers, warehouse packers, warehouse forklift, machine operators, and maintenance mechanics. PeopleShare provides equal employment opportunities to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, disability or genetics. In addition to federal law requirements, PeopleShare complies with applicable state and local laws governing nondiscrimination in employment in every location in which the company has facilities. This policy applies to all terms and conditions of employment, including recruiting, hiring, placement, promotion, termination, layoff, recall, transfer, leaves of absence, compensation and training.IND15

Do you have an eye for attention to detail and an impeccable desire to enforce and maintain high standards of Quality? Then look no further and join the Quality Team at Advanced Cooling Technologies, Inc. (ACT) - nominated as a "Best Places to Work" in PA in 2023, York location. The Quality Team ACT is looking for team members who are passionate about creativity and innovation and looking to make a difference every day. We are committed to developing world class Quality Assurance programs, processes, and people that support the ACT mission and family of brands, including Tekgard Environmental Control Units. We have an immediate opening for a Quality Inspection in our York location. Company Overview Advanced Cooling Technologies, Inc. (ACT), with locations in York and headquartered in Lancaster, PA, is a leading manufacturer of innovative thermal management products for diverse applications, serving a broad spectrum of industries including commercial satellites, military vehicles, medical devices, primary calibration equipment, and HVAC systems. We are dedicated to fostering creativity, innovation, and making a tangible difference every day. Our commitment extends to our customers, employees, and community, with core values centered on Innovation, Teamwork, and Customer Care-key drivers of our continuous growth and success. At ACT, our skilled and dedicated staff is our most valuable resource. ACT offers a robust benefits package including low-cost medical, dental, vision, company-paid life and disability insurance, paid time off, a 401k with company match, and a profit-sharing bonus plan. Enjoy a work-life balance at our York location supported by a 4-day work week (4/10 schedule), generous PTO, and 8 paid holidays. Position Summary This position is for a Quality Inspector at our facility located in York, PA. As a Quality Inspector, you will play a hands-on role within the organization and interface with both Operations and Product Development teams while performing incoming inspection of materials and components and performing in-process and final inspections of products for commercial and/or government customers. Key Duties and Responsibilities * Inspect incoming materials * Perform in-process inspections and/or final inspections on manufactured product * Ensure all materials and product meet Quality standards as per policy and ISO9001/AS9100 procedures * Identify and segregate non-conformances and write non-conformance reports * Support Supplier Quality initiatives ACT is an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to race, religion, color, national origin, sex, sexual orientation, gender identity, age, status as a protected veteran, status as a qualified individual with a disability, or any other trait protected by law. Requirements * High School Diploma or GED * Ability to read and interpret blueprints and shop drawings * Ability to use basic inspection tools such as micrometers, calipers, height gages, etc. * Basic computer skills (Outlook, Word, Excel). * Basic math skills * Strong verbal and written communication skills Additional Qualifications (preferred): * Authorized to work in the US. US Citizen, Permanent Resident, or Protected Individual (as defined by 8 U.S.C. § 1324b(a)(3)) preferred due to ITAR responsibilities. * Prior experience with ERP systems

The Quality Technician is responsible for ensuring the quality standards of incoming materials, in-process production, and finished products are met. This role involves inspecting and approving materials and products through various tests, documenting results, and working closely with production teams to resolve quality-related issues. This position reports directly to the Quality Assurance Manager for daily supervision and performance reviews. Summary of Essential Job Functions/Responsibilities Inspect and approve Incoming Materials: Verify specifications of incoming materials through visual and measurement tests. Reject and return materials that do not meet standards Inspect In-Process Production: Monitor ongoing production by ensuring specifications are met through visual and measurement testing. Communicate necessary adjustments to lead personnel or supervisors Approve Finished Products: Confirm that finished products meet quality standards through testing. Return products for re-work when necessary, and ensure re-work is performed and approved Document Inspection Results: Maintain accurate reports and logs of inspection results, summarizing re-work and waste. Input data into the quality database for future reference Maintain Measurement Equipment: Ensure that all measurement tools and equipment are properly maintained and in good working condition. Communicate equipment repair needs when necessary Interpret Blueprints and Specifications: Read blueprints and interpret technical specifications to ensure accurate quality assessments. Ensure Safe Work Environment: Adhere to safety and health protocols, ensuring all tasks are performed within established safety standards Continuous Learning and Skill Development: Update job knowledge by participating in relevant educational opportunities and adopting new skills to improve inspection processes Achieve Organizational Quality Goals: Complete tasks that contribute to meeting organizational quality and operational objectives Other Duties as Assigned: Perform other related duties as required Qualifications Experience: Minimum of four to five years of prior experience in a quality-related position or a comparable role, preferably in the metals industry Work Environment: Experience in an industrial warehouse setting, ideally within the metals industry Industry Standards Knowledge: Familiarity with ISO-9001, QS-9000, ISO-14000 standards and metallurgy preferred Computer Skills: Proficiency in Microsoft Office Suite (Word, Excel, PowerPoint), Adobe, and other relevant software programs Attention to Detail: Must be meticulous, with a strong eye for detail to ensure high-quality standards are maintained Self-Management: Ability to work independently with minimal supervision and demonstrate initiative in completing tasks efficiently Physical Examination: Ability to pass a physical examination for vision, hearing, and mobility Reliability: Demonstrated reliable work history Attention to Detail: Must be detail-oriented with a strong focus on precision and quality in all tasks

Quality Technician | The Shyft Group (FVS) | Landisville, PA Regular Employee | Hourly Non-Exempt | $0.00 - 0.00 What you'll do: The Quality Technician position is responsible for ensuring that the product meets customer's requirements (both internal and external) at each stage of its manufacturing process, carrying out relevant testing and where necessary take corrective action to rectify non-conformance issues. Report quality issues data, ensuring the Quality Management System is adhered to at all stages. * Promote the expectation that team members will consider the impact of their work/actions on others and make deliberate decisions to act in ways which prevent rework or constraints on the process. * The Quality Technician is a coach, cheerleader, and player on the team * Facilitate creation of systems and processes which enhance the team's ability to meet customer expectations (identification of standards, creating of buy/sell agreements, audit processes, etc.) * Act as mediator when needed to clarify customer expectations or interpret standards * Perform Pre-Delivery Inspections of completed vehicles * Perform data entry, analysis, and sharing/explanation of same * Generate reports * Perform audits of new and existing processes * Document writing, control, and management * Facilitate/Participate in Root Cause Analysis, Design Failure Mode and Effects Analysis, Production Failure Mode and Effects Analysis, Practical Problem Solving, etc. • Initiate non-conforming material documents for supplier quality issues * Assist in the execution of activities which promote continuous improvement and protect customers * Conduct training, information sharing and orientation sessions * Lead by example regarding safety and acting in the best interests of the team * Provide coverage for other technicians as needed * Any other duties as assigned by the Quality Manager What you need to be successful: * High School Diplomas or GED required (Associates degree and/or CQT certification preferred) * Minimum 2-3 years related Quality Manufacturing experience * Knowledge of/ability to acquire a thorough understanding of customer expectations and regulatory requirements * Excellent attendance * Positive attitude * Strong interpersonal skills * Ability to read relevant measuring equipment * Provide appropriate feedback and documentation of any defects * Strong and consistent attention to detail * Self-motivated with the ability to stay on task * Team oriented Able to: * Read and understand Engineering documents such as part prints, assembly drawings * Work overtime on short notice Be willing to: * Learn and rotate within all quality areas * Improve self / area / company (including pursuing additional training, if needed) * Develop a working knowledge of company's systems (example: AS/400, Sparcon) Why The Shyft Group? Our people are our greatest asset, and your success is our success! That's why we provide comprehensive benefits that support your health, financial security, and work-life balance-so you can thrive both personally and professionally. * Health & Wellness: Medical, Dental, Vision, HSA/FSA, Wellness Plan * Financial Security: 401(k) with match, Disability, Life Insurance * Work/Life & Growth: Educational Reimbursement, EAP, Dependent Care. At The Shyft Group, we don't just offer benefits-we invest in your well-being. Join us and experience the difference! Who we are: The Shyft Group is the North American leader in specialty vehicles, including last-mile delivery vans, work trucks, and motorhome chassis. Our 10 brands- Utilimaster, Blue Arc, Royal Truck Body, DuraMag, Magnum, Strobes-R-Us, Spartan RV Chassis, Red Diamond, Builtmore and Independent Truck Upfitters-are powered by 3,000+ team members across the U.S. and Canada. Backed by 50 years of innovation and a supportive, entrepreneurial culture, we're leading the way in electrification and proudly ranked among Fortune's 100 Fastest Growing Companies. Equal Employment Opportunity (EEO) The Shyft Group is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, religion, color, national origin, sex, sexual orientation, gender identity, age, genetic information, status as a protected veteran or status as a qualified Individual with a Disability, or any other characteristic protected by applicable federal, state or local law. If you have a disability and would like to request an accommodation in order to apply, please email us at *************************. The Shyft Group is an E-Verify Employer Shyft uses E-Verify, which is an online system operated by the U.S. Department of Homeland Security in partnership with the Social Security Administration to verify employment eligibility and validate social security numbers. Through participation in the E-Verify program, information entered on Form I-9 will be provided and compared to information available at both of these agencies. See posters for more details. E-Verify Notice U.S. Right to Work Notice.

QC Lab Technician - Lebanon, PA Hours are 7:00am - 3:00pm Monday thru Friday. The employee is expected to be proficient in the duties of the Quality Control Technician position as they appear below. It is also expected that the employee will have read and understand all Brentwood Industries policies and procedures for their intended position Employees may perform other related duties as required to meet the ongoing needs of the organization. Essential Responsibilities: Ensure the safe operation of all equipment during their shift. Know the location of all safety stops. Obtain probed regrind samples from appropriate departments and insure traceability. Know the proper technique of cleaning the lab mil and essential housekeeping duties. Produce a quality lab mil sample from regrind samples and provide these samples for inspection by a qualified quality control lab technician. Communicate all probing and sample preparation in a timely and concise manner. Test roll samples for proper gauge and determine pass/fail results based on pre-determined standards. Report excessively high or low gauge results to the lab lead and/or lab supervisor and also to calender operators. Prepare documentation for testing of roll stock samples. Complete testing of roll stock samples. Cut leaf strips from roll samples and press them into bars for testing. Prepare bars for testing including sanding flash. Conduct impact tests on roll samples and determine pass/fail results based on pre-determined standards. Perform specific gravity on specimens obtained from roll samples collected from the calender lines. Communicate results of all testing in a timely and concise manner. Set up and conduct the following ASTM tests with assistance: ASTM D790 Flexural testing ASTM D882 Tensile testing ASTM D792 Specific gravity testing ASTM D5420 Impact resistance testing ASTM D4226 Impact resistance testing ASTM D648 Heat Deflection Shrinkage/Stretch testing Essential Skills: EDUCATION and/or EXPERIENCE: High school diploma or equivalent preferred. LANGUAGE SKILLS: The ability to read, write (print legibly), speak and understand the English language at the high school level is required. The ability to communicate with other members of the Quality Control and Production departments and understand instructions, either verbal or written, is essential. MATHEMATICAL SKILLS: The ability to add, subtract, multiply, divide and calculate the average of numbers to the fourth decimal place is required. The ability to read digital micrometers and digital calipers as well as various other dial gauges and measuring devices is essential in order to perform the required duties listed above. REASONING ABILITY: The ability to ascertain the pass/fail status of a roll based on standards set forth in instructions whether verbal or written is imperative. The ability to grasp the concept that the end of a roll sample is the core of the next roll and determine the ramifications of that concept as they effect the status of the roll that follows is required. OTHER: By the completion of the 65 day trial period, the individual must possess or have developed most of the skills necessary to complete each duty satisfactorily. The employee must have developed a working knowledge of the Quality Control department and its function within the company. The employee must begin developing a working knowledge of all quality control software used in the lab. Brentwood offers professional growth potential, a pleasant work environment, and an excellent wage and benefits package including 401k w/employer match. Brentwood Industries, Inc., provides equal employment opportunities to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, disability, or genetics. At Brentwood, we have a passion for both our products and our people. Our goal as an employer is to help you excel as an individual and as part of a team by providing you with satisfying, motivating, and stimulating work experience. The varied nature of the environment at Brentwood allows you to work alongside industry professionals on a wide range of projects, contributing your knowledge and strengths to develop innovative, market-driven solutions. Please note: We are not working with external recruiters at this time and are not accepting unsolicited resumes.

Job Description Quality Technician Day Shift: work 2 days, off 2 days, work 3 days, off 3 days (6am to 6pm) Pay: $22.50/hr. with increase opportunities after 120 days Requirements: 1-2 years of experience with quality experience; preferably within the printing, food, or regulated industry with knowledge of GMP's (21CFR 110/111/210/211) Proficiency in Microsoft Office suite is essential Excellent communication skills, both verbal and written Excellent time management skills Attention to detail is essential Ability to work rotating shift 2-2-3-3; including weekends when scheduled Prior experience in the food environment is beneficial Ability to walk, stand, sit, stoop, bend, twist and lift up to 50 pounds. Job Functions: Responsible for monitoring and identifying critical control points (CCP) within the processes. Responsible for monitoring processes and product food safety and quality throughout the manufacturing process. Responsible for the correct documentation and filing of all relevant record logs and Documentation. Ensures the correct recipe guidelines for products are met during processing. Ensures employees are following all Food Safety and worker safety practices. Ensures and educates employees on quality expectations. Collect product samples for the Quality lab. Perform inspections on in-process printing to ensure quality and accuracy of the print according to customer specifications. Identifying non-conformances and ensuring they are corrected “real time” when feasible. Working directly with Operations on the presses, slitter, lamination, etc. to identify areas for continuous improvement. Ensuring paperwork is accurate and filled out in a timely manner on the production lines. The above duties and responsibilities are representative of the nature and level of work assigned and are not necessarily all-inclusive. Benefits: Medical, dental, vision, and prescription drug coverage 401(k) plan with generous company match Bonus program Paid vacation and personal days Paid holidays Company-paid life and AD&D insurance Company paid short-term disability coverage Employee Assistance Program (EAP)

Experienced quality technicians needed on 1st shift. Must have experience and know how to read blueprints. Great starting pay!

C-P Flexible Packaging is now hiring Day Shift Quality Technician 7am-7pm 2/2/3 rotation $22/hour to start (DOE) WHAT YOU GET: Up-to 96 Paid Vacation hours 10 Paid Holidays per year Shoe Reimbursement at 6-months Perfect Attendance Bonus twice a year Other Benefits: Spot Awards Medical, dental, vision, and prescription drug coverage 401(k) plan with generous company match Bonus programs Company-paid life and AD&D insurance, and short-term disability coverage Employee Assistance Program (EAP) Job Functions & Responsibilities (include but are not limited to): Responsible for monitoring and identifying critical control points (CCP) within the processes. Responsible for monitoring processes and product food safety and quality throughout the manufacturing process. Responsible for the correct documentation and filing of all relevant record logs and Documentation. Ensures the correct recipe guidelines for products are met during processing. Ensures employees are following all Food Safety and worker safety practices. Ensures and educates employees on quality expectations. Collect product samples for the Quality lab. Perform inspections on in-process printing to ensure quality and accuracy of the print according to customer specifications. Identifying non-conformances and ensuring they are corrected “real time” when feasible. Working directly with Operations on the presses, slitter, lamination, etc. to identify areas for continuous improvement. Ensuring paperwork is accurate and filled out in a timely manner on the production lines. The above duties and responsibilities are representative of the nature and level of work assigned and are not necessarily all-inclusive. Qualifications: Preferred 1-2 years' experience in printing, food, or regulated industry with knowledge of GMP's (21CFR 110/111/210/211). Proficiency in Microsoft Office package software is essential. Excellent communication skills, both verbal and written Excellent time management skills. Excellent attention to detail is essential. Other knowledge, skills, and abilities: Self-motivated with proven leadership skills. Prior experience in food environment a plus. Must be able to work in a team environment. Ability to work effectively under pressure, and in a fast-paced deadline-oriented environment. Flexible availability: we work night and weekend shifts. Ability to work well in a team environment. Must be able to adapt to changes in the work environment, manage competing demands and be able to deal with frequent change, delays, or unexpected events. Must be able to make immediate decisions on disposition. Must be dependable and work within Company conduct standards; consistently at work and on time, follows instructions, responds to management direction, and solicits feedback to improve performance. Physical Demands: Able to lift to 50-80 lbs. Ability to stand/walk for long periods of time Bending, reaching, twisting, and climbing ladders Ability to work with high temperature materials Ability to work with chemicals for cleaning

Principal Purpose of the Position (2nd Shift - With Occasional 3rd-Shift Coverage): • Maintains the quality control of our product through all stages of the manufacturing process.• Conducts routine inspections and provides support to operators in need of quality assurance while performing daily job duties & customer orders.• Performs daily product inspections in all departments of the manufacturing facility.• Performs daily work area inspections and completes the Quality Dept. Inspection.• Conducts routine services to all units involved in the chemical analysis of the material.• Verifies the daily set up of the eddy current machines.• Maintains customer orders by testing finished product samples.• Works with manufacturing to ensure quality of product and standards.• Performs all other duties and special projects as assigned. Position Qualifications & Requirements: Education: • High School Diploma or GED Experience: • Minimum of 1 year experience in manufacturing plant preferred. Skills and Abilities: • Must train and qualify to use micrometers & calipers.• Must train and qualify on all of the following:o Grain size analysiso Tensile, Yield and Elongation Testingo Rockwell Hardness Testingo Cleanness Testing of LWCo Micrometer Dimensional Inspectiono Dimensional Inspection - AutoCAD Microscopeo Visual Inspections of each work station including measurementso Spectrometer Analysis + Calibration + Serviceo Gas Analyzer Analysis + Calibration + Serviceo Burst/Pressure Testingo Eddy Current Testing including set up and troubleshootingo Cut and prepare test sampleso Must be familiar with power tools: table saw, band saws, polishing wheels, & lathes• Must gain knowledge of ISO 9001 - current standard.• Computer programs: SAP, Microsoft Office, Access, SQL, Excel & Word.• Must gain knowledge of Copper Tube production process: casting, drawing, finishing, annealing.• Must gain knowledge of product testing: grain size analysis, microscope, chemical analysis, tensile testing, Rockwell hardness testing, Eddy Current Testing, Dimensional Measuring, Oxygen & Hydrogen Gas Analysis, Cleanness testing.• Must gain knowledge of Equipment Calibrations and data basing.• Must be willing to work weekends when required. Overtime is required. • This position is assigned to 2nd shift and may be required to cover 3rd shift as needed. Supervisory Responsibilities: • None. Physical Demands and Work Environment: • Fast-paced working environment, extremely hot at times; must always wear hearing, eye, & foot protection. Position is inside a manufacturing facility with a casting & annealing furnace, heavy machinery, cranes, & forklifts.• Must be able to walk extensively during the workday and stand for extended periods of time.• Must be able to wear required Personal Protective Equipment (PPE) for extended periods.• Computer work. Travel: • None.

The Quality Technician plays a critical role in ensuring product integrity and compliance with regulatory and company standards. This position is responsible for performing detailed inspections, testing, and documentation to support food safety, customer satisfaction, and continuous improvement initiatives. The ideal candidate is detail-oriented, proactive, and passionate about maintaining high-quality standards in a fast-paced, regulated environment. Essential functions * Performs CCP verifications * Completes COA's needed for each day's shipments * Performs quality checks and enters data into database. * Enters data into supplier sites (United/Ingridion etc.) * Observe and perform pre operation inspections * Assists in customer complaints and investigations * Calibrates lab equipment and instruments per schedule * Handle customer sampling requests as per customer schedule * Handle sales sample shipments to support new business efforts. * Places all non-conforming products on hold and notifies team and management * Understands product flow and production equipment. * Identifies areas to reduce waste, rework, and other inefficiencies with a focus on continuous process improvement * Maintains overall cleanliness and housekeeping of the lab. * Conducts inventory of supplies and re-stocks the lab. * Trains production team members to perform analytical tests and data entry of results * Performs accurate microbiology testing using approved methods. * Performs and interprets microbiological tests, generates, and maintains accurate/legible/understandable lab data. * Initiates product hold process when product contamination is noted and completes re-sampling/retesting process * Follows SOP's/work instructions for all testing methods to ensure accurate, repeatable results * Reviews SOPs/Policy for accuracy, compliance and effectiveness as per schedule * Conducts internal GMP Audits * Participates in internal audits with audit team, corrective actions and follow up. * Monitors data and production schedule changes to ensure testing is conducted to meet all food safety and quality program testing requirements such as environmental monitoring and equipment hygiene testing, etc. * Contributes to ensuring lab SOPs/procedures are documented, accurate and up-to-date to industry and customer standard testing methods * Properly maintains lab equipment such as pH meters, scales, Refractometers, PLC * Performs other relate duties as assigned Supervisory responsibilities * None Knowledge, Skills and Abilities * Effectively communicates information in one-on-one and small group situations * Ability to follow and implement written or oral instructions. * Ability to problem solve with limited information. * Ability to analyze a situation and investigate root cause. * Critical thinking skills * Basic knowledge of Microsoft Office, an ERP system such as SAP * Ability to read, write and interpret documents in English such as safety rules, operating and maintenance instructions and procedure manuals. * Ability to work with mathematical concepts such as probability and statistical inference, and fundamentals of plane and solid geometry and trigonometry. Ability to apply concepts such as fractions, percentages, ratios, and proportions to practical situations. * Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations. Required education and experience: * High school diploma or GED * Minimum 6 months of quality assurance experience * Ability to obtain HACCP certification (company-sponsored) Preferred education and experience: * AAS or Bachelor's degree in Food Science or related field * Experience in regulated environments (food, pharma) * Familiarity with HACCP, BRC, ISO 9001, FDA, FSIS, USDA standards * Certifications in HACCP, BRC, or ISO 9001 Work environment and physical demands * While performing the duties of this job, the employee is regularly required to stand, walk, sit, use hands, reach with hands and arms, climb or balance, stoop, kneel, crouch, or crawl, and talk/hear, and taste/smell. * The employee must regularly lift and/or move up to 50 pounds. * Specific vision abilities required by this job include close vision, distance vision, peripheral vision, depth perception, ability to see color, and ability to adjust focus. * While performing the duties of this job, the employee is regularly exposed to wet or humid conditions (non-weather), work near moving mechanical parts, work in high, precarious places, fumes or airborne particle, toxic or caustic chemicals, outdoor weather conditions, extreme cold (non-weather), extreme heat (non-weather), risk of electrical shock, vibration, and allergens. * The noise level in the work environment is usually very loud. Benefits include: * Direct deposit paid weekly. * Quarterly performance bonus opportunities! * Affordable health, vision, and dental insurance plans - Eligible 1st day of the month following 30 days of employment. * Free health savings account with employer match. * Fidelity 401(k) with competitive employer match - fully vested from date of hire. * 3 weeks paid time off plus sick time (pro-rated based on start date). * 9 paid company holidays and 3 paid personal holidays. * Boot allowance twice per year. * Protective equipment and company swag provided. * Free life insurance up to $150,000. * Free employer-paid short-term and long-term disability coverages. * Employee Assistance Programs. * And more! Travel required * The home office for this role is indicated at the top of this . Travel to other Ingredients Plus locations may be required as business needs arise. Affirmative Action/EEO statement We are an equal opportunity employer. We do not discriminate on the basis of race, color, creed, religion, gender, sexual orientation, gender identity, age, national origin, disability, veteran status or any other category protected under federal, state, or local law. All employment is decided on the basis of qualifications, merit, and business need. Other duties Please note this job description is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities that are required of the employee for this job. Duties, responsibilities and activities may change at any time with or without notice.

Job DescriptionDescription: Do you have an eye for attention to detail and an impeccable desire to enforce and maintain high standards of Quality? Then look no further and join the Quality Team at Advanced Cooling Technologies, Inc. (ACT) - nominated as a “Best Places to Work” in PA in 2023, York location. The Quality Team ACT is looking for team members who are passionate about creativity and innovation and looking to make a difference every day. We are committed to developing world class Quality Assurance programs, processes, and people that support the ACT mission and family of brands, including Tekgard Environmental Control Units. We have an immediate opening for a Quality Inspection in our York location. Company Overview Advanced Cooling Technologies, Inc. (ACT), with locations in York and headquartered in Lancaster, PA, is a leading manufacturer of innovative thermal management products for diverse applications, serving a broad spectrum of industries including commercial satellites, military vehicles, medical devices, primary calibration equipment, and HVAC systems. We are dedicated to fostering creativity, innovation, and making a tangible difference every day. Our commitment extends to our customers, employees, and community, with core values centered on Innovation, Teamwork, and Customer Care-key drivers of our continuous growth and success. At ACT, our skilled and dedicated staff is our most valuable resource. ACT offers a robust benefits package including low-cost medical, dental, vision, company-paid life and disability insurance, paid time off, a 401k with company match, and a profit-sharing bonus plan. Enjoy a work-life balance at our York location supported by a 4-day work week (4/10 schedule), generous PTO, and 8 paid holidays. Position Summary This position is for a Quality Inspector at our facility located in York, PA. As a Quality Inspector, you will play a hands-on role within the organization and interface with both Operations and Product Development teams while performing incoming inspection of materials and components and performing in-process and final inspections of products for commercial and/or government customers. Key Duties and Responsibilities Inspect incoming materials Perform in-process inspections and/or final inspections on manufactured product Ensure all materials and product meet Quality standards as per policy and ISO9001/AS9100 procedures Identify and segregate non-conformances and write non-conformance reports Support Supplier Quality initiatives ACT is an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to race, religion, color, national origin, sex, sexual orientation, gender identity, age, status as a protected veteran, status as a qualified individual with a disability, or any other trait protected by law. Requirements: High School Diploma or GED Ability to read and interpret blueprints and shop drawings Ability to use basic inspection tools such as micrometers, calipers, height gages, etc. Basic computer skills (Outlook, Word, Excel). Basic math skills Strong verbal and written communication skills Additional Qualifications (preferred): Authorized to work in the US. US Citizen, Permanent Resident, or Protected Individual (as defined by 8 U.S.C. § 1324b(a)(3)) preferred due to ITAR responsibilities. Prior experience with ERP systems

Quality Technician Day Shift: work 2 days, off 2 days, work 3 days, off 3 days (6am to 6pm) Pay: $22.50/hr. with increase opportunities after 120 days Requirements: 1-2 years of experience with quality experience; preferably within the printing, food, or regulated industry with knowledge of GMP's (21CFR 110/111/210/211) Proficiency in Microsoft Office suite is essential Excellent communication skills, both verbal and written Excellent time management skills Attention to detail is essential Ability to work rotating shift 2-2-3-3; including weekends when scheduled Prior experience in the food environment is beneficial Ability to walk, stand, sit, stoop, bend, twist and lift up to 50 pounds. Job Functions: Responsible for monitoring and identifying critical control points (CCP) within the processes. Responsible for monitoring processes and product food safety and quality throughout the manufacturing process. Responsible for the correct documentation and filing of all relevant record logs and Documentation. Ensures the correct recipe guidelines for products are met during processing. Ensures employees are following all Food Safety and worker safety practices. Ensures and educates employees on quality expectations. Collect product samples for the Quality lab. Perform inspections on in-process printing to ensure quality and accuracy of the print according to customer specifications. Identifying non-conformances and ensuring they are corrected “real time” when feasible. Working directly with Operations on the presses, slitter, lamination, etc. to identify areas for continuous improvement. Ensuring paperwork is accurate and filled out in a timely manner on the production lines. The above duties and responsibilities are representative of the nature and level of work assigned and are not necessarily all-inclusive. Benefits: Medical, dental, vision, and prescription drug coverage 401(k) plan with generous company match Bonus program Paid vacation and personal days Paid holidays Company-paid life and AD&D insurance Company paid short-term disability coverage Employee Assistance Program (EAP)

(2nd Shift - With Occasional 3rd-Shift Coverage): • Maintains the quality control of our product through all stages of the manufacturing process. • Conducts routine inspections and provides support to operators in need of quality assurance while performing daily job duties & customer orders. • Performs daily product inspections in all departments of the manufacturing facility. • Performs daily work area inspections and completes the Quality Dept. Inspection. • Conducts routine services to all units involved in the chemical analysis of the material. • Verifies the daily set up of the eddy current machines. • Maintains customer orders by testing finished product samples. • Works with manufacturing to ensure quality of product and standards. • Performs all other duties and special projects as assigned. Position Qualifications & Requirements: Education: • High School Diploma or GED Experience: • Minimum of 1 year experience in manufacturing plant preferred. Skills and Abilities: • Must train and qualify to use micrometers & calipers. • Must train and qualify on all of the following: o Grain size analysis o Tensile, Yield and Elongation Testing o Rockwell Hardness Testing o Cleanness Testing of LWC o Micrometer Dimensional Inspection o Dimensional Inspection - AutoCAD Microscope o Visual Inspections of each work station including measurements o Spectrometer Analysis + Calibration + Service o Gas Analyzer Analysis + Calibration + Service o Burst/Pressure Testing o Eddy Current Testing including set up and troubleshooting o Cut and prepare test samples o Must be familiar with power tools: table saw, band saws, polishing wheels, & lathes • Must gain knowledge of ISO 9001 - current standard. • Computer programs: SAP, Microsoft Office, Access, SQL, Excel & Word. • Must gain knowledge of Copper Tube production process: casting, drawing, finishing, annealing. • Must gain knowledge of product testing: grain size analysis, microscope, chemical analysis, tensile testing, Rockwell hardness testing, Eddy Current Testing, Dimensional Measuring, Oxygen & Hydrogen Gas Analysis, Cleanness testing. • Must gain knowledge of Equipment Calibrations and data basing. • Must be willing to work weekends when required. Overtime is required. • This position is assigned to 2nd shift and may be required to cover 3rd shift as needed. Supervisory Responsibilities: • None. Physical Demands and Work Environment: • Fast-paced working environment, extremely hot at times; must always wear hearing, eye, & foot protection. Position is inside a manufacturing facility with a casting & annealing furnace, heavy machinery, cranes, & forklifts. • Must be able to walk extensively during the workday and stand for extended periods of time. • Must be able to wear required Personal Protective Equipment (PPE) for extended periods. • Computer work. Travel: • None.

US Tech Solutions is a global staff augmentation firm providing a wide-range of talent on-demand and total workforce solutions. To know more about US Tech Solutions, please visit our website ********************************** are constantly on the lookout for professionals to fulfill the staffing needs of our clients, and we currently have a job opening that may interest you Job Description Title: Quality control chemist- 2nd shift Duration: 12 Months Location: Myerstown, PA 17067 Description: The Raw Material testing team is responsible for Quality Control testing of APIs and excipients used in the manufacture of pharmaceutical and nutritional products. This is a fast-paced, energetic team that works together across two shifts to meet aggressive throughput times to support a lean manufacturing operation. Position Summary: In this position, the incumbent will be expected to draw upon previous analytical experience, as well as continuously learn Quality Control systems and effectively engage in relationships with peers in the laboratories, Manufacturing/Production, and personnel in other departments as needed. The incumbent will perform analysis on raw materials following prescribed procedures to provide the information base leading to material disposition, as well as assist in troubleshooting and problem solving as directed. Once the incumbent is assigned specific materials on which to perform the quality control tests, or provide development or troubleshooting, the incumbent will have considerable impact on results from his/her work. Material can be rejected and manufacturing procedures can be altered significantly either in schedule changes or in process itself. Position Duties & Responsibilities : Perform standard qualitative and quantitative analysis: • Utilize standard analytical chemistry techniques: wet analytical methods, HPLC, UV, GC, AA, polarimeter, FT-IR, NIR, RAMAN, etc.) to test raw materials in accordance with approved testing procedures, including those from company, the National Formulary (NF), the United States Pharmacopoeia (USP), the European Pharmacopoeia (EP), and the FDA. • Properly document and maintain records of all analysis information of assigned materials on data sheets and laboratory notebooks for permanent file. • Evaluate all data obtained from analysis; if discrepancy or deviation occurs, consult with Supervisor and recommend additional testing if necessary. • Communicate to supervision in a timely manner all non-compliance situations, and assist in investigations. • Assist with troubleshooting analytical methodology and instrumentation malfunctions. • Perform special assignments as directed by supervisor, for example, revise existing analytical testing monographs to comply with compendia changes or other specific needs. • Accurate, complete and timely fulfillment of the job responsibilities will, in part, ensure GMP compliance as outlined in various Bayer and U.S. government rules and regulations. Documentation Review: • Review testing documentation performed by other analysts for compliance with BAYER, FDA, National Formulary (NF), United States Pharmacopoeia (USP), and European Pharmacopoeia (EP) procedures. Safety: • Adhere to the pertinent aspects of Corporate and plant safety programs and adhering to GMP's, ISO standards or other regulations. Qualifications Requirements/Preferences: • Bachelor's degree in Chemistry, Biology, Pharmacy, or related 4 year science degree required. Chemistry degree is preferred. • At least 1-3 years of experience in a GMP laboratory environment. Master's degree in a related field with 1 year of experience may be considered. • Knowledge, practical application, and understanding of analytical chemistry is required to perform the functions of this position. • Basic experience with Personal Computer (PC). • Demonstrated capability for communicating ideas, concepts, and work results effectively to colleagues and supervision. • Demonstrated ability to be self-motivated as well as to work collaboratively in a team-based environment is required. • Must demonstrate initiative and a willingness to learn. • Good working knowledge of advanced laboratory instrumentation and personal computer skills are required. • Good working knowledge of advanced laboratory instrumentation and computers are required; This is defined as strong troubleshooting skills for assigned area such as HPLC, GC, AA, UV, TOC, NIR and/or dissolution and low error rates with microbiology or chemistry techniques for defined area • A working knowledge of organic chemistry, statistics, data processing and good manufacturing practices is required • Demonstrated ability to clearly communicate technical information in writing required. • Demonstrated ability to manage key projects and display area of expertise; i.e. clear/consistent notebook skills and function as an independent worker. • Demonstrated ability to be self-motivated as well as to work collaboratively in a team-based environment is required. • Demonstrated ability to take initiative and display a willingness to learn required. • A thorough understanding of National Formulary (NF); United States Pharmacopeia (USP); and European Pharmacopeia (EP) testing procedures, as well as, US Pharmaceutical Industry Good Manufacturing Practices (GMP's), quality control methods and procedures is required. • Competencies required: analytical problem solving, alertness, work within established policies and procedures, commitment to task, decisiveness, effective written and interpretive communication skills, and organization and planning skills. • Enter here Travel Requirements: None Thanks & Regards, Mayank Gupta, (M. Pharmacy) (Lead Pharma Technical Recruiter) Additional Information All your information will be kept confidential according to EEO guidelines.