Welder fitter jobs in Corpus Christi, TX - 44 jobs

**Requisition ID: 177768** Assembles and fits to drawing dimensions of all kinds of structural, plate and mechanical materials into all types of assemblies. **Experience Level** Intermediate - Read blueprints, section and plan drawings, and weld symbols to derive measurements, dimensions, and quantity of material needed to fabricate a structure. - Unload, sort, and stack heavy steel pieces, then hoist each one into the proper place for fastening. - Fabricate, assemble, and install structural steel products such as beams, braces, pipes, and plates for jackets and decks - Lay out and fit pipe, beams, decks and jackets; frame skids, bends, and elevations for jackets; cut plate, pipe, and beams using a cutting torch. - Use Come-a-longs, chain falls, and other industry tools and equipment, and install, use, and remove stop plates, dogs, and pad eyes **Qualifications** - May require a high school diploma or its equivalent with previous years of experience in the field or in a related area. - Must possess strong working knowledge skills and abilities for position. - Ability to understand, follow and transmit written and oral instructions and communicate effectively with management/supervision. - Proficient in the safe and efficient use of electrical, hand tools, power tools and layout tools as well as measurement tools **Requirements** - Able to meet all physical requirements. - Must have all required tools - Expected to climb and work at heights and in confined spaces (may exceed 200 ft) - Able to work outdoors in all weather conditions - Able to work overtime, nights, and weekends as required by the workload - Observe and comply with all safety and project rules. Performs other duties as required. Equal Opportunity Employer, including disability and protected veteran status. Company: Kiewit_Craft

Assembles and fits to drawing dimensions of all kinds of structural, plate and mechanical materials into all types of assemblies. Experience Level 1st Class Must have the ability to read blueprints, section and plan drawings, and weld symbols to derive measurements, dimensions, and quantity of material needed to fabricate a structure. Unload, sort, and stack heavy steel pieces, then hoist each one into the proper place for fastening. Fabricate, assemble, and install structural steel products such as beams, braces, pipes, and plates for jackets and decks Lay out and fit pipe, beams, decks and jackets; frame skids, bends, and elevations for jackets; cut plate, pipe, and beams using a cutting torch. Use Come-a-longs, chain falls, and other industry tools and equipment, and install, use, and remove stop plates, dogs, and pad eyes. Estimating sizes, distances, and quantities; or determining time, costs, resources, or materials needed to perform a work activity. Inspect subordinate's work for compliance with the contract plans and specifications, point out deficiencies and explain and take any corrective action needed. Qualifications May require a high school diploma or its equivalent with previous years of experience in the field or in a related area. Must possess strong working knowledge skills and abilities for position. Ability to understand, follow and transmit written and oral instructions and communicate effectively with management/supervision. Proficient in the safe and efficient use of electrical, hand tools, power tools and layout tools as well as measurement tools. Requirements Able to meet all physical requirements. Must have all required tools Expected to climb and work at heights (may exceed 200 ft) and in confined spaces. Able to work outdoors in all weather conditions. Able to work overtime, nights, and weekends as required by the workload Observe and comply with all safety and project rules. Perform other duties as required. Labor One Staffing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national or ethnic origin, sex, sexual orientation, gender identity or expression, age, disability, protected veteran status or other characteristics protected by law.

Description:Offshore Fitter Job Description ** Offshore Fitter **Department:** Offshore **Employment Type:** Full-time The Offshore Fitter is responsible for accurately laying out, cutting, and fitting piping, vessel, and structural components based on supplied drawings or field-verified dimensions. This position requires offshore construction experience, physical capability, and a strong commitment to quality, productivity, and safety. The Fitter must maintain professionalism, show up on time, and work effectively with helpers, riggers, and welders. Key Responsibilities Figure material take-offs on drawings for required cut lengths. **Use pipe cutting machine, or if unavailable, use beveling machine to cut pipe to required length. Communicate with helper/rigger to identify needed material or equipment for each task. **Align parts using jacks, turnbuckles, wedges, drift pins, pry bars, and heavy hammers. Mark reference points on floor or face block and transpose them to workpiece using measuring devices, squares, chalk, and soapstone. Give instructions to welders to build up low spots or short pieces with weld. **Straighten warped or bent parts using sledge, hand torch, straightening press, and push-pull methods. **Remove high spots and cut bevels using hand files, portable grinders, and cutting torch. Examine blueprints and plan work sequence, applying knowledge of geometry, weld shrinkage, machining, and metal thickness. **Assemble and secure pipes, tubes, fittings, and related equipment using welding, brazing, cementing, soldering, and threading joints. Label all information on pipe before cutting; transfer item numbers onto cut sheet and carry them over to drop pipe. Inspect and test installed systems and pipelines using pressure gauges, hydrostatic testing, observation, or other methods. **Ascend/descend stairwells frequently with or without tools and equipment. Plan pipe system layout, installation, or repair per specifications. Read and understand blueprints and ISOs. **Demolish and install handrails and grating on platform. Verify all measurements, checking for square and level before releasing to welder. Note pre-weld dimensions on fitter drawings. **Hang and swing on vertical rope to/from platform and boat (potential rough seas/wind). Ensure all fabricated items are tagged with the correct job number, customer name, and piece number. **Climb and work from heights. **Pull tools and equipment up/down to workstations or areas. Show up to work on time and as scheduled. Inspect all equipment daily (torch, torch hoses, grinder, levels, tapes, etc.). Maintain a clean and safe work area by sweeping as needed. Complete and discuss a thorough Job Safety and Environmental Analysis (JSEA) prior to each task. Maintain a positive attitude toward customers and represent ACI professionally. What You Need to Know Preferably 2 years minimum experience in fitting (piping, vessel, and structural) fabrication. Minimum of 2 years recent offshore construction experience. Most recent offshore experience within the last 4 years. Ability to read and interpret ISOs and blueprints. Familiarity with offshore emergency response, escape procedures, and water survival skills. HSE Responsibilities Embrace, lead, and demonstrate “Acadian F.I.R.S.T.” - Vision & Mission Statement as fundamental core values. Demonstrate visible leadership and support proactive safety processes (JSA, Time Out & TEAM BBS Observations) to achieve an incident-free workplace and advance our safety culture. Adhere to all Health, Safety & Environmental (HSE) Management System policies, procedures, safe work practices, and client-specific regulatory requirements. Make a personal commitment and be accountable for HSE results, driving toward the achievement of defined goals. Clearly communicate these goals through direct reports, while coaching, mentoring, and empowering others to achieve desired outcomes. Conduct periodic quality assessments of HSE processes to enhance personal coaching and mentoring effectiveness and demonstrate ownership in the successful implementation of HSE programs. Requirements:

About Us We have earned a reputation for leading the industry in turnarounds, specialty welding, construction, pipe fabrication, and maintenance. Backed by a team of talented supervisors and craft professionals, we are prepared to tackle the toughest jobs for clients in the refining, chemical, petrochemical, renewables, and midstream industries. Job Summary Combination Welders must have industrial welding experience in a petrochemical or related industrial fabrication facility. Welders having the ability to read and interpret blueprints, ISO's, field drawings, and material takeoffs a plus. Welders will perform a range of duties which will include but is not limited to welding various metals using processes such as SMAW, GMAW, FCAW, and GTAW. Welders are responsible for selecting, setting up, and staging the proper equipment for their jobs and that each are in ample supply and working order. This includes welding machines, gases, tools, and other consumables. Welders are also responsible for double checking the fit of pipe or other structural pieces and to allow for proper attachment. Attention to safety and detail are of the utmost importance. Welders must successfully pass pre-employment weld tests as part of the on-boarding process. Requirements Industrial Combo welding experience with GTAW and SMAW. Must pass GTAW & SMAW manual welding procedures test. Current Basic Orientation Plus (Safety Council Card) or within 3 months expiration. Current TWIC card Have three (3) or more years' experience in your craft. Compliance with designated welding procedures and specifications. Follow established job-site safety and work regulations, as well as maintaining a safe and clean work area. Identify safety hazards you or other employees may be subject to and take all necessary corrective action to eliminate or minimize hazards. Use appropriate hand and power tools to properly measure, cut, assemble, weld and install all types of pipe and/or similar tubular products; install supports, valves and other control equipment; test installed piping systems and install all other related items in accordance with the applicable plans and specifications; bolt, clamp or weld parts to secure in position for welding; weld components according to specific process and code. Produce quality work, meeting requirements of plans, specifications and industry standards. Physical Requirements Significant and sustained periods of standing, walking, bending, squatting and lifting. Good communication skills (speaking and actively listening) with co-workers and supervisors. Must have good manual dexterity to perform precision adjustments of machinery parts and controls. Will use arms and hands to signal, grab, hold, turn, push, and pull: objects, materials, controls and tools. May be required to lift, carry and move up to 50lbs. Will work at heights, climb ladders and stairways and work off of platforms. Will work at heights up to 300' utilizing proper fall protection. Will use vision abilities to focus, see short and long distances, colors, depth perception and peripheral vision. Must be capable of working outside in the elements including but not limited to the heat, cold, rain, snow and wind; and must be able to work for long period of times up to 12 hours a day. Will be required to wear personal protective equipment (PPE) including but not limited to: hard hat, safety glasses/goggles, ear plugs/muffs, masks/respirators, safety vests, gloves and steel-toe boots. We offer our employees a competitive salary and comprehensive benefits package and are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled Notice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here. Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent. #REPCON Equal Opportunity Employer As a leading provider of mechanical and electrical construction, facilities services, and energy infrastructure, we offer employees a competitive salary and benefits package and we are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled Notice to Prospective Employees Notice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here. Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent.

Industrial Air Flow Dynamics, Inc. is now hiring for our Spring Season! (March - June) We've Got the Gear, the Travel, and the Pay - Just Bring the Skill At Industrial Air Flow Dynamics, Inc., we know great welders don't just need a paycheck, they need support. That's why we supply all the tools and PPE required for each job, cover your travel and hotel, pay you for passing your weld test, and even reward you for bringing your friends along. When you work with us, you're not just another name on a roster. You're part of the crew that keeps America's power plants running. We're hiring experienced Stainless Steel Structural Welders (Flux-Core Process) for long term, nationwide turnaround work. If you're dependable, driven, and ready to get paid to travel, read on. Why Weld with Us? Tools & PPE Provided - No need to haul your gear. We've got it covered. Travel Covered - We pay your airfare and provide shared hotel accommodations. Daily Per Diem - $30/day to cover meals and incidentals. Referral Bonuses - Know someone who's got what it takes? Get paid when we hire them. Fair Pay - $25/hour + $15/hour paid while you travel time to the project The Job You'll travel across the U.S. to power plant sites, welding stainless steel structural components using the Flux-Core process (309 wire on ½" carbon plate). You'll read and work from detailed blueprints, and perform 2G, 3G, and 4G welds in all positions including overhead and vertical, in high-pressure, physically demanding environments like boilers and scaffolding systems. What We're Looking For 3+ years of industrial welding experience Ability to pass bend-tested welds: 2G, 3G, and 4G (Flux-Core, 309 wire) Comfortable working at heights and in tight, hot spaces Willing to travel continuously nationwide Strong work ethic, blueprint reading skills, and commitment to safety Pay & Benefits $25/hour base pay + $15/hour travel pay + $30/day per diem Paid airfare + hotel accommodations Rental car provided (must have valid driver's license) Referral bonuses when your referrals get hired Full Benefits Package Includes: Safe Harbor 401(k) Medical, Dental & Vision coverage Life, AD&D, Short & Long-Term Disability options Quick, No-Nonsense Hiring Process Our application is simple and fast. No long forms, no fluff. Just tell us who you are, where you've worked, and how to reach you. If it's a match, we'll reach out from an 281 area code. Next Steps: Phone screening Weld test (with clear instructions) Drug Test If you're a skilled welder who wants to travel the country, earn great pay, and work with a team that has your back, this is your chance. Apply now and bring your skills to the job. We'll handle the rest!

Job Description No teaching experience required, we will provide all necessary tools and training to succeed!! Full and part-time available We call it being a life changer, but you'll call it a job you love while helping others find the same. You'll have a hand in improving the lives of countless SCI students throughout Texas by working with impassioned educators and campus faculty in a collaborative, interactive environment to create optimized environment for our students. Responsibilities Demonstrates and applies a thorough and accurate knowledge of the teaching field and discipline; Plans and organizes instruction in ways which maximize student learning. Practice excellence in teaching and instruction; Modifies instructional methods and strategies to meet diverse students' needs; Prepare lesson plans and teach course as prescribed by the approved institutional curriculum; Encourages the development of communication skills and higher order thinking skills through appropriate assignments. Requirements Minimum of 3 years of industry experience preferred; Prior post-secondary related teaching experience of at least 1 year in subject matter is highly preferred; Certified AWS and/or NCCER. Benefits Training & Development Fun & Energetic, Family-Based Environment Continuous Growth Opportunities Medical, Dental, & Vision Options Health Savings & Flexible Spending Options (HSA & FSA) Basic Life & Accident Insurance Short & Long-term Disability 401K Retirement Plan SCI is an Equal Opportunity employer. About Southern Careers Institute SCI has been changing lives for over 60 years, now and we're just getting started. We offer certification-based training with programs in Medical, Business, Cosmetology, Skilled-Trades and Technology with campuses spanning across central and south Texas as well as online. Our students can graduate most of our programs in under one year and with real-world experience under their belt.

Project Details: Pipe Welder Shop and ships Essential Duties and Responsibilities: Other duties may be assigned. A welder must understand welding procedures and parameters. Can comprehend and utilize blueprints, sketches, drawings, technical. Manuals, gouge, and work process instruction. Welds steel plates and pipes in the repair and/or construction of marine vessels, industrial components, and associated equipment. Have the skills to use various types of welding equipment for different types of metal. Welds components in a flat, vertical, or overhead position. Performs related tasks such as cutting and grinding. Repairs broken or cracked parts, fills holes, and increases the size of metal parts. Welds metal parts together using gas welding, brazing, arc welding, wire fed welding, or tig welding process and procedures. Highly skilled welders often are trained to work with a wide variety of materials, such as titanium, aluminum, or exotic metals, in addition to steel. Select and set up welding equipment, execute the planned welds, and examine the welds to ensure that they meet standards or specifications. Required Education & Experience: High School Diploma, some college or technical school certification, six months to one year(s) experience or equivalent combination of education and experience. Must pass an ABS, or ASME weld test. Working Conditions: Open-air conditions such as noisy, hot, cold, etc. Must be able to stand and operate equipment for up to four continuous hours. You must wear hearing, eye, head protection and proper PPE. Some climbing (100 feet or higher) and lifting (50 lbs.) involved. Working with hot and sometimes hazardous materials. Work on inland and offshore barges or in industrial settings. Enter round manholes with inside diameters of 18”, and other internally confined spaces. Traverse gangways and scaffolding at varying heights. Necessary Equipment Operation: Blow torches- Motorized cutting torches; Pattern cutting torches; Welding torches. Gas welding, brazing, or cutting apparatus- Brazing equipment; Heliarc welding equipment; Oxyacetylene equipment; Portable gas operated arc welders. Manlift or personnel lift- hydraulic truck lifts; Swing stages Welding masks- Hand shields; Welding shields. Special Skills: Ability to work under deadlines and schedule pressures. Ability to read and interpret blueprints, sketches, drawings, and technical manuals. Excellent interpersonal and communication skills. High performance and a strong team player. Commitment to company values and safety program. Welder Position Basic Requirements: Qualifications of class - Class will be based upon judgment by quality control and/or production management in terms of the quality and productivity of the welds. Plate Welder 2nd Class (PLW2) - Welder capable of welding SMAW or FCAW on plate/structural with ABS Q2+4G or ASME or AWS plate test (2G+3G+4G). Plate Welder 1st Class (PLW1) - Welder capable of welding SMAW & FCAW on plate/structural with ABS Q2+4G or ASME or AWS plate test (2G+3G+4G). Pipe Welder 2nd Class (PPW2) - Welder capable of welding SMAW or FCAW on plate/structural &SMAW or FCAW on pipe with ABS Q3 or AWS 6g pipe test. Pipe Welder 1st Class (PPW1) - Welder capable of welding SMAW & FCAW and or GTAW on pipe. Must Pass ABS Q3 or ASME 6G or AWS 6G pipe test. Combination Welder 1st Class- Pipe/Plate/Structural (PPLW)- Welder capable of process / structural pipe and plate welding using GTAW+FCAW and or GTAW+SMAW. Combination Welder 2nd Class- Pipe/Plate/Structural (PPLW)- Welder capable of process / structural pipe and plate welding using GTAW+FCAW and or GTAW+SMAW. the individual responsibility of every employee to maintain a current awareness and understanding of appropriate regulations, internal policies and procedures, and to comply fully with those regulations, policies and procedures. An Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, or protected veteran status and will not be discriminated against on the basis of disability. Equal Employment Opportunity Posters. If you'd like to view a copy of the company's affirmative action plan or policy statement, please email: [email protected]. If you have a disability and you believe you need a reasonable accommodation in order to search for a job opening or to submit an online application, please e-mail: [email protected]. The statements herein are intended to describe the general nature and level of work being performed by employees assigned to this classification. They are not intended to be construed as a comprehensive list of all responsibilities, duties, and skills required of assigned personnel.

No teaching experience required, we will provide all necessary tools and training to succeed!! We call it being a life changer, but you'll call it a job you love while helping others find the same. You'll have a hand in improving the lives of countless SCI students throughout Texas by working with impassioned educators and campus faculty in a collaborative, interactive environment to create optimized environment for our students. Responsibilities * Demonstrates and applies a thorough and accurate knowledge of the teaching field and discipline; * Plans and organizes instruction in ways which maximize student learning. Practice excellence in teaching and instruction; * Modifies instructional methods and strategies to meet diverse students' needs; * Prepare lesson plans and teach course as prescribed by the approved institutional curriculum; * Encourages the development of communication skills and higher order thinking skills through appropriate assignments. Requirements * Minimum of 3 years of industry experience preferred; * Prior post-secondary related teaching experience of at least 1 year in subject matter is highly preferred; * Certified AWS and/or NCCER. Benefits * Training & Development * Fun & Energetic, Family-Based Environment * Continuous Growth Opportunities * Medical, Dental, & Vision Options * Health Savings & Flexible Spending Options (HSA & FSA) * Basic Life & Accident Insurance * Short & Long-term Disability * 401K Retirement Plan * SCI is an Equal Opportunity employer. About Southern Careers Institute SCI has been changing lives for over 60 years, now and we're just getting started. We offer certification-based training with programs in Medical, Business, Cosmetology, Skilled-Trades and Technology with campuses spanning across central and south Texas as well as online. Our students can graduate most of our programs in under one year and with real-world experience under their belt.

OFS Facility Operations | Sub Arc Welder Force Pressure Control is seeking safety-oriented production personnel to work in its Orange Grove facility. Welding personnel must be able to operate with and without supervision, prepare and initiate jobs, maintain machinery and working production area, and record all data outlined in QAQC protocols. Three years working experience within sub arc work scopes is required as is working experience with alloys and API ring grooves. Working background with valve and other wellhead / surface pressure control equipment is valued. Candidates must be able to successfully pass bend test The Sub Arc Welder position is a full time, non-exempt position. Overtime in excess of 40 hours per work week will be required. Hourly pay rate commensurate with experience. Applicants have rights under Federal Employment Laws.

**About Us** We have earned a reputation for leading the industry in turnarounds, specialty welding, construction, pipe fabrication, and maintenance. Backed by a team of talented supervisors and craft professionals, we are prepared to tackle the toughest jobs for clients in the refining, chemical, petrochemical, renewables, and midstream industries. **Job Summary** Combination Welders must have industrial welding experience in a petrochemical or related industrial fabrication facility. Welders having the ability to read and interpret blueprints, ISO's, field drawings, and material takeoffs a plus. Welders will perform a range of duties which will include but is not limited to welding various metals using processes such as SMAW, GMAW, FCAW, and GTAW. Welders are responsible for selecting, setting up, and staging the proper equipment for their jobs and that each are in ample supply and working order. This includes welding machines, gases, tools, and other consumables. Welders are also responsible for double checking the fit of pipe or other structural pieces and to allow for proper attachment. Attention to safety and detail are of the utmost importance. Welders must successfully pass pre-employment weld tests as part of the on-boarding process. Requirements + Industrial Combo welding experience with GTAW and SMAW. + Must pass GTAW & SMAW manual welding procedures test. + Current Basic Orientation Plus (Safety Council Card) or within 3 months expiration. + Current TWIC card + Have three (3) or more years' experience in your craft. + Compliance with designated welding procedures and specifications. + Follow established job-site safety and work regulations, as well as maintaining a safe and clean work area. Identify safety hazards you or other employees may be subject to and take all necessary corrective action to eliminate or minimize hazards. + Use appropriate hand and power tools to properly measure, cut, assemble, weld and install all types of pipe and/or similar tubular products; install supports, valves and other control equipment; test installed piping systems and install all other related items in accordance with the applicable plans and specifications; bolt, clamp or weld parts to secure in position for welding; weld components according to specific process and code. + Produce quality work, meeting requirements of plans, specifications and industry standards. Physical Requirements + Significant and sustained periods of standing, walking, bending, squatting and lifting. + Good communication skills (speaking and actively listening) with co-workers and supervisors. + Must have good manual dexterity to perform precision adjustments of machinery parts and controls. + Will use arms and hands to signal, grab, hold, turn, push, and pull: objects, materials, controls and tools. + May be required to lift, carry and move up to 50lbs. + Will work at heights, climb ladders and stairways and work off of platforms. Will work at heights up to 300' utilizing proper fall protection. + Will use vision abilities to focus, see short and long distances, colors, depth perception and peripheral vision. + Must be capable of working outside in the elements including but not limited to the heat, cold, rain, snow and wind; and must be able to work for long period of times up to 12 hours a day. + Will be required to wear personal protective equipment (PPE) including but not limited to: hard hat, safety glasses/goggles, ear plugs/muffs, masks/respirators, safety vests, gloves and steel-toe boots. **We offer our employees a competitive salary and comprehensive benefits package and are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled** **Notice to prospective employees:** **There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here (****************************************************************************************************** DateDesc&w=&wc=&we=&wpst=) . Please check our available positions to confirm that a post or email is genuine.** **EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent.** **\#REPCON** **Equal Opportunity Employer** As a leading provider of mechanical and electrical construction, facilities services, and energy infrastructure, we offer employees a competitive salary and benefits package and we are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled **Notice to Prospective Employees** Notice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companieslist open positions here (************************************** . Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent. Email a Friend Email a Friend **Job Locations** _US-TX-Corpus Christi_ **ID** _2025-1544_ **Company** _Repcon, Inc._ **Category** _Fabrication_ **Position Type** _Full-Time_ **Location Type** _Onsite_ **Posted Date** _3 months ago_ _(10/15/2025 9:43 AM)_

Job Description Are you a talented welder looking to travel and work on exciting projects across the country? Tanco Engineering wants to hear from you! With over 40 years in the industry, we're proud of our reputation for safety, reliability, and excellence. As a Storage Tank Welder with us, you'll play a critical role in ensuring the quality and safety of storage tanks. You'll join a friendly team that values your skills and contributions while giving you the chance to work in varied locations, meeting new people, and tackling interesting challenges. At Tanco Engineering, we believe in teamwork and open communication. You won't just be a number; you'll be a valued part of our family. So, if you're ready for an opportunity to shine, let's make it happen! Position Duties: Utilize your welding skills to ensure the structural integrity of storage tanks through various techniques like stick and flux core welding. Read and interpret blueprints to ensure your welding tasks meet all specifications. Inspect your work for quality control, promptly addressing any issues you may uncover. Work alongside your team to ensure projects are completed efficiently and on time. Maintain a safe work environment by following all safety protocols. Keep your welding equipment in top shape with routine maintenance and troubleshooting as needed. Requirements At least a year of welding experience, ideally in the storage tank industry. Attention to detail with a skill for spotting potential defects. A willingness to lift heavy equipment and engage in physically demanding tasks. Strong communication abilities coupled with a collaborative spirit. A passion for travel and the flexibility to work in various locations. A TWIC card might be required Be willing to submit to pre-hire, random, and post-incident drug and alcohol testing. Background checks will also be included in the hiring procedure. Must be over 18 and eligible to work in the United States. Benefits Medical, dental, & vision insurance Retirement plan & ESOP Competitive pay with annual reviews. Join our team and enjoy competitive starting pay of $30-$34 per hour, which may vary depending on your experience and the results of your welding test. In addition to the attractive pay range, we offer a subsistence allowance of $125 (exceptions may apply per location) and reimbursement of $0.70 per mile for travel (when applicable).

Labor One Staffing, is looking for Structural Fitters for the Ingleside, TX area. Fitters to build and repair large structures and platforms. Most fabrication will be done with Flux core. Responsibilities: is responsible for performing, with minimal supervision. Steel structural work in all stages of new construction of marine vessels. Qualifications: The position requires a working knowledge of procedures. Strong mechanical aptitude. Ability to read blueprints and be able to follow directions. The individual must possess experience in the trade, knowledge of ship terminology, blueprint reading, and measurements. Ability to interpret job specifications and drawings. The qualifications and general capabilities listed below are representative of the knowledge, skill, and ability desired by the shipyard. Long-term project. Per-diem is available for those that qualify. Call for full details: Edna (281) 965-2749. Office (956) 621-5398. Please send your resume to recruiter@laboronetx.com.

**Requisition ID: 177750** Plan, lay-out, weld, install, and repair all types of structural steel products in accordance with applicable plans, specifications, welding codes and industry standards. **Experience Level** Intermediate - Perform welding on various materials at required position using different welding processes, including, but not limited to, GTAW, SMAW, FCAW, GMAW and SAW. - Lay out, position, fit and weld various structural components, including flanges, piping supports, structural plates, beams, etc., in accordance with the supplied piping/structural fabrication drawings. - Set up, troubleshoot, and operate welding machines according to job specifications and welding procedures. - Adjust valves, gauges, and flames as needed and be capable of handling compressed gas and oxygen cylinders safely. - Operate air arc gouger, grinder, and other industry machines, tools, and equipment. **Qualifications** -May require a high school diploma or its equivalent with previous years of experience in the field or in a related area. -Must possess working knowledge skills and abilities for position. -Ability to understand, follow and transmit written and oral instructions and communicate effectively with management/supervision. -Ability to use hand tools, power tools and layout tools safe and efficiently. **Requirements** -Able to meet all physical requirements. -Must have all required tools -Expected to climb and work at heights and in confined spaces (may exceed 200 ft) -Able to work outdoors in all weather conditions -Able to work overtime, nights, and weekends as required by the workload -Observe and comply with all safety and project rules. Performs other duties as required. Equal Opportunity Employer, including disability and protected veteran status. Company: Kiewit_Craft

Offshore Fitter Job Description ** Offshore Fitter **Department:** Offshore **Employment Type:** Full-time The Offshore Fitter is responsible for accurately laying out, cutting, and fitting piping, vessel, and structural components based on supplied drawings or field-verified dimensions. This position requires offshore construction experience, physical capability, and a strong commitment to quality, productivity, and safety. The Fitter must maintain professionalism, show up on time, and work effectively with helpers, riggers, and welders. Key Responsibilities Figure material take-offs on drawings for required cut lengths. **Use pipe cutting machine, or if unavailable, use beveling machine to cut pipe to required length. Communicate with helper/rigger to identify needed material or equipment for each task. **Align parts using jacks, turnbuckles, wedges, drift pins, pry bars, and heavy hammers. Mark reference points on floor or face block and transpose them to workpiece using measuring devices, squares, chalk, and soapstone. Give instructions to welders to build up low spots or short pieces with weld. **Straighten warped or bent parts using sledge, hand torch, straightening press, and push-pull methods. **Remove high spots and cut bevels using hand files, portable grinders, and cutting torch. Examine blueprints and plan work sequence, applying knowledge of geometry, weld shrinkage, machining, and metal thickness. **Assemble and secure pipes, tubes, fittings, and related equipment using welding, brazing, cementing, soldering, and threading joints. Label all information on pipe before cutting; transfer item numbers onto cut sheet and carry them over to drop pipe. Inspect and test installed systems and pipelines using pressure gauges, hydrostatic testing, observation, or other methods. **Ascend/descend stairwells frequently with or without tools and equipment. Plan pipe system layout, installation, or repair per specifications. Read and understand blueprints and ISOs. **Demolish and install handrails and grating on platform. Verify all measurements, checking for square and level before releasing to welder. Note pre-weld dimensions on fitter drawings. **Hang and swing on vertical rope to/from platform and boat (potential rough seas/wind). Ensure all fabricated items are tagged with the correct job number, customer name, and piece number. **Climb and work from heights. **Pull tools and equipment up/down to workstations or areas. Show up to work on time and as scheduled. Inspect all equipment daily (torch, torch hoses, grinder, levels, tapes, etc.). Maintain a clean and safe work area by sweeping as needed. Complete and discuss a thorough Job Safety and Environmental Analysis (JSEA) prior to each task. Maintain a positive attitude toward customers and represent ACI professionally. What You Need to Know Preferably 2 years minimum experience in fitting (piping, vessel, and structural) fabrication. Minimum of 2 years recent offshore construction experience. Most recent offshore experience within the last 4 years. Ability to read and interpret ISOs and blueprints. Familiarity with offshore emergency response, escape procedures, and water survival skills. HSE Responsibilities Embrace, lead, and demonstrate “Acadian F.I.R.S.T.” - Vision & Mission Statement as fundamental core values. Demonstrate visible leadership and support proactive safety processes (JSA, Time Out & TEAM BBS Observations) to achieve an incident-free workplace and advance our safety culture. Adhere to all Health, Safety & Environmental (HSE) Management System policies, procedures, safe work practices, and client-specific regulatory requirements. Make a personal commitment and be accountable for HSE results, driving toward the achievement of defined goals. Clearly communicate these goals through direct reports, while coaching, mentoring, and empowering others to achieve desired outcomes. Conduct periodic quality assessments of HSE processes to enhance personal coaching and mentoring effectiveness and demonstrate ownership in the successful implementation of HSE programs.

About Us We have earned a reputation for leading the industry in turnarounds, specialty welding, construction, pipe fabrication, and maintenance. Backed by a team of talented supervisors and craft professionals, we are prepared to tackle the toughest jobs for clients in the refining, chemical, petrochemical, renewables, and midstream industries. Job Summary Combination Welders must have industrial welding experience in a petrochemical or related industrial fabrication facility. Welders having the ability to read and interpret blueprints, ISO's, field drawings, and material takeoffs a plus. Welders will perform a range of duties which will include but is not limited to welding various metals using processes such as SMAW, GMAW, FCAW, and GTAW. Welders are responsible for selecting, setting up, and staging the proper equipment for their jobs and that each are in ample supply and working order. This includes welding machines, gases, tools, and other consumables. Welders are also responsible for double checking the fit of pipe or other structural pieces and to allow for proper attachment. Attention to safety and detail are of the utmost importance. Welders must successfully pass pre-employment weld tests as part of the on-boarding process. Requirements Industrial Combo welding experience with GTAW and SMAW. Must pass GTAW & SMAW manual welding procedures test. Current Basic Orientation Plus (Safety Council Card) or within 3 months expiration. Current TWIC card Have three (3) or more years' experience in your craft. Compliance with designated welding procedures and specifications. Follow established job-site safety and work regulations, as well as maintaining a safe and clean work area. Identify safety hazards you or other employees may be subject to and take all necessary corrective action to eliminate or minimize hazards. Use appropriate hand and power tools to properly measure, cut, assemble, weld and install all types of pipe and/or similar tubular products; install supports, valves and other control equipment; test installed piping systems and install all other related items in accordance with the applicable plans and specifications; bolt, clamp or weld parts to secure in position for welding; weld components according to specific process and code. Produce quality work, meeting requirements of plans, specifications and industry standards. Physical Requirements Significant and sustained periods of standing, walking, bending, squatting and lifting. Good communication skills (speaking and actively listening) with co-workers and supervisors. Must have good manual dexterity to perform precision adjustments of machinery parts and controls. Will use arms and hands to signal, grab, hold, turn, push, and pull: objects, materials, controls and tools. May be required to lift, carry and move up to 50lbs. Will work at heights, climb ladders and stairways and work off of platforms. Will work at heights up to 300' utilizing proper fall protection. Will use vision abilities to focus, see short and long distances, colors, depth perception and peripheral vision. Must be capable of working outside in the elements including but not limited to the heat, cold, rain, snow and wind; and must be able to work for long period of times up to 12 hours a day. Will be required to wear personal protective equipment (PPE) including but not limited to: hard hat, safety glasses/goggles, ear plugs/muffs, masks/respirators, safety vests, gloves and steel-toe boots. We offer our employees a competitive salary and comprehensive benefits package and are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled Notice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here. Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent. #REPCON Equal Opportunity Employer As a leading provider of mechanical and electrical construction, facilities services, and energy infrastructure, we offer employees a competitive salary and benefits package and we are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/Disabled Notice to Prospective Employees Notice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here. Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process - it is probably fraudulent.

Job Description Industrial Air Flow Dynamics, Inc. is now hiring for our Spring Season! (March - June) We've Got the Gear, the Travel, and the Pay - Just Bring the Skill At Industrial Air Flow Dynamics, Inc., we know great welders don't just need a paycheck, they need support. That's why we supply all the tools and PPE required for each job, cover your travel and hotel, pay you for passing your weld test, and even reward you for bringing your friends along. When you work with us, you're not just another name on a roster. You're part of the crew that keeps America's power plants running. We're hiring experienced Stainless Steel Structural Welders (Flux-Core Process) for long term, nationwide turnaround work. If you're dependable, driven, and ready to get paid to travel, read on. Why Weld with Us? Tools & PPE Provided - No need to haul your gear. We've got it covered. Travel Covered - We pay your airfare and provide shared hotel accommodations. Daily Per Diem - $30/day to cover meals and incidentals. Referral Bonuses - Know someone who's got what it takes? Get paid when we hire them. Fair Pay - $25/hour + $15/hour paid while you travel time to the project The Job You'll travel across the U.S. to power plant sites, welding stainless steel structural components using the Flux-Core process (309 wire on ½" carbon plate). You'll read and work from detailed blueprints, and perform 2G, 3G, and 4G welds in all positions including overhead and vertical, in high-pressure, physically demanding environments like boilers and scaffolding systems. What We're Looking For 3+ years of industrial welding experience Ability to pass bend-tested welds: 2G, 3G, and 4G (Flux-Core, 309 wire) Comfortable working at heights and in tight, hot spaces Willing to travel continuously nationwide Strong work ethic, blueprint reading skills, and commitment to safety Pay & Benefits $25/hour base pay + $15/hour travel pay + $30/day per diem Paid airfare + hotel accommodations Rental car provided (must have valid driver's license) Referral bonuses when your referrals get hired Full Benefits Package Includes: Safe Harbor 401(k) Medical, Dental & Vision coverage Life, AD&D, Short & Long-Term Disability options Quick, No-Nonsense Hiring Process Our application is simple and fast. No long forms, no fluff. Just tell us who you are, where you've worked, and how to reach you. If it's a match, we'll reach out from an 281 area code. Next Steps: Phone screening Weld test (with clear instructions) Drug Test If you're a skilled welder who wants to travel the country, earn great pay, and work with a team that has your back, this is your chance. Apply now and bring your skills to the job. We'll handle the rest! Job Posted by ApplicantPro

Job Description No teaching experience required, we will provide all necessary tools and training to succeed!! We call it being a life changer, but you'll call it a job you love while helping others find the same. You'll have a hand in improving the lives of countless SCI students throughout Texas by working with impassioned educators and campus faculty in a collaborative, interactive environment to create optimized environment for our students. Responsibilities Demonstrates and applies a thorough and accurate knowledge of the teaching field and discipline; Plans and organizes instruction in ways which maximize student learning. Practice excellence in teaching and instruction; Modifies instructional methods and strategies to meet diverse students' needs; Prepare lesson plans and teach course as prescribed by the approved institutional curriculum; Encourages the development of communication skills and higher order thinking skills through appropriate assignments. Requirements Minimum of 3 years of industry experience preferred; Prior post-secondary related teaching experience of at least 1 year in subject matter is highly preferred; Certified AWS and/or NCCER. Benefits Training & Development Fun & Energetic, Family-Based Environment Continuous Growth Opportunities Medical, Dental, & Vision Options Health Savings & Flexible Spending Options (HSA & FSA) Basic Life & Accident Insurance Short & Long-term Disability 401K Retirement Plan SCI is an Equal Opportunity employer. About Southern Careers Institute SCI has been changing lives for over 60 years, now and we're just getting started. We offer certification-based training with programs in Medical, Business, Cosmetology, Skilled-Trades and Technology with campuses spanning across central and south Texas as well as online. Our students can graduate most of our programs in under one year and with real-world experience under their belt.

No teaching experience required, we will provide all necessary tools and training to succeed!! Full and part-time available We call it being a life changer, but you'll call it a job you love while helping others find the same. You'll have a hand in improving the lives of countless SCI students throughout Texas by working with impassioned educators and campus faculty in a collaborative, interactive environment to create optimized environment for our students. Responsibilities * Demonstrates and applies a thorough and accurate knowledge of the teaching field and discipline; * Plans and organizes instruction in ways which maximize student learning. Practice excellence in teaching and instruction; * Modifies instructional methods and strategies to meet diverse students' needs; * Prepare lesson plans and teach course as prescribed by the approved institutional curriculum; * Encourages the development of communication skills and higher order thinking skills through appropriate assignments. Requirements * Minimum of 3 years of industry experience preferred; * Prior post-secondary related teaching experience of at least 1 year in subject matter is highly preferred; * Certified AWS and/or NCCER. Benefits * Training & Development * Fun & Energetic, Family-Based Environment * Continuous Growth Opportunities * Medical, Dental, & Vision Options * Health Savings & Flexible Spending Options (HSA & FSA) * Basic Life & Accident Insurance * Short & Long-term Disability * 401K Retirement Plan * SCI is an Equal Opportunity employer. About Southern Careers Institute SCI has been changing lives for over 60 years, now and we're just getting started. We offer certification-based training with programs in Medical, Business, Cosmetology, Skilled-Trades and Technology with campuses spanning across central and south Texas as well as online. Our students can graduate most of our programs in under one year and with real-world experience under their belt.

←Back to all jobs at FORCE PRESSURE CONTROL LLC Sub Arc Welder FORCE PRESSURE CONTROL LLC is an EEO Employer - M/F/Disability/Protected Veteran Status OFS Facility Operations | Sub Arc Welder Force Pressure Control is seeking safety-oriented production personnel to work in its Orange Grove facility. Welding personnel must be able to operate with and without supervision, prepare and initiate jobs, maintain machinery and working production area, and record all data outlined in QAQC protocols. Three years working experience within sub arc work scopes is required as is working experience with alloys and API ring grooves. Working background with valve and other wellhead / surface pressure control equipment is valued. Candidates must be able to successfully pass bend test The Sub Arc Welder position is a full time, non-exempt position. Overtime in excess of 40 hours per work week will be required. Hourly pay rate commensurate with experience. Applicants have rights under Federal Employment Laws. Please visit our careers page to see more job opportunities.