Welder jobs in Palm Springs, CA - 474 jobs

Full-time Description The general purpose of this position is to weld simple to complex components and/or structures while meeting all safety, quality, and schedule requirements. Responsible for various types of weld preparation, welding, and weld finishing operations to accomplish welding in accordance with customer drawings and specifications. Requirements Proficient in assigned aluminum welding techniques, including weld fillets, gusset toe and wraps, frame wraps and termination Demonstrated ability to weld into corners / vertical intersections with minimal blending Ability to evaluate and correct basic weld pick up, with minimal supervision Basic knowledge in assigned welding techniques Basic knowledge of wire and filler material applications for various steel alloys and aluminum Working knowledge of fixturing and weld set up parameters (amps, volts, etc.) Working in compliance with all safety, quality, environmental and health requirements. Job Requirements Must be able to pass eye test and workmanship qualification test. Must be tested and fit for respirator use. Willing to work any shift and overtime as required. Education and/or Experience High school diploma required. Minimum of 2 years of proven experience in a welding trade is required. Shipyard experience is preferred, but not required. Knowledge, Skills, and Abilities Ability to take direction and follow instructions Good mechanical aptitude with ability to produce consistent quality Ability to inspect and correct basic weld pick-up without supervision Ability to work independently and as part of a team Problem-solving and trouble-shooting skills Excellent hand-eye coordination; good spatial orientation Ability to consistently meet production deadlines Ability to use conventional and precision measuring instruments Ability to pass a skills evaluation test to demonstrate welding ability Ability to weld in uncomfortable positions where applicable Ability to work on beams, scaffolding, ladders and confined spaces. Ability and willingness to work with and to teach less-skilled workers Ability to maintain and perform routine preventive maintenance on welding equipment Physical Requirements: Frequent standing, balancing, walking, climbing ladders or equipment, reaching above shoulder or out in front, manual dexterity, pushing, pulling, kneeling, bending, seeing, hearing and occasionally lowering self into confined spaces, crawling through small openings and working in reclined positions, as needed. Physical ability to lift, push, pull and carry 50+ lbs., bend, stoop and climb scaffold and work on elevated work surfaces, beams, ladders, and confined spaces. While performing the duties of this job the employee is regularly required to use hands and fingers to handle, feel, talk, or hear. The vision requirements include close vision, distance vision, peripheral vision, depth perception and ability to adjust focus. Works in all areas of the shipyard and on-board ships. Hearing warning signals and reading and comprehending safety instructions. Must be able to maintain general safety awareness and avoid hazards commonly present in employee's work area. The noise level in the work environment can vary and is often loud. Salary Description $25 - $38 Hourly - DOE

Your Work Shapes the World at Caterpillar Inc. When you join Caterpillar, you're joining a global team who cares not just about the work we do - but also about each other. We are the makers, problem solvers, and future world builders who are creating stronger, more sustainable communities. We don't just talk about progress and innovation here - we make it happen, with our customers, where we work and live. Together, we are building a better world, so we can all enjoy living in it. About the Role: This position is for experienced welders who are able to use the necessary equipment for MIG and TIG welding of structures, enclosures, pipes, and other components, as well as general fabrication and refurbishment, and operating equipment and heavy machinery. Experienced welders who are able to perform open root welding. What You Will Do: * Plan sequences of welding operations and determine methods of welding to weld structural details and assemblies, using all available welding processes such as gas, electric arc, (GTAW), heli-arc, orbital, sigma and submerged arc welding. Perform setup incidental for welding operations, working from blueprints, sketches, other authorized documents and/or oral instructions. Weld any gauge materials where welded areas are subject to high pressure or extreme stress and where care must be taken to prevent leaks and cracks. * Weld flat, vertical or overhead areas, or in difficult positions and areas difficult of access. Recognize need for and pre-heat materials as necessary and minimize warpage by proper location of weld and stress relieving methods. Form and shape details, as required. Improvise welding aids such as paper templates, locating devices, holding blocks, etc. * Perform surface preparation of parts such as cleaning, sanding, grinding, polishing and some assembly of parts. Clean and dress welds including the cutting and repairing of unacceptable weld joints. * Check own work for conformance to specifications. Must pass and maintain required certifications. Use all necessary equipment, tools and materials required to perform work as a journeyman. Must be able to climb and weld from ladders, scaffolds roofs, and in pits. Maintain good shop practices. What You Have: * Must be able to pass multiple welder qualification tests * Minimum of three (3) years GTAW 2G and 3G experience in a production environment * Available to work any shift * Ability to perform simple computer operations, work from digital prints Desired Qualifications: * Three (3) to five (5) years of GTAW welding experience * Experience welding with precision fixturing * Ability to work overtime as needed Summary Pay Range: $32.52- $48.78 Compensation and benefits may vary depending on multiple individualized factors, job level, market, location, job-related knowledge, skills, individual performance, and experience. Please note that salary is only one component of total compensation at Caterpillar. Benefits: Subject to plan eligibility, terms, and guidelines. This is a summary list of benefits. * Medical, dental, and vision benefits* * Paid time off plan (Vacation, Holidays, Volunteer, etc.)* * 401(k) savings plans* * Health Savings Account (HSA)* * Flexible Spending Accounts (FSAs)* * Health Lifestyle Programs* * Employee Assistance Program* * Voluntary Benefits and Employee Discounts* * Career Development* * Incentive bonus* * Disability benefits * Life Insurance * Parental leave * Adoption benefits * Tuition Reimbursement * Sign on bonus * These benefits also apply to part-time employees This employer is not currently hiring foreign national applicants that require or will require sponsorship tied to a specific employer, such as H, L, TN, F, J, E, O. Posting Dates: Any offer of employment is conditioned upon the successful completion of a drug screen. Caterpillar is an Equal Opportunity Employer, Including Veterans and Individuals with Disabilities. Qualified applicants of any age are encouraged to apply. Not ready to apply? Join our Talent Community.

Job Description Company Background: We are 24 (and growing) market-leading operating companies that deliver unmatched HVAC, mechanical, refrigeration, plumbing, and electrical solutions. We are actively building the nation's preferred technical service partnership for commercial MEP+ ecosystems, empowering industrial, commercial, and institutional clients-including Fortune 500 companies and other industry leaders across the United States-with reliable, innovative service. Learn more about us at ************************ WHO WE ARE Retrofit Technology is part of the Kelso Industries family of companies, a rapidly growing group of mechanical, electrical, and plumbing (MEP+) contractors committed to excellence in safety, quality, customer success, and craftsmanship. Based in Bloomington, California, Retrofit Technology specializes in all aspects of commercial HVAC systems, including installation, maintenance, and service. Our team is equipped to handle projects from start to finish with precision and care. Backed by certified welders, electricians, and service technicians, we have the expertise to tackle even the most challenging HVAC retrofit and mechanical projects-delivering exceptional results every time. ABOUT THE ROLE We are seeking an experienced Pipe Welder to join our growing team and support mechanical and HVAC retrofit projects across Southern California. This position is based out of Bloomington, CA and requires frequent travel to job sites throughout the region. A daily per diem is provided and hotel accommodations are covered by the company when overnight stays are necessary. The Pipe Welder will be responsible for fabricating, assembling, and installing piping systems for commercial and industrial HVAC applications. The ideal candidate has hands-on experience with multiple welding methods and piping materials, values safety and quality, and can work both independently and as part of a field crew. RESPONSIBILITIES Weld and assemble piping systems using various methods (TIG, MIG, stick, brazing, soldering, etc.). Fit, align, and secure pipe systems and supports according to specifications and drawings. Read and interpret blueprints, schematics, and technical drawings. Fabricate and install copper, carbon steel, stainless steel, and PVC piping. Perform rigging, demo, and installation work on HVAC retrofit projects. Inspect completed welds to ensure compliance with codes and safety standards. Collaborate with project managers, foremen, and other trades to complete projects efficiently. Maintain a clean, safe, and organized work area in compliance with OSHA and company policies. QUALIFICATIONS High school diploma or GED equivalent. 3+ years of experience in pipe welding or mechanical retrofit environments. Proficiency in one or more of the following: Soldering or brazing copper pipe Welding carbon or stainless steel pipe Fitting or threading steel and PVC pipe Ability to pass a pipe welding test (administered at our Bloomington shop). Skilled at reading and following mechanical drawings and specifications. Valid driver's license and willingness to travel throughout Southern California. Strong attention to detail, reliability, and safety mindset. COMPENSATION & BENEFITS Hourly wage: $30 - $50 per hour (based on experience and certification) Per diem and hotel accommodations provided for overnight travel Paid travel time to and from job sites Comprehensive benefits package: Medical and dental (50% employer paid) 401(k) with up to 4% company match Eligibility after 30 days of employment Paid Time Off (PTO) and company holidays Opportunities for long-term growth within the Kelso Industries family JOIN OUR TEAM If you're a skilled welder who takes pride in craftsmanship and enjoys working on complex HVAC retrofit projects, we'd love to hear from you. Apply today to join a team that values safety, integrity, and excellence in every project. Our compensation reflects the cost of labor across several US geographic markets. The base pay for this position ranges from our lowest geographic market up to our highest geographic market. Pay is based on a number of factors including market location and may vary depending on job-related knowledge, skills, and experience. Amazon is a total compensation company. Dependent on the position offered and forms of compensation that may be provided as part of a total compensation package, in addition to a full range of medical, financial, and/or other benefits. California Pay Range$30-$40 USD Why Join Us? We're committed to attracting talented individuals who seek a company with a strong foundation of success and an outstanding culture. We proactively provide competitive compensation, comprehensive benefits, and clear pathways for career advancement with autonomy and flexibility in an entrepreneurial environment. Learn more about us at ************************ We celebrate diversity and are committed to creating an inclusive environment for all employees. We do not discriminate in any aspect of employment on the basis of race, color, religion, national origin, ancestry, gender, sexual orientation, gender identity and/or expression, age, veteran status, disability, or any other characteristic protected by federal, state, or local employment discrimination laws where Kelso does business.

Your Work Shapes the World at Caterpillar Inc. When you join Caterpillar, you're joining a global team who cares not just about the work we do - but also about each other. We are the makers, problem solvers, and future world builders who are creating stronger, more sustainable communities. We don't just talk about progress and innovation here - we make it happen, with our customers, where we work and live. Together, we are building a better world, so we can all enjoy living in it. About the Role: This position is for experienced welders who are able to use the necessary equipment for MIG and TIG welding of structures, enclosures, pipes, and other components, as well as general fabrication and refurbishment, and operating equipment and heavy machinery. Experienced welders who are able to perform open root welding. What You Will Do: Plan sequences of welding operations and determine methods of welding to weld structural details and assemblies, using all available welding processes such as gas, electric arc, (GTAW), heli-arc, orbital, sigma and submerged arc welding. Perform setup incidental for welding operations, working from blueprints, sketches, other authorized documents and/or oral instructions. Weld any gauge materials where welded areas are subject to high pressure or extreme stress and where care must be taken to prevent leaks and cracks. Weld flat, vertical or overhead areas, or in difficult positions and areas difficult of access. Recognize need for and pre-heat materials as necessary and minimize warpage by proper location of weld and stress relieving methods. Form and shape details, as required. Improvise welding aids such as paper templates, locating devices, holding blocks, etc. Perform surface preparation of parts such as cleaning, sanding, grinding, polishing and some assembly of parts. Clean and dress welds including the cutting and repairing of unacceptable weld joints. Check own work for conformance to specifications. Must pass and maintain required certifications. Use all necessary equipment, tools and materials required to perform work as a journeyman. Must be able to climb and weld from ladders, scaffolds roofs, and in pits. Maintain good shop practices. What You Have: Must be able to pass multiple welder qualification tests Minimum of three (3) years GTAW 2G and 3G experience in a production environment Available to work any shift Ability to perform simple computer operations, work from digital prints Desired Qualifications: Three (3) to five (5) years of GTAW welding experience Experience welding with precision fixturing Ability to work overtime as needed Summary Pay Range: $32.52- $48.78 Compensation and benefits may vary depending on multiple individualized factors, job level, market, location, job-related knowledge, skills, individual performance, and experience. Please note that salary is only one component of total compensation at Caterpillar. Benefits: Subject to plan eligibility, terms, and guidelines. This is a summary list of benefits. Medical, dental, and vision benefits* Paid time off plan (Vacation, Holidays, Volunteer, etc.)* 401(k) savings plans* Health Savings Account (HSA)* Flexible Spending Accounts (FSAs)* Health Lifestyle Programs* Employee Assistance Program* Voluntary Benefits and Employee Discounts* Career Development* Incentive bonus* Disability benefits Life Insurance Parental leave Adoption benefits Tuition Reimbursement Sign on bonus * These benefits also apply to part-time employees This employer is not currently hiring foreign national applicants that require or will require sponsorship tied to a specific employer, such as H, L, TN, F, J, E, O. Posting Dates: Any offer of employment is conditioned upon the successful completion of a drug screen. Caterpillar is an Equal Opportunity Employer, Including Veterans and Individuals with Disabilities. Qualified applicants of any age are encouraged to apply. Not ready to apply? Join our Talent Community.

Craft and Technical Solutions is an established Marine and Industrial Staffing Company with offices nationwide. We partner with businesses and jobseekers to place qualified individuals efficiently. Currently, CTS is reviewing resumes for Pipe Welders in Sturgeon Bay, WI! Pay Rate: $40/hour and $660/week per diem Job Description: Read blueprints and other customer specifications/drawings. Carbon 309 Stainless Steel Wired 20 Copper Nickel (TIG). 6GR Requirements Minimum 8 years of naval/commercial welding experience. Must have reliable transportation. Familiar with OSHA regulations relative to the shipbuilding industry. Pass hair follicle test and background check. Comfortable with heights and in confined spaces. Lift 50lbs without assistance. Must understand the layout of the ship and compartment identification. Basic reading, writing and math skills required. Must be a US citizen. Benefits CTS, LLC offers a comprehensive benefit package to eligible employees. Eligible employees may enroll in: Health Dental Vision Voluntary Life/Voluntary AD&D Short-Term Disability Long-Term Disability Hospital Indemnity Accident Critical Illness 401k Safety and responsible work practices are of paramount importance at CTS and are woven into the fabric of everything we do. We are committed to employee safety & development, the protection of the environment and the communities where we operate. We are ready to be a partner in your career success! Reasonable Accommodations may be made to enable qualified individuals with disabilities to perform essential job functions. Craft and Technical Solutions, LLC has a consistent policy that requires an online application to be completed before we can further consider you as an applicant for this position. CTS is an EOE AA M/F/Vet/Disability

We are looking for a WELDER to join our Colton plant. As a welder with Rinker Materials, you will contribute to one of the nation's largest manufacturers of reinforced concrete pipe, box, bridge, and other related infrastructure products for stormwater and sanitary applications. You will work and become part of a community that prioritizes not only our customers but also values our dedicated and loyal employees. Why apply? Competitive pay Medical and prescription drug coverage Dental and vision coverage Health savings and flexible spending account 401(k) with company match Life insurance and disability coverage Paid vacation Paid holidays Growth & Development opportunities Employee Discounts Mental Health through our Employee Assistance Program Wellness benefits including low-cost gym memberships About the Role: Responsibilities: Welding and Fabrication: Operate welding equipment to assemble and weld cages, ensuring they meet required specifications and quality standards. Reading Blueprints: Interpret and work from engineering drawings and blueprints to accurately assemble cages according to design specifications. Material Handling: Select and prepare materials for welding, including cutting, fitting, and positioning components Welding Techniques: Utilize various welding techniques, such as MIG, TIG, or stick welding, to join metal components securely. Quality Control: Inspect finished products to ensure they meet quality and safety standards, making any necessary adjustments or repairs. Safety Compliance: Adhere to all safety protocols and guidelines to prevent workplace accidents and injuries Equipment Maintenance: Maintain and perform routine checks on welding equipment to ensure it functions properly. Collaboration: Work in coordination with other team members to achieve production goals and timelines. Record Keeping: Maintain records of completed work and any necessary documentation for quality control and production tracking. Continuous Improvement: Suggest and implement process improvements to enhance productivity and product quality. Any other miscellaneous tasks assigned by management at any given time and in any given area About You We Require: Great work ethic and impeccable attendance. Able to read and understand work orders and complex instructions. Familiarity with hand tools and power tools. Ability to work outdoors or in open air environment. Preferred - Experience working in a manufacturing environment. Preferred - Experience operating a forklift, especially an industrial forklift. Must be able to lift and move objects up to 50 pounds frequently. Over 50 pounds, a forklift or crane will be used. Must be able to push or pull cart with 80 pounds of force. Must be able to climb stairs and ladders. Must be able to step up 20 inches. About Us: As you explore the career opportunities at Rinker, you'll discover a wide range of positions. We're always on the lookout for passionate individuals who are committed to Excellence and share our vision of a better future. If you're ready to take the next step in your career and contribute to some of the most exciting infrastructure projects, we invite you to explore our current job openings and start your journey with us. Let's build a better future together. Ready to Apply? · The process is simple. Click on the “apply” button to get started. We are looking for a WELDER to join our Colton plant. As a welder with Rinker Materials, you will contribute to one of the nation's largest manufacturers of reinforced concrete pipe, box, bridge, and other related infrastructure products for stormwater and sanitary applications. You will work and become part of a community that prioritizes not only our customers but also values our dedicated and loyal employees. Why apply? Competitive pay Medical and prescription drug coverage Dental and vision coverage Health savings and flexible spending account 401(k) with company match Life insurance and disability coverage Paid vacation Paid holidays Growth & Development opportunities Employee Discounts Mental Health through our Employee Assistance Program Wellness benefits including low-cost gym memberships About the Role: Responsibilities: Welding and Fabrication: Operate welding equipment to assemble and weld cages, ensuring they meet required specifications and quality standards. Reading Blueprints: Interpret and work from engineering drawings and blueprints to accurately assemble cages according to design specifications. Material Handling: Select and prepare materials for welding, including cutting, fitting, and positioning components Welding Techniques: Utilize various welding techniques, such as MIG, TIG, or stick welding, to join metal components securely. Quality Control: Inspect finished products to ensure they meet quality and safety standards, making any necessary adjustments or repairs. Safety Compliance: Adhere to all safety protocols and guidelines to prevent workplace accidents and injuries Equipment Maintenance: Maintain and perform routine checks on welding equipment to ensure it functions properly. Collaboration: Work in coordination with other team members to achieve production goals and timelines. Record Keeping: Maintain records of completed work and any necessary documentation for quality control and production tracking. Continuous Improvement: Suggest and implement process improvements to enhance productivity and product quality. Any other miscellaneous tasks assigned by management at any given time and in any given area About You We Require: Great work ethic and impeccable attendance. Able to read and understand work orders and complex instructions. Familiarity with hand tools and power tools. Ability to work outdoors or in open air environment. Preferred - Experience working in a manufacturing environment. Preferred - Experience operating a forklift, especially an industrial forklift. Must be able to lift and move objects up to 50 pounds frequently. Over 50 pounds, a forklift or crane will be used. Must be able to push or pull cart with 80 pounds of force. Must be able to climb stairs and ladders. Must be able to step up 20 inches. About Us: As you explore the career opportunities at Rinker, you'll discover a wide range of positions. We're always on the lookout for passionate individuals who are committed to Excellence and share our vision of a better future. If you're ready to take the next step in your career and contribute to some of the most exciting infrastructure projects, we invite you to explore our current job openings and start your journey with us. Let's build a better future together. Ready to Apply? · The process is simple. Click on the “apply” button to get started.

We are looking for a WELDER to join our Colton plant. As a welder with Rinker Materials, you will contribute to one of the nation's largest manufacturers of reinforced concrete pipe, box, bridge, and other related infrastructure products for stormwater and sanitary applications. You will work and become part of a community that prioritizes not only our customers but also values our dedicated and loyal employees. Why apply? * Competitive pay * Medical and prescription drug coverage * Dental and vision coverage * Health savings and flexible spending account * 401(k) with company match * Life insurance and disability coverage * Paid vacation * Paid holidays * Growth & Development opportunities * Employee Discounts * Mental Health through our Employee Assistance Program * Wellness benefits including low-cost gym memberships About the Role: Responsibilities: * Welding and Fabrication: Operate welding equipment to assemble and weld cages, ensuring they meet required specifications and quality standards. * Reading Blueprints: Interpret and work from engineering drawings and blueprints to accurately assemble cages according to design specifications. * Material Handling: Select and prepare materials for welding, including cutting, fitting, and positioning components * Welding Techniques: Utilize various welding techniques, such as MIG, TIG, or stick welding, to join metal components securely. * Quality Control: Inspect finished products to ensure they meet quality and safety standards, making any necessary adjustments or repairs. * Safety Compliance: Adhere to all safety protocols and guidelines to prevent workplace accidents and injuries * Equipment Maintenance: Maintain and perform routine checks on welding equipment to ensure it functions properly. * Collaboration: Work in coordination with other team members to achieve production goals and timelines. * Record Keeping: Maintain records of completed work and any necessary documentation for quality control and production tracking. * Continuous Improvement: Suggest and implement process improvements to enhance productivity and product quality. * Any other miscellaneous tasks assigned by management at any given time and in any given area About You We Require: * Great work ethic and impeccable attendance. * Able to read and understand work orders and complex instructions. * Familiarity with hand tools and power tools. * Ability to work outdoors or in open air environment. * Preferred - Experience working in a manufacturing environment. * Preferred - Experience operating a forklift, especially an industrial forklift. * Must be able to lift and move objects up to 50 pounds frequently. Over 50 pounds, a forklift or crane will be used. Must be able to push or pull cart with 80 pounds of force. Must be able to climb stairs and ladders. Must be able to step up 20 inches. About Us: As you explore the career opportunities at Rinker, you'll discover a wide range of positions. We're always on the lookout for passionate individuals who are committed to Excellence and share our vision of a better future. If you're ready to take the next step in your career and contribute to some of the most exciting infrastructure projects, we invite you to explore our current job openings and start your journey with us. Let's build a better future together. Ready to Apply? * The process is simple. Click on the "apply" button to get started.

We have immediate openings for ALUMINUM WELDERS. You must be able to set up welding machines and equipment (both MIG and TIG); read and interpret blueprints to understand the product's specifications; weld, cut, grind and finish the product; and inspect your work for accuracy and quality and the ability to certify to our processes. Required Skills: Must be able to qualify in the following welding process: Aluminum TIG and MIG weld Multi-pass. All position fillet and butt welds using the following processes: SMAW (Shielded Metal Arc Welding), GMAW (Gas Metal Arc Welding), and FCAW (Flux Cored Arc Welding). Aluminum 5XXX Air Carbon Arc Gouging. Ability to properly use fillet and butt weld gauges. Experience working in a physically demanding environment (shipboard, sub-assemblies, ladders, staging, etc.). Familiarity with OSHA regulations relative to the shipbuilding industry. Welding Qualifications: All Welders are required to pass all position, Multi-pass Butt Weld, Welder Qualification Tests prior to reporting for the first day of productive work. These tests will be in accordance with MIL-STD-248D Paragraph 5.3.3. Job Requirements: Minimum 5 years Aluminum welding experience Aluminum 5XXX experience required Must pass drug and background screening DBIDS eligible Labor One Staffing is an Equal Opportunity Employer Shipyard experience is required. Please contact our team for more information! Cell: (619)657-5507 or (858)717-1672 Walk-ins Accepted! 1625 Hoover Avenue National City, CA 91950 Office Hours: 8:00 AM-5:00 PM

Job Description Leading large-scale commercial plumbing contractor is seeking an experienced pipe welder to join their team. This person will be responsible for various types of weld preparation, welding, and weld finishing operations to manufacture product to drawings, specifications, or other forms of instruction. Ideal candidate must be adaptable and able to work in a fast-paced environment. Qualifications: Must have experience with Stainless Steel and Carbon Pipe. Posses working knowledge of Mig and Stick welding techniques Relevant certs required Minimum of 2 years of experience with industrial pipe welding Familiarity with torch operation and ability to use skillfully Iron Mechanical offers a competitive salary, medical, dental, vision, 401K benefits, paid time off and sick leave, and travel/per diem pay for jobsite travel.

Requirements To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Education and/or Experience High school diploma or general education degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience. Language Skills Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals. Ability to write routine reports and correspondence. Ability to speak effectively before groups of customers or employees of organization. Mathematical Skills Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graphs. Reasoning Ability Ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form. Ability to deal with problems involving several concrete variables in standardized situations. Computer Skills Basic Computer Skills including use of email may be required. Certificates, Licenses, Registrations N/A Physical Demands The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this Job, the employee is regularly required to stand. The employee is frequently required to use hands to finger, handle, or feel and reach with hands and arms. The employee is occasionally required to walk; sit; climb or balance; stoop, kneel, crouch, or crawl; talk or hear and taste or smell. The employee must occasionally lift and/or move up to 50 pounds. Salary Description 23-25/hour

Job DescriptionBenefits: 401(k) 401(k) matching Health insurance Opportunity for advancement Paid time off Pay & Schedule Pay: $23 $28/hr (DOE) Shift: 1st shift 6:00 AM to 2:30 PM Status: Full-Time Days: Monday Friday Availability: Must be willing to work overtime and weekends when required. About Us Paradigm Ironworks is a Riverside-based structural steel fabrication shop specializing in high-quality stairs, rails, gates, and architectural steel for commercial, industrial, and public works projects. We are known for precision craftsmanship, on-time delivery, and a strong safety culture. Key Responsibilities Maintain a safe and organized work environment in compliance with OSHA and company standards. Fit, weld, and fabricate structural steel stairs, rails, and related components to precise specifications. Work directly from detailed shop drawings and welding symbols. Perform accurate layout, cutting, and preparation of steel components prior to assembly. MIG weld using 71M steel wire for high-strength connections. Collaborate with other welders and shop staff to meet production deadlines without sacrificing quality. Ensure final products meet AWS quality standards and project specifications. Requirements Minimum 5 years experience as a welder/fitter in structural steel fabrication. AWS Certification required. Proven ability to read and interpret shop drawings and structural details. Strong experience with stairs, rails, and architectural steel fabrication. Proficient with MIG welding (71M wire). Able to lift up to 50 lbs and stand for extended periods. Strong work ethic, attention to detail, and pride in craftsmanship.

Nikkiso Clean Energy & Industrial Gases is a leading provider of cryogenic pumps, heat exchangers, process systems, services, and solutions for the LNG and industrial gases industry. We are a subsidiary of Nikkiso Company Ltd, a leading industrial manufacturer headquartered in Tokyo, Japan, with over $1.5 B in annual revenue, 8000 + employees worldwide, and publicly traded on the Tokyo Stock Exchange. Job Overview Nikkiso Cryoquip is a leading manufacturer of heat exchangers, liquefiers, and vaporizers for the LNG and industrial gases industry. Applications include fueling stations, marine engines, peak shaving, power generation, virtual pipelines, and well stimulation. Summary We are looking for a skilled TIG Welder to cut and join metals and other materials at our facility. You will operate appropriate equipment to put together mechanical structures or parts with a great deal of precision. Your job is important as it provides the foundation for strong infrastructure. A welder must be competent in using potentially dangerous equipment following all safety precautions. The ideal candidate will have a steady hand and great attention to detail. Knowledge of different kinds of metal and their properties is essential. A GTAW pipe test is required to interview for this role. Hourly Rate $20-$22 Equal Opportunity Employer/Veterans/Disabled Nikkiso CE&IG is proud to be an equal opportunity employer. We celebrate diversity and are committed to creating an inclusive environment for all employees. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, or protected veteran status and will not be discriminated against on the basis of disability. Responsibilities Essential Functions/Responsibilities Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. * Read blueprints and drawings and take or read measurements to plan layout and procedures * Determine the appropriate welding equipment or method based on requirements * Set up components for welding according to specifications * Operate angle grinders to prepare the parts that must be welded * Align components using rulers, tape measurers etc. and clamp pieces * Weld components using manual or semi-automatic welding equipment in various positions (vertical, horizontal, or overhead) * Able to determine that weld meets ASME SSC IX specifications * Maintain equipment in a condition that does not compromise safety Supervisory Responsibility This position has no direct supervisory responsibilities. Work Environment This job operates in a warehouse environment. This role routinely utilizes the operation of material handling equipment and various tools and machinery. Physical Demands While performing the duties of this job, the employee is regularly required to talk or hear. Specific vision abilities required by this job include close vision and ability to adjust focus. This would require the ability to lift and work with various materials and/or tools, as well as work and bend at different heights, in various temperatures, and be on feet for an extended period of time. Other Duties Please note this job description is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities that are required of the employee for this job. Duties, responsibilities, and activities may change at any time with or without notice. Qualifications Education and Experience * Experience using a variety of welding equipment and procedures (GTAW, FCAW-G) * Experience in using electrical or manual tools (saws, squares, calipers etc.) * Ability to read and interpret technical documents and drawings * Knowledge of relative safety standards and willingness to use protective clothing (face-shield, gloves etc.) * Minimum two years welding and fabrication experience * Professional Certification (AWS welding certificate) will be a plus EEOC Statement Equal Opportunity Employer/Veterans/Disabled Nikkiso CE&IG is proud to be an equal opportunity employer. We celebrate diversity and are committed to creating an inclusive environment for all employees. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, or protected veteran status and will not be discriminated against on the basis of disability.

POSSIBLE TRAVEL TO WISCONSIN WITH PER DIEM SUMMARY/OBJECTIVE The Pipe Welder JM2 assist pipefitter with fit-up of piping systems, accomplish welding piping onboard ship and shop fabrication for P- 2 piping. Welding need to pass all NDT's including hydrostatic testing. For production of Navy ship repair and other marine and commercial equipment. Pipe Welder JM2 must possess trade specific tools. ESSENTIAL FUNCTIONS / DUTIES Setup welding equipment Certified for all P-2 piping All welding must pass ndt's Fit and Tack parts together in preparation for welding Perform precise fitting work on components Running lines and leads Blueprint reading and interpret weld symbols Must adhere to a promote ALL company safety policies. Wear all required PPE when in Production areas and promote a clean and safe work environment. Ensure that employees assigned with Firewatch duties are in place and ready prior to begin hot work Fill out Job JSA forms Must adhere to a promote ALL company safety policies. Wear all required PPE when in Production areas and promote a clean and safe work environment. PHYSICAL DEMANDS The Pipe Welder JM2 must be able to meet and successfully perform the essential functions of this job. The following physical demands are representative to the position. The position is active and requires extensive standing, walking, sitting, bending, kneeling, stooping, crawling, climbing, and crouching. Along with such movements, employee is required to lift parts/machinery of up to 75 pounds. Additional demands are listed below: Able to climb ladders and work off scaffolding Able to lift, carry, and or push up to 50 - 75 lbs. throughout the shift (including overtime) * Reasonable accommodations may be made to enable individuals with disabilities to perform essential functions KNOWLEDGE / SKILLS Must be certified in Pipe Welding Ability to weld in all positions Ability to troubleshoot minor welding equipment problems Must be able to evaluate the use of various resources and make knowledgeable decisions regarding safety and company procedures and policies Able to read a tape measure Pass Welder Workmanship Training (WWT) Able to operate sawzall, 4” & 7” grinders, and various other tools Able to use Weld Gauges COMPETENCIES Communication Proficiency Flexibility (Job duties & schedule) Work well with others in all areas where SCW&M is performing work Follow verbal/written instructions Teamwork orientation SUPERVISORY RESPONSIBILTY Pipe Welder JM2 position has no supervisory responsibilities. POSITION TYPE / HOURS OF WORK This is a full-time position, 40 hours per week. Schedule is Monday- Friday, 6:00 a.m. to 2:30 p.m. / 2:30 p.m. to 11:00 p.m. (swing shifts dependent on work load). Occasional overtime and weekend work may be required based on production needs. REQUIRED EDUCATION AND EXPERIENCE Must be certified Pipe Welder Must have a minimum of 1-2 years of ship repair experience and/or skill set. Must be able to speak and understand Basic English Work Authorization Clearance For E-verify and contract security purposes (including ship access lists), all employees MUST present a valid export document. Acceptable documents are U.S. Birth Certificate, Certificate of Naturalization, Passport, Passport Card and Permanent Resident Card. Other Please consider that duties, responsibilities, and all other points specified in this description can change at any time with or without notice. Safety and responsible work practices are of SCW&M importance in everything we do. We are committed to employee safety & development, the protection of the environment and the communities where we operate. We are ready to be a partner in your career success!

Job Description: WelderJob Summary As a skilled welder, your primary jobs consist of welding together metal components as specified by blueprints, work orders, or instructions from management or a supervisor. The welder utilizes knowledge of working characteristics of metal and non-metal materials including the knowledge of the equipment to be used in the process. In the sequence of work activities, the welder's job follows that of the fitters, welding together structural components that have previously been fit and tacked into place.Major Duties & Responsibilities Operate tools and welding equipment including welders, cutters, torches, drills, grinders, and sanders. Set up parts and assemblies for welding, while configuring machines for different steel gauges of any types. Conduct measurements and quality checks, maintaining accurate records. Perform general labor operations such as load/unload parts, grinding, scraping, and nibbling fabrications. Essential Skills & Experience High school diploma, or equivalent. 3 years of welding experience. Proficiency in various welding techniques such as MIG, TIG, stick and flux-cored welding. Ability to interpret welding blueprints, drawings, and specifications. Understanding of welding equipment setup, operation, and maintenance. Safety & Environmental Factors: All employees are expected to adhere to the company's safety policies to maintain a safe and healthy work environment. This role involves working under extreme hot or cold conditions and requires the physical ability to stand for the entire shift, use hands for various tasks, ascend stairs, balance, stoop, kneel, crouch, talk, and hear. Team members must occasionally lift items weighing up to 50 lbs. Specific vision abilities required include close, distant, and peripheral vision, depth perception, and the ability to focus.Ameri-Force BenefitsAs part of the Ameri-Force team, a recognized ESOP company, you have a personal stake in the collective success of the organization, fostering a collaborative and rewarding work environment. Our competitive benefits package includes: Industry Leading Pay Medical Coverage Dental Coverage Vision Coverage Short-Term Disabilities Benefits Term Life Benefits Referral Bonuses *Referral Bonuses are available for specific jobs only About Ameri-Force Since 1991, Ameri-Force has been a leader in skilled trades staffing, offering a people-focused approach that provides competitive advantages for our clients and rewarding career opportunities for our contract employees. Our expertise in maritime, manufacturing, industrial, ensures a seamless experience by handling federal and state taxes, unemployment, and worker's compensation, along with offering comprehensive benefits such as medical, dental, vision, short-term disability, and life insurance. Join Ameri-Force and be part of a company that values your success. Learn more at ameriforce.com* Note: The specific duties, skills and qualifications may vary depending on the company's requirements and the nature of the tasks performed at the site. Employees must be willing to make reasonable adjustments to their tasks depending on the requirements of the client. We are an equal opportunity employer. We do not discriminate based on race, color, creed, religion, national origin, ancestry, citizenship status, marital status, age, sex, sexual orientation, gender identity, disability, veteran status, or any other protected characteristic as established by law.

CTR Group is seeking several Pipe Welder's local to the San Diego, CA area. Immediate openings and urgently hiring! What We Offer: Weekly Pay - you receive a paycheck every week Comprehensive Benefits Package Safety First! RESPONSIBILITIES: (may include but are not limited to) Read and interpret basic drawings and weld symbols Pass weld test for all Company weld procedures in the 6GR position Pass Company TIG weld test procedure for Carbon Steel, SS and CUNI pipe Work to Company housekeeping procedure Inspection of work, identification of potential problems, initiation of corrective actions Increase awareness of Quality procedures within department Perform as a productive working team member that meets daily goals set by the supervisor Continuously improve communications and flexibility within the team Help build the team environment Build pride of workmanship and quality through on job training Contribute towards innovation / productivity improvements Assist in the control of waste elimination, e.g. materials, consumables etc Assist supervisor to maintain control of department equipment and its maintenance Must have full set of personal tools Work towards the team goal of delivering the vessel on time Always be ready to start shift on time Follow Company guidelines and procedures Do not leave job early or return late from break times Ensure work area is left clean, all equipment and tools are stowed away safely and protected against damage REQUIREMENTS: (may include but are not limited to) Must be able to TIG Carbon, Stainless steel, and Copper Nickle Pipe Ability to pass “A Class” skills validation test to demonstrate welding ability for restricted open root welds Ability to successfully complete onboarding procedures in preparation to pass 6GR weld qualification test requirements for copper nickel, carbon steel and stainless steel to meet contract requirements for A Class welding on the vessel Must have the ability to bend, squat, stoop, crawl, and kneel Perform prolonged standing Ability to turn head from side to side and about the vertical axis Lift/push/pull 50lbs on an occasional basis Lift/push/pull up to 20lbs on a frequent basis Must have the ability to climb in a safe manner (climbing as a minimum includes stairs, scaffolding, ladders, and ramps) Ability to work at heights above 12' while working from ladders, scaffolding and/or man lifts Able to work at a variety of levels (ex. waist, eye, overhead) Demonstrate the ability to safely and appropriately use required tools and equipment Demonstrate good balance while working on uneven surfaces and maneuvering obstacles Possess sufficient handgrip and coordination to carry and operate tools and equipment Ability to utilize personal protective equipment (hard hat, safety glasses, steel-toes shoes, goggles, respirator, safety harness, safety line, flotation gear, etc.) safely per OSHA standards Ability to withstand cold and hot temperatures Ability to enter 18” x 36” openings and work in confined spaces for prolonged periods of time within OSHA guidelines Able to respond to verbal and audible sounds/commands Able to utilize adequate visual skills Ability to fully extend the arm while reaching overhead, reaching out, reaching to the side and reaching down Ability to perceive attributes of an object/material such as size, shape, temperature and texture by means of receptors in the hands and fingers The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job Must be able to tour all vessels and work sites While performing the duties of this job, the employee is regularly required to stand, walk, use hands to manipulate, handle, or feel, reach with hands and arms, climb and balance, stoop, kneel, crouch, or crawl, and talk or hear The employee is occasionally required to sit Candidates must meet the following employment eligibility guidelines to be considered for employment: 18 years of age or older at time of application Able to provide proof of US Person Status Willing to submit to a drug screen Willing to submit to a background check Must comply with company, federal, state, and local safety and environmental rules and regulations while performing daily job tasks About CTR Group: CTR Group operates in the staffing and recruitment industry, Nationwide for over 35 years. We provide full-service staffing support for various sectors including Marine Trades, Heavy Industrial, Light Industrial, Commercial, Technical, Professional, Aerospace and Aviation, and Energy. We offer a range of placement options such as Direct Hire, Contract Labor, Temporary & Temp to Hire. CTR Group takes pride in its high ratings across various platforms, reflecting our commitment to excellence and our dedication to providing quality staffing and employment services. CTR Group is an equal employment opportunity employer. Candidates are selected based on qualifications and defined requirements of the job, not on the basis of race, color, religion, sex, sexual orientation, gender identity, national origin or any other protected status. Further, CTR Group encourages United States' Veterans and persons with disabilities to apply for positions for which they are qualified.

Nikkiso Clean Energy & Industrial Gases is a leading provider of cryogenic pumps, heat exchangers, process systems, services, and solutions for the LNG and industrial gases industry. We are a subsidiary of Nikkiso Company Ltd, a leading industrial manufacturer headquartered in Tokyo, Japan, with over $1.5 B in annual revenue, 8000 + employees worldwide, and publicly traded on the Tokyo Stock Exchange. Nikkiso Cryoquip is a leading manufacturer of heat exchangers, liquefiers, and vaporizers for the LNG and industrial gases industry. Applications include fueling stations, marine engines, peak shaving, power generation, virtual pipelines, and well stimulation. Job Overview Summary We are looking for experienced welders that are able to perform advanced welding techniques (e.g., MIG, TIG,or Flux-Core) to join a variety of metals and alloys. Your job is important as it provides the foundation for strong infrastructure. A welder must be competent in using potentially dangerous equipment following all safety precautions. The ideal candidate will be able to produce welds that will pass visual and non-destructive testing inspections, and possess great attention to detail. Knowledge of different kinds of metal and their properties is essential. A weld test interview is required for this role. Rate $20/hr - $27/hr Responsibilities Essential Functions/Responsibilities Reasonable accommodation may be made to enable individuals with disabilities to perform the essential functions. Read and interpret blueprints, technical drawings, weld symbols and specifications to properly layout, fabricate and weld within allowable tolerance. Must be able to qualify in the 6G position with TIG. Set up, adjust, and operate welding equipment and tools safely and efficiently. Conduct visual and dimensional inspections of welds to ensure compliance with quality standards and codes. Perform intermediate-level fabrication and assembly work with minimal supervision. Experience with oxyacetylene and plasma cutting techniques, including torch setup, adjustment and safety practices. Weld components using manual or semi-automatic welding equipment in various positions (vertical, horizontal, or overhead) Able to determine that all welds meet ASME specifications Must produce x-ray quality welds with a high passing rate. Position requires overtime, including Saturday. Adhere to all safety guidelines, including the use of personal protective equipment (PPE) and safe work practices. Skills & Competencies Strong welding and fabrication skills with consistent quality. Attention to detail and ability to meet tight tolerances. Good problem-solving and troubleshooting ability. Effective communication and teamwork skills. Physical stamina to lift, bend, and stand for extended periods. Supervisory Responsibility This position has no direct supervisory responsibilities. Work Environment This job operates in a warehouse environment. This role routinely utilizes the operation of material handling equipment and various tools and machinery. Physical Demands While performing the duties of this job, the employee is regularly required to talk or hear. Specific vision abilities required by this job include close vision and ability to adjust focus. This would require the ability to lift and work with various materials and/or tools, as well as work and bend at different heights, in various temperatures, and be on feet for an extended period of time. Qualifications Education and Experience Experience using a variety of welding equipment and procedures (GTAW, SMAW, FCAW) Experience in using electrical or manual tools (saws, squares, calipers etc.) Ability to read and interpret technical documents and drawings Knowledge of relative safety standards and willingness to use protective clothing (face-shield, gloves etc.) Minimum five years welding and fabrication experience Professional Certification (AWS welding certificate) will be a plus Other Duties Please note this job description is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities that are required of the employee for this job. Duties, responsibilities, and activities may change at any time with or without notice. EEOC Statement Equal Opportunity Employer/Veterans/Disabled Nikkiso CE&IG is proud to be an equal opportunity employer. We celebrate diversity and are committed to creating an inclusive environment for all employees. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, or protected veteran status and will not be discriminated against on the basis of disability.

Phillips Tank & Structure (PTS) is no ordinary tank construction company. We specialize in the complex and fast-paced environment of tank repair on a nationwide scale. No two tanks are alike, so when they need repair, they often pose unique or complicated technical issues. Our experienced engineering staff are well-versed in API 650, API 653, AWWA D100, AWWA D103, API 12D, and other tank specifications. We build and repair welded above-ground storage tanks (ASTs), bolted tanks, and related structures. We also inspect, install, and repair tank systems such as aluminum geodesic dome covers, aluminum internal floating roofs (IFRs), IFR mechanical shoe seals, liquid level gauges, fire protection systems, silo support structures, industrial storage tanks, and heating and insulation systems. Statement of Purpose To provide satisfying, long-term work opportunities for our dedicated employees - We believe that there is pride to be gained in performing productive work, and there should be great satisfaction in achieving results as a team. Our efforts will be spent towards continuously improving the health, strength, and quality of the company. We believe our collective success will generate value that supports our families and benefits our communities. The PTS difference: Our people are our #1 priority. Teamwork is the best way to solve problems. Safety is critical. Everyone is responsible for creating a safe work environment. We strive to find new and better ways of doing things every day. Clear expectations and directions are always given. Frequent coaching and support lead to great performers and high quality for our customers. A manager's job is to set each employee up for success every day. We don't punish people for mistakes - we work together to understand the root cause of a mistake and solve it together. We strive to create an environment where you look forward to coming to work each day and leave work with a sense of pride and accomplishment. Day to Day Duties: Performing arc and torch cutting and gouging. Using generators, compressors, tuggers, blowers, grinders, and other power and air tools. Welding plate with 7018, 7024 and 6010 stick (SMAW), flux core (FCAW), and submerged arc automatic machines (3 o'clock and “goat”/tractor). Using come-alongs, hydraulic jacks, hoists, air bags, winches, and other lifting equipment. Using tank shell buggies, tank scaffolding, tank ladders, and other specialty equipment. Performing vacuum box tests, oil tests, dye penetrant tests, and other non-destructive quality examinations. Using gas monitors, fresh air kits, respirators, emergency rescue kits, and other safety equipment. Operating forklifts, man lifts, boom lifts, and other large lifting equipment. Knowledge of crane operations (including rigging and signaling) Reading detailed erection and fabrication drawings. Planning the sequence and methods of fitting up, welding, repairing, and constructing tanks. Completing job safety analysis, safety audits, site-specific training, and other safety training. Follow directions and work professionally with other crew members. Other duties as assigned. Requirements Have great communication and organization skills. The ability to solve problems and suggest improvements to our systems. Have excellent attendance and show up to work on time every day. The willingness to learn. Be at least 18 years old. Be able to lift 50 lbs. Have a high school diploma or equivalent. Be eligible to work in the United States. Be willing to authorize background checks. Have no criminal convictions for dishonesty, sexual misconduct, violence, or acts of terrorism. Have a valid driver's license. Be willing to authorize motor vehicle driving record checks. Be willing to submit to pre-hire, random, and post-incident drug and alcohol testing. Ability to weld is a plus. Benefits: Competitive Pay with annual reviews Health, Dental and Vision insurance 401k with company match Great culture of teamwork, learning and development. You'll be part of a team where YOU matter

TempToFT Job Title: Welder / Pipe Welder Pay: $20 - $30 per hour Schedule: Monday - Friday, 7:00 AM - 4:00 PM (some Saturdays for overtime) About the Company: Key Staffing is hiring a Welder to join a growing company that supplies new, used, and surplus pipe. Their goal is to retain and develop employees who are motivated, team-oriented, and eager to grow with the company. They value individuals who take initiative, work independently when needed, and contribute to a positive team environment. Job Description: We are seeking a talented Welder / Pipe Welder with experience in GMAW (MIG) and flux core welding, primarily on stainless steel. The ideal candidate will be certified in D1.1, with structural welding experience preferred. Responsibilities: Perform welding on stainless steel using flux core and GMAW techniques. Cut, grind, and prepare materials independently. Work outdoors approximately 85% of the time. Follow all safety procedures and company policies. Collaborate with team members to complete projects efficiently. Take initiative to troubleshoot and complete work independently when needed. Requirements: GMAW welding experience required. FCAW welding experience required. D1.1 welding certification preferred; structural welding experience preferred. Ability to cut and grind materials independently. Strong team-oriented mindset; able to get along with others and contribute to a positive work environment. Self-starter with a strong work ethic and desire to grow with the company. Long-term commitment to the company is highly valued. What We Offer: Monday - Friday schedule with some overtime on Saturdays. Opportunity to grow with a stable and supportive company. Team-focused work environment. Commitment to Diversity: As an equal opportunity employer committed to meeting the needs of a multi-generational and multicultural workforce, Key Staffing recognizes that a diverse staff, reflective of our community, is an integral and welcome part of a successful and ethical business. We hire local talent at all levels regardless of race, color, religion, age, national origin, gender, gender identity, sexual orientation, or disability and actively foster inclusion in all forms both within our company and across interactions with clients, candidates, and partners. If this position caught your eye, send us your resume! For best consideration, include the job title and source where you found this position in the subject line of your email to cbalz@hirekeystaff.com 30.00

Description Now hiring-SPOT WELDERColtonMonday-Friday 5AM-1:30PMPay rate: $17h/rSpot welding- will be trained Will be welding small pieces of A/C units together Strong attention to detail TEMP TO HIRE-UNION BENEFITS**Contact us today618 S MT Vernon AveSuite 130San Bernardino, CA 92410(909)238-5848We are now accepting ONLINE applications WWW.SYNCSTAFFINGSERVICES.COMGive us a call after completing the application Follow us on Instagram!Syncstaffing_CA Type: Full-time