Numerical control operator jobs in Lexington, SC

The TFE Operator will be responsible for machine operation. This would include troubleshooting, documentation, and quality of material.

NORMAL DUTIES include the following. Not all tasks are performed on all sections due to automation on some equipment. · Complete paperwork as required. · Responsible for quality and machine speed.(caliper, etc, bonding, scoring, size) · Responsible for coater operation - including pumps, coolers, filters · Responsible for impregnator and its operation · Prepare coater/impregnator for runs · Ensure there is sufficient coating for the day's runs, as well as ensure management is aware of low inventory of totes. · Daily, weekly, monthly cleaning of machines at wet end. · Ensuring machine is running at the appropriate speeds required. · Housekeeping of coater/impregnator and its associated areas. · Monitoring coater for proper settings and quality of board produced · Must be able to operate a) singlefacers/doublebacker, b) roll stands, and c) splicers. · Must be able to: a) control coating waste, b) control paper waste, c) trouble-shoot quality problems, and d) maintain proper setting on coater. · Must maintain a high level of housekeeping on, in and around the coater. Must not be afraid of heights, machine has two levels · Report any maintenance problems as required. The Operator will also perform any other duties as assigned. QUALIFICATION REQUIREMENTS: To perform this job successfully, an individual must have demonstrated the ability to perform each normal duty satisfactory in this and all lower classifications in this line of progression. The requirements listed below are representative of the knowledge, skill, and/or ability required. EDUCATION and/or EXPERIENCE: High School diploma or general education degree (GED); or five years related experience and/or training; or equivalent combination of education and experience. LANGUAGE SKILLS: Ability to read and interpret written documents such as safety rules, operating and maintenance instructions, factory orders, and procedure manuals. Ability to write routine reports and correspondence. Ability to communicate effectively. MATHEMATICAL SKILLS: Ability to add, subtract, multiply, and divide in all units of measure (English and Metric systems), using whole numbers, common fractions, and decimals. Ability to read an English and metric system tape measure. REASONING ABILITY: Ability to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization may exist. Ability to interpret a variety of instructions furnished in written, oral, diagram, or schedule form. PHYSICAL DEMANDS: The physical demands described here are representatives of those that must be met by an employee to successfully perform normal job functions. While performing the duties of this job, an individual is regularly required to stand; use hands to finger, handle, or feel objects, tools, or controls; reach with hands and arms; talk or hear; and taste or smell. An individual frequently is required to stoop, kneel, crouch, or crawl. An individual must regularly lift and/or move up to ten pounds, frequently lift and/or move up to twenty-five pounds, and occasionally lift and/or move up to fifty pounds. Specific vision abilities required by this job include close vision, color vision, peripheral vision, depth perception, and the ability to adjust focus. WORK ENVIRONMENT: The work environment characteristics described here are representative of those an individual encounters while performing the normal job functions. While performing the duties of this job, an individual regularly works near moving mechanical parts. The employee is occasionally exposed to wet and/or humid conditions and temperature variations. The noise level in the work environment is usually moderate. Reasonable accommodations may be made to enable individuals with disabilities to perform the normal job functions.

Title: CNC Machine Operator-Large Parts We are offering a $3,000.00 Sign on Bonus Pioneer the next generation of innovation. Join us and you'll develop your skills and expertise to the very highest levels, working in an international environment for a company known the world over for its brilliance. Key Accountabilities: Operate Computer Numerical Control (CNC) HELLER machining centers with Siemens 840 D Controllers according to instructions, routings, control plans, production requirements, plans and diagrams. Study machining instructions, routings, control plans, job orders, and blueprints to determine dimensional and finish specifications, sequences of operations, complex machine setups, and tooling requirements. Select the appropriate tools, and materials to be used in preparation of cubic engine components. Set up, adjust, and operate all of the basic machine tools and many specialized or advanced variation tools to perform precision machining operations. Check precision measuring instruments such as calipers, micrometers, fixed and telescoping gauges, templates and fixtures, and adjust according to quality control plans. Perform fine-tuning of tools/equipment through sample cuts and optimize the CNC program in regard to tool durability, preventing the collision of tools/equipment, program sequencing. Observe machines operation in order to detect sounds such as those made by dull cutting tools or excessive vibration and adjust machines to compensate for problems. Stop machines to remove finished work pieces, or to change tooling, setup, or work piece placement, according to required machining sequences. Measure dimensions of finished work pieces to ensure conformance to specifications, using precision measuring instruments. Maintain industrial machines within the scope of Total Productive Maintenance (TPM) specifications, applying knowledge of mechanics, shop mathematics, metal properties, layout, and machining procedures. Comply with safety regulations and maintain clean and orderly work areas. Identify and reduce non-value-added work. Perform special projects as may be required and maintain on the job flexibility by providing support in other production related areas. Promote a compliance culture in area of responsibility and live the letter and the spirit of the Rolls-Royce Code of Conduct. Basic Requirements: 2 years in a mechanical, maintenance or machining trade school or equivalent Associate's Degree; or 3 years of experience in a heavy-duty machining environment. Ability to work overtime as required. This position is scheduled for the Mini Shift which starts at 5:45am and ends at 6:15pm, Friday through Sunday. Initial training may occur on 1st shift from 5:45am to 4:15pm, Monday through Thursday, until training is completed. "Applicants must be authorized to work for any employer in the U.S without sponsorship. We are unable to sponsor or take over sponsorship of an employment Visa at this time.” Preferred Qualifications: Experience as a CNC milling operator. Knowledge of SIEMENS 840 D Control System Ability to obtain appropriate hoists and power vehicle licenses (Flatbed, Hi-Lo, & Mule) when necessary Intermediate knowledge of CNC-controls (preferred SIEMENS 840 D Controllers) machines and tools, including their designs, uses, repair, and maintenance. Intermediate knowledge of arithmetic, algebra, geometry, calculus, statistics and their applications Basic ability to interpret Statistical Process Control (SPC) and operate scanning devices for system communications. Basic knowledge of manufacturing and production processes, raw materials, quality control, costs, and other techniques for maximizing the effective manufacture of goods (Quality Alerts, Second Checks, etc.) Basic knowledge of OSHA safety requirements and the ability to use relevant information and individual judgment to determine whether events or processes comply with laws, regulations or standards. Basic troubleshooting and problem-solving skills where problems are complex. Basic interpersonal skills and the ability to work effectively with other employees. Basic ability to interpret blueprints, build documents, schematic drawings, layouts or other documents regarding engine assembly and testing. Basic organizational, planning and follow-up skills and the ability to cope with stress. Basic oral and written communication skills Basic reading, writing and math skills. Ability to work any shift and overtime as required. Basic PC knowledge and the ability to efficiently operate computer terminals, tools and devices. Work Environment: Reasonable accommodations may be made to enable individual with disabilities to perform the essential functions. Daily work is performed in a durable goods manufacturing environment. While performing the duties of this job, the employee is frequently required to walk and stand; sit, use hands or fingers, handle, or feel objects, tools, parts, or controls reach with hands and arms; and talk or hear. The employee is occasionally required to balance and climb; stoop, kneel, crouch or crawl. The employee must regularly lift and/or move up to 10 pounds, frequently lift and/or move up to 25 pounds, and occasionally lift and/or move up to 50 pounds. Specific vision abilities required by this job include close vision, distance vision, peripheral vision, and depth perception. The employee may also be exposed to any number of elements but with none present to the extent of being disagreeable. Rolls-Royce is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to any protected characteristics. At Rolls-Royce, we are committed to creating a workplace where all employees feel respected, supported, and empowered to do their best work. We foster a welcoming and innovative work environment that invests in you, giving you access to an incredible breadth and depth of opportunities where you can grow your career and make a difference. Job CategoryFactory Staff Job Posting Date12 Dec 2025; 00:12 Pay Range$22.89 - $34.33-Hourly Location: Graniteville, SC Benefits Rolls-Royce provides a comprehensive and competitive Total Rewards package that includes base pay and a discretionary bonus plan. Eligible employees may have the opportunity to enroll in other benefits, including health, dental, vision, disability, life and accidental death & dismemberment insurance; a flexible spending account; a health savings account; a 401(k) retirement savings plan with a company match; Employee Assistance Program; Paid Time Off; certain paid holidays; paid parental and family care leave; tuition reimbursement; and a long-term incentive plan. The options available to an employee may vary depending on eligibility factors such as date of hire, employment type, and the applicability of collective bargaining agreements.

Salary Range: $40,000.00 to $50,000.00 About SKF: SKF, reducing friction since 1907, re-imagining rotation for a better tomorrow! SKF is an industry-leading manufacturer that has been a cornerstone in industrial life. Wherever there are machines or products in motion, SKF bearings are there to reduce friction. SKF drives the industries that support our way of life, powers the machines that put food on the table, and even helps explore the cosmos. Sustainability is at the heart of everything we do. SKF is on pace to decarbonize all its production facilities by 2030. We're guided by our SKF values. Collaboration is critical to the success of our colleagues, partners, and customers. Curiosity and Courage provide a foundation for innovation and advancement. And we do this work out of Care for our people, customers, communities, and the planet. We're a company committed to a culture of belonging, where all our people are encouraged to be themselves and grow their careers in an equitable environment. Learn about SKF at ************ Summary: The primary function of this position is the efficient set-up, operation and troubleshooting of CNC machining centers ensuring the proper machining techniques are followed and acceptable levels of quality and productivity are met within established parameters in a safe and effective manner. Duties and Responsibilities (included but not limited to): * Starts up and shut down a variety of machine(s) following established company procedures and safety guidelines. * Sets up and operates numerically controlled (NC, CNC, PLC and other manual machines) lathes (horizontal & vertical) performing machining operations including: turning, boring and facing castings and forgings. Selects and installs tooling into tool posts, turrets or indexing heads. * Mounts work piece in chuck, or faceplate, manually or using hoist or cranes. * Performs machining operations on a variety of parts at times with high levels of complexity, ensuring machining operations are performed within established parameters, minimizing scrap and rework with acceptable levels of output. * Reads and interprets a variety of engineering and quality specifications. * Applies practical and working knowledge of machines to make the necessary adjustments (turning dials, switches, and assigned offset/program controls) to override machine control and correct machine performance. * Responsible for all inspections ensuring conformance to specifications using precision measuring instruments. May also perform inspections for other operators if required. * Observes numerical displays on control panel and compares with data on process sheet to verify dimensional adjustments, feed rates and speed of machining cuts. * Performs continuous improvement (lean) activities as may be assigned or required. * Performs other duties and assignments as scheduled and/or required. Requirements/Qualifications: * High School diploma or GED equivalent is required. Technical degree in manufacturing technology preferred. * One (1) to three (3) years machining experience in precision manufacturing environment. * Solid understanding and ability to use shop math and precision (micrometers, precision dial gauges, etc.) measuring instruments. * A thorough knowledge of CNC machine operation, tool off setting and basic machine code is strongly preferred. * Responsible for maintaining a clean and safe environment including identification of unsafe conditions. Steel toed shoes and ANSI approved safety glasses with side shields must be worn at all times. * Must be able to read, write, understand technical documentation, computer literate, read process drawing (blueprints), and engineering specification. * Responsible for maintaining a clean and safe environment including identification of unsafe conditions. Ergonomics/Physical: * Varied postures - sitting, standing, leaning forward, turning side to side * Transports product from one area to another * Use of Hand Carts - pushing * Use of Hoist - pulling * Standing, Sitting, walking in general * Pushing, carrying, or lifting to max. 40 lbs. occasionally What You'll Love About SKF:Rest and Relaxation. Enjoy a generous PTO policy and 13 paid holidays. Work/Life Integration. SKF supports work/life integration, home, family, community, personal well-being and health. Diversity in the Workplace. ?At SKF, we strive to embed Diversity, Equity and Inclusion in everything we do. By developing a culture of belonging, our people can flourish; leading to an inclusive, equitable environment that promotes leadership, engagement and innovation. Best in Class Benefits. SKF cares about the wellbeing of our employees. Comprehensive healthcare options to fit your needs and opt out payment. Added benefits include company paid life insurance, STD, LTD. Supplemental benefits include critical illness coverage, tuition reimbursement, employee discount programs, and much more! Bonus. SKF offers STVS (Short Term Variable Salary) or Sales Incentive based on company performance and at the discretion of management. Invest in your Future. Participate in our 401K program that boasts a 10% employer contribution: 100% match up to 5% of your elected contribution (100% Vested) plus an additional 5% company contribution. Reports to: Channel Manager Location: Sumter, Sc Job ID: 23368 SKF provides equal employment [and affirmative action] opportunities to applicants and employees without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, protected veteran status, or disability. By applying to this job you acknowledge how SKF treats candidate data. Click HERE to review the SKF Data Privacy Consent Statement.

Job Type: Full-Time | Evening/Night Shift | In-Person Schedule: 40 hours per week | Monday-Friday, 5pm-1:30am with a 30-minute lunch break Pay: From $20.00 per hour Who we are: Sorinex Exercise Equipment, based in Lexington, SC, is a leader in fitness equipment manufacturing and innovation. For over 40 years, we've built the highest-quality gym and strength training equipment for home gyms, college athletics, professional sports teams, and the U.S. military. As we continue to grow, we're hiring motivated individuals to join our team through direct-hire opportunities. If you're looking for a career where you can grow and excel, apply now! Who we are looking for: We are looking for a skilled and detail-oriented CNC Machine Operator to safely perform laser cutting and machine operations for a wide range of products. Success in this role will require the ability to produce consistently accurate work and efficiently take verbal direction with minimal supervision. The ideal candidate will be able to work independently while reading and interpreting blueprints, diagrams, engineering drawings, and other instructions. We are looking for someone who can: Perform laser cutting operations with precision and efficiency. Choose the appropriate cutting programs to match specific job requirements. Accurately set up equipment for cutting operations to ensure optimal performance. Carry out necessary maintenance duties to keep the laser equipment in peak condition. Inspect the quality and dimensions of cuts to meet exact specifications. Load and unload materials, and efficiently sort parts for the next stages of production. Follow standardized work processes, ensuring correct documentation and procedures are maintained. Produce consistently accurate work on a daily basis. Occasionally lift items weighing over 50 pounds as part of the job requirements. Take verbal direction with minimal assistance and complete tasks efficiently and independently. Read, interpret, and follow blueprints, diagrams, engineering drawings, bills of materials, and other instructions with ease. Maintain a safe, clean, and organized work area at all times. Be prepared to take on additional tasks as production needs arise. Perform all other duties as assigned. Physical Demands: Lift, carry, push, and/or pull 1-50 lbs. frequently Squat/kneel, bend/stoop, crawl, twist/turn, grasp, and reach overhead and outward frequently Sit, stand, and walk for 1-10 hours per day Work in a fast-paced industrial environment wearing hearing protection, eye protection, steel-toed shoes, and other appropriate protective clothing Required Experience: CNC Operator: 2 years (preferred) Machining: 2 years (preferred) Benefits: 401(k) 401(k) Matching Dental Insurance Health Insurance Life insurance Paid time off Vision insurance

Job Description Experienced CNC Machinist needed for busy job shop. Must be able to independently setup and run CNC lathes and mills. Requires a minimum of 2 years of experience with Fanuc and/or Haas controls and a high school diploma or equivalent. Tech school graduate preferred. Requires excellent work ethic, consistent work history, and the ability to work overtime as needed. First shift position in a climate controlled shop. Must be able to comfortably lift 50+ lbs. Pay Rate: $20.00 - $28.00/hr

As a Gantry Mill Machinist at Husqvarna Construction in Columbia, SC, you will work in the Tool Room within the manufacturing area. You'll use your knowledge of metal properties and machining techniques-such as milling, drilling, reaming, and boring-to plan and perform operations that produce parts meeting exact blueprint and routing specifications. SHIFT: 2nd shift, 2:30 p.m. - 11:00 p.m., Monday - Friday The primary machining operation will be modification of steel blade cores, and the primary machine tool will be the Haas Gantry Milling machine. You will set up the machine, choose cutting tools, and write or modify basic CNC programs. During and after the machining operations, you will use precision measuring tools to perform quality control checks and ensure compliance to blueprints or routing requirements. When defects are detected, you will make corrections as needed. Other tasks will include cleaning and storage of tooling, cleaning of machines, and cleaning of the work area. ESSENTIAL FUNCTIONS * Set-up of Haas Gantry Milling machine and fixtures * Writing and editing basic CNC programs * Machining steel blade cores per blueprint requirements * Quality control of machined products * Correction of defective machining conditions * Basic maintenance and cleaning of the Haas Gantry Milling machine and fixtures * Basic maintenance and cleaning of the department floors and walls PLEASE NOTE: The gantry milling operation is not limited to these procedures and additional responsibilities may be added as deemed necessary by management. The equipment of this job description includes and is not limited to: * Haas Gantry Milling Machine * Work holding fixtures * Cutting, milling, and drilling tools and holders * Misc. measuring devices such as micrometers, dial and/or digital indicators, and calipers KNOWLEDGE, SKILLS & ABILITIES The Gantry Milling Machinist must demonstrate ability and /or experience in the following areas: * High School Diploma or GED with course work and training in machine tool technology or confirmed job experience working with metal removal equipment. * Two (2) years minimum machine shop training and one (1) year machine shop experience required. CNC Operator/ Programming Certificate preferred. * Basic set-up and operation of CNC controlled metal removal equipment. Must understand basic M Code and G code programming. Experience with other metal removal machines and grinders will be accepted but the candidate must demonstrate set-up and operation knowledge. One (1) year minimum experience required. * Must be able to correctly interpret engineering mechanical drawings. Must understand machining properties of metals * Must understand the metal removal concepts of milling, drilling, reaming, and boring. * Must understand selection of machine speeds and feeds for each machining operation * Must understand the metric system of measurement. * Correct usage of quality control measuring equipment such as micrometers, dial indicators, and calipers. * Basic shop math to include Addition, Subtraction, Multiplication, Division, Fractions, Decimals, Geometry and Trigonometry * Lifting of up to 60 lbs. * Must be able to handle multiple projects simultaneously. * Must excel at working in a team environment. WORKING CONDITIONS * Air-conditioned factory with concrete industrial floor * This job requires standing at all times. * Job tasks will require contact with powder metal segments, sharp edges on machined components, and grime associated with machining operation. Gloves and other protective gear will be provided as needed. * Light industrial noise level when machines in operation * Room is lighted for medium precision industrial operations * Required to wear safety glasses and steel toe shoes while working in the manufacturing areas. * Overtime and Saturday work may be required with minimum 24-hour notice. WE OFFER: * Competitive compensation * Benefits, including medical, dental, and vision insurance at date of hire * A 401(k) with matching and no vesting * An employee purchase discount on Husqvarna products * An education assistance program * Paid parental leave * 11 Paid holidays * Paid vacation and sick time Husqvarna is an Equal Employment Opportunity employer committed to providing equal opportunity in all of our employment practices, including selection, hiring, assignment, re-assignment, promotion, transfer, compensation, discipline and termination. Husqvarna prohibits discrimination, harassment and retaliation in employment based on race; color; religion; national origin; gender; sexual orientation; pregnancy; age; disability; service member status; or any other category protected by federal, state, or local law. Last date to apply: We are continuously accepting applications

As a Gantry Mill Machinist at Husqvarna Construction in Columbia, SC, you will work in the Tool Room within the manufacturing area. You'll use your knowledge of metal properties and machining techniques-such as milling, drilling, reaming, and boring-to plan and perform operations that produce parts meeting exact blueprint and routing specifications. SHIFT: 2nd shift, 2:30 p.m. - 11:00 p.m., Monday - Friday The primary machining operation will be modification of steel blade cores, and the primary machine tool will be the Haas Gantry Milling machine. You will set up the machine, choose cutting tools, and write or modify basic CNC programs. During and after the machining operations, you will use precision measuring tools to perform quality control checks and ensure compliance to blueprints or routing requirements. When defects are detected, you will make corrections as needed. Other tasks will include cleaning and storage of tooling, cleaning of machines, and cleaning of the work area. ESSENTIAL FUNCTIONS Set-up of Haas Gantry Milling machine and fixtures Writing and editing basic CNC programs Machining steel blade cores per blueprint requirements Quality control of machined products Correction of defective machining conditions Basic maintenance and cleaning of the Haas Gantry Milling machine and fixtures Basic maintenance and cleaning of the department floors and walls PLEASE NOTE: The gantry milling operation is not limited to these procedures and additional responsibilities may be added as deemed necessary by management. The equipment of this job description includes and is not limited to: Haas Gantry Milling Machine Work holding fixtures Cutting, milling, and drilling tools and holders Misc. measuring devices such as micrometers, dial and/or digital indicators, and calipers KNOWLEDGE, SKILLS & ABILITIES The Gantry Milling Machinist must demonstrate ability and /or experience in the following areas: High School Diploma or GED with course work and training in machine tool technology or confirmed job experience working with metal removal equipment. Two (2) years minimum machine shop training and one (1) year machine shop experience required. CNC Operator/ Programming Certificate preferred. Basic set-up and operation of CNC controlled metal removal equipment. Must understand basic M Code and G code programming. Experience with other metal removal machines and grinders will be accepted but the candidate must demonstrate set-up and operation knowledge. One (1) year minimum experience required. Must be able to correctly interpret engineering mechanical drawings. Must understand machining properties of metals Must understand the metal removal concepts of milling, drilling, reaming, and boring. Must understand selection of machine speeds and feeds for each machining operation Must understand the metric system of measurement. Correct usage of quality control measuring equipment such as micrometers, dial indicators, and calipers. Basic shop math to include Addition, Subtraction, Multiplication, Division, Fractions, Decimals, Geometry and Trigonometry Lifting of up to 60 lbs. Must be able to handle multiple projects simultaneously. Must excel at working in a team environment. WORKING CONDITIONS Air-conditioned factory with concrete industrial floor This job requires standing at all times. Job tasks will require contact with powder metal segments, sharp edges on machined components, and grime associated with machining operation. Gloves and other protective gear will be provided as needed. Light industrial noise level when machines in operation Room is lighted for medium precision industrial operations Required to wear safety glasses and steel toe shoes while working in the manufacturing areas. Overtime and Saturday work may be required with minimum 24-hour notice. WE OFFER: Competitive compensation Benefits, including medical, dental, and vision insurance at date of hire A 401(k) with matching and no vesting An employee purchase discount on Husqvarna products An education assistance program Paid parental leave 11 Paid holidays Paid vacation and sick time Husqvarna is an Equal Employment Opportunity employer committed to providing equal opportunity in all of our employment practices, including selection, hiring, assignment, re-assignment, promotion, transfer, compensation, discipline and termination. Husqvarna prohibits discrimination, harassment and retaliation in employment based on race; color; religion; national origin; gender; sexual orientation; pregnancy; age; disability; service member status; or any other category protected by federal, state, or local law. Last date to apply: We are continuously accepting applications

GENERAL SUMMARY: Coordinates activities of workers engaged in setting up and operating arc welding machine that seam-welds rolled plate to form large diameter spiral fabricated pipe by performing the following duties. MINIMUM QUALIFICATIONS: To perform the job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. ESSENTIAL FUNCTIONS/RESPONSIBILITIES: include the following: (Other duties may be assigned, including but not limited to cross training and housekeeping. Responsibilities also include attention to safety according to all safety rules.) In addition to the duties of cutoff, tracker and floor: In conjunction with department team leader, reviews daily work schedule and specification sheets for current material and process requirements; directs and assists crew members with setup for daily runs. Ensures mill machine is kept running by observing and correcting problems that arise. Monitors quality of alignment and weld process. Monitors and resolves employee issues; conducts and/or recommends employee discipline if required. Performs preventive maintenance and minor repairs to mill machinery and equipment. Refers electrical and hydraulic problems to maintenance department for resolution. Develops, recommends, and implements measures to improve production methods, equipment performance, and quality of product. Brings safety issues to the attention of department manager or safety manager. Loads coils onto the back of machine. Verifies that all positions have been checked and ready to start. Performs other tasks as instructed by supervision. PHYSICAL/ENVIRONMENTAL REQUIREMENTS: While performing the duties of this job, the employee is regularly required to stand, walk, use hands to finger, handle, or feel and talk or hear. The employee is frequently required to stoop, kneel, crouch, or crawl. The employee is occasionally required to sit, reach with hands and arms and climb or balance. The employee must regularly lift and/or move up to 10 pounds, frequently lift and/or move up to 25 pounds and occasionally lift and/or move up to 100 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision and ability to adjust focus. WORK ENVIRONMENT: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly exposed to moving mechanical parts. The employee is frequently exposed to fumes or airborne particles. The employee is occasionally exposed to extreme heat. The noise level in the work environment is usually loud.

Job DescriptionDescription: INDEVCO North America (INA) is seeking a skilled and experienced Extrusion Operator specialized in Blown Film production to join our manufacturing team. The ideal candidate will be responsible for the efficient operation of extrusion machinery, ensuring the production of high-quality blown film products. The Extrusion Operator will play a crucial role in maintaining optimal machine performance, troubleshooting issues, and adhering to safety and quality standards. Key Responsibilities: Operate and monitor blown film extrusion machinery to produce quality film products according to production specifications. Set up, adjust, and control machine settings, such as temperatures, speeds, and thickness, to achieve desired product characteristics. Conduct routine equipment checks and preventative maintenance to ensure continuous and efficient operation. Monitor product quality throughout the production process, making necessary adjustments to maintain consistent quality standards. Conduct visual inspections and measurements of finished products to ensure they meet customer and company specifications. Troubleshoot and address any issues related to product defects or deviations from quality standards. Adhere to all safety protocols and guidelines to ensure a safe working environment. Operate machinery in compliance with company policies, industry regulations, and quality standards. Report any safety incidents, equipment malfunctions, or maintenance needs promptly. Maintain accurate production records, including machine settings, production rates, and quality control data. Complete required documentation and reports in a timely and accurate manner. Requirements: High school diploma or equivalent. Additional technical or vocational training in extrusion operations is a plus. Proven experience as an Extrusion Operator, with a focus on blown film production. Familiarity with the operation and maintenance of blown film extrusion machinery. Ability to set up, operate, and troubleshoot blown film extrusion equipment. Basic understanding of mechanical and electrical systems related to extrusion machinery. Strong attention to detail and commitment to producing high-quality products. Knowledge of safety procedures and a commitment to maintaining a safe work environment. Effective communication skills, both verbal and written. Ability to work collaboratively in a team environment. Ability to lift and move heavy materials as needed. Comfortable working in a manufacturing environment with exposure to noise, dust, and varying temperatures. At INDEVCO, we provide our employees with a highly competitive benefits package, including life, medical, and dental insurance coverage, a 401(K)-matching plan, paid vacation, and an Employee Tuition Reimbursement benefit for professional certifications and degree programs. INDEVCO North America, Inc. is an equal opportunity employer. We embrace diversity and are dedicated to fostering an inclusive environment for all our employees.

Tool Room Technician Blythewood, SC, US ABOUT STANADYNE: Stanadyne is known around the world as a leading supplier of diesel fuel systems and components. In addition, Stanadyne is quickly becoming an industry leader in the fast-growing field of Gasoline Direct Injection (GDI). Our products are for engine applications in agriculture, construction, power generation, industrial, marine, and on-highway vehicles. Over the years Stanadyne has expanded with precision manufacturing locations in China, India, Italy, and the United States. We have been providing innovative fuel system solutions to our customers for over 50 years and continue to focus on developing future cutting-edge fuel systems that will help distinguish our customers' engines from their competition. Our Jacksonville manufacturing facility has about 250 employees operating over three shifts. POSITION SUMMARY: The Prototype Machinist - Tool Room Technician provides precision-machining support, grinding, milling/turning conventional and CNC. For the purpose of achieving business and production goals, including safety, quality, delivery and cost. RESPONSIBILITIES: * Analyzes complex machining needs; determines tools, equipment and materials. needed, plan and carry out highly involved work projects. * Manufactures high quality precision details and parts on tool room equipment. * Works with all internal customers to develop fixtures and tooling and production methods. * Completes set ups on tool room and prototype equipment. * Ability to read and correctly interpret mechanical drawings, prints and GD&T. * Maintain a clean and organized work area and conducts all work in a safe and efficient manner. * Ability to effectively work in a team environment * Experience working with AutoCad, Solid Works, Creo and CAM software QUALIFICATIONS: * At least 5 years of CNC machining experience * At least 5 years Tool Maker experience * Master Cam preferred. * Passionate customer focus * Thoughtful, fast, disciplined execution * A commitment to continuous improvement * A relentless drive to succeed EDUCATION / EXPERIENCE: * High School Diploma or G.E.D. Note: The above statements are intended to describe the general nature and level of work being performed by people assigned to the classification. They reflect the essential elements and general responsibilities of the position but are not intended to be construed as an exhaustive list of all responsibilities, duties and skills required of personnel so classified.

Harsco is recognized for technical leadership and worldwide experience in virtually all major aspects of railway track maintenance. We enable railroads to operate at peak efficiency over smooth, precisely aligned track that increases railway safety while reducing fuel consumption and other key operating costs. Our broad array of equipment and services support every type of railway operator, from major national and international railway systems to short lines and high-speed urban transit networks. Reporting to the Machining Supervisor, the Machinist A is responsible for performing advanced machining operations with a high degree of precision, efficiency, and safety. This role requires expert knowledge of machining practices, strong technical skills in CNC programming and setup, and the ability to produce quality parts that meet engineering specifications and production requirements. Key Responsibilities Demonstrate expert-level knowledge of machining practices, including part creation, quality assurance, and safe work methods. Independently interpret complex blueprints and technical drawings. Set up, program, and operate CNC lathes, vertical mills, and horizontal mills. Write CNC programs from scratch, select appropriate tooling, and verify part quality to specification. Apply advanced knowledge of machine tools, feeds, speeds, and tooling applications to optimize machining processes. Adjust and edit CNC programs and offsets as required to maintain precision tolerances. Collaborate with process engineering to develop setup sheets, document programs, and support future repeatability. Maintain production goals while upholding strict quality standards. Accurately perform shop math and machining calculations. Follow written and verbal instructions, ensuring proper documentation and workflow continuity. Uphold all safety and 5S standards in the machine shop environment. Qualifications High School Diploma or equivalent (required). Minimum of 8 years of machining experience in a job shop or manufacturing environment. Experience with horizontal machining centers (preferred). Associate degree or technical certification in Machine Tool Technology (preferred). Can be relied upon to work regularly and on time, and maintain consistent attendance. Ability to work effectively and cooperatively with team members and other departments. Ability to manage multiple tasks and priorities in a fast-paced environment. Proficiency with computers and CNC programming software for communication, documentation, and data entry. Ability to lift up to 40 pounds safely. Ability to stand, bend, stretch, and perform physical tasks for the duration of a shift. Disclaimer: This job description has been designed to indicate the general nature and level of work performed by employees within this classification. It is not intended to contain or be interpreted as a comprehensive inventory of all duties, responsibilities, and qualifications required of employees assigned to this position. Additional Information We provide equal employment opportunities (EEO) to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, disability, veteran status or genetics. This policy applies to all terms and conditions of employment, including recruiting, hiring, placement, promotion, termination, layoff, recall, transfer, leaves of absence, compensation and training. If you have a difficulty applying for any job posted on Harsco Rail's website because a disability prevents you from using the online system, Harsco Rail offers the following alternate application procedure: Contact Matthew Fink, HR, at ************ and Harsco Rail will arrange for an alternate method of applying and will consider your application together with all other applications received for the job. Please call only for disability application. All your information will be kept confidential according to EEO guidelines.

Title: Machinist Hire Type: Direct Hire Benefits: Full medical, dental, vision, 401k Pay: $24/hour Schedule: 6:00 AM - 4:30 PM, M-FMUST HAVE: 3-5 years of related experience, proficiency in CNC and conventional machining We're seeking a skilled Machinist to perform complex, specialized work in the construction, repair, maintenance, and calibration of machine shop tools, dies, jigs, fixtures, and instruments. In this hands-on role, you will operate both conventional and CNC equipment to produce precision parts, perform machine setups, and ensure all components meet tight tolerances. The ideal candidate has advanced technical skills, strong problem-solving abilities, and a commitment to quality in a fast-paced manufacturing environment. Job Duties:Machining & Fabrication Operate conventional machine shop equipment (lathes, mills, grinders, vertical/horizontal saws) to produce and detail parts ranging from simple to highly complex within prescribed tolerances. Operate CNC vertical mills and lathes with Fanuc controllers. Perform precise machine setups, adjusting speeds, feeds, and depth of cut per blueprint, drawing, or engineering specifications. Inspect machined parts for conformance using precision measuring tools. Operate numerical control machines as required. Tooling Design & Support (as applicable) Design and construct tools, dies, jigs, and fixtures for manufacturing needs. Interpret tooling and fixture requests, create sketches, and fabricate solutions using various machines. Provide technical guidance and support to tool designers in developing new tooling solutions. Technical Expertise & Process Improvement Demonstrate advanced technical skills and mentor/train other employees as needed. Contribute to process improvements, applying new technologies when relevant. Maintain broad knowledge of manufacturing functions and ensure best practices in production areas. Qualifications: High School diploma, military technical training, or equivalent vocational education. 3-5 years of relevant experience in machining, toolmaking, or related manufacturing work. Strong understanding of manufacturing processes and ability to train others. Skilled in reading and interpreting complicated technical drawings and blueprints. Proficiency in mathematics, handbook formulas, and use of precision measuring instruments. Ability to interpret complex technical instructions in mathematical or diagram form and solve multi-variable problems. Decision-Making & Leadership: May make recommendations or decisions impacting team or departmental outcomes. Assist in setting goals/targets for the line or department. Potential to direct or guide other employees. Work Environment: Machine shop and production floor exposure, with potential contact with dust, gases, fumes, and chemicals. Required use of protective eyewear; moderate noise levels typical. Physical Demands: Occasional sitting, standing, walking, bending, and twisting. Frequent simple grasping; occasional power grasping, fine manipulation, and overhead reaching. Ability to lift/move up to 10 lbs occasionally. Reasonable accommodations available for individuals with disabilities.

Savannah River National Laboratory is seeking a Machinist to join a dynamic team in the Machine Shop of the Advanced Manufacturing & Design organization creating innovative solutions for the Savannah River Site, DOE complex and national security missions. The candidate will work in the Advanced Engineering R&D Machine Shop and perform work from work orders, drawings, design documents and procedures to perform machining activities based on skills and knowledge obtained from training and/or previous experience. Candidate should demonstrate necessary knowledge and skills to program, set up, and operate CNC equipment and CAD-CAM Systems, operate material handling equipment, and inspect and/or test parts and equipment to determine functional condition. Meet physical requirements for the essential duties, which include working around rotating equipment, being able to lift up to 50 pounds, prolonged standing, climbing, bending, and twisting. Minimum Qualifications: Associates Degree and 3-5 years of relevant experience. Major Duties/Responsibilities: Responsible for performing tasks from work orders, drawings, design documents and procedures to perform machining activities based on skills and knowledge obtained from training and/or previous experience. Responsible for obtaining guidance from supervision when the conditions warrant, but usually works under minimal supervision. Responsible for self-directed/peer decision type work environment to include planning sequence of manufacturing operations to achieve desired results. Responsible for attaining necessary knowledge and skills to program, set up, and operate CNC equipment and CAD-CAM Systems. Responsible for operating material handling equipment. Responsible for inspecting and/or testing parts and equipment to determine functional condition. Responsible for assisting supervision and/or management with understanding of problems and suggest possible solutions. Responsible for performing administrative functions such as timekeeping, data entry, and other administrative functions as needed to perform job. Ability to meet physical requirements for the essential duties, which include working around rotating equipment, being able to lift to 50 pounds, prolonged standing, climbing, bending, and twisting. Other duties as assigned by supervision.

The TFE Operator will be responsible for machine operation. This would include troubleshooting, documentation, and quality of material.

Job Type: Full-Time | Day Shift | In-Person Schedule: 40 hours per week | Monday-Friday, 8am-5pm with a 1-hour lunch break Pay: From $17.00 per hour Who we are: Sorinex Exercise Equipment, based in Lexington, SC, is a leader in fitness equipment manufacturing and innovation. For over 40 years, we've built the highest-quality gym and strength training equipment for home gyms, college athletics, professional sports teams, and the U.S. military. As we continue to grow, we're hiring motivated individuals to join our team. If you're looking for a career to grow and excel, apply now! Who we are looking for: We are seeking a reliable and motivated CNC Laser Operator to join our team and run our tube laser. Prior experience with a tube laser, CNC laser, or other machine operation is a plus. If you are interested in manufacturing, precision cutting, and working with industrial machinery, we encourage you to apply! We are looking for someone who can: Operate tube laser and CNC laser machines to perform precision cutting on metal components Select appropriate laser cutting programs based on job specifications and material type Set up, calibrate, and monitor laser equipment for optimal performance Perform routine maintenance and cleaning to ensure peak machine operation Inspect parts for quality, accuracy, and correct dimensions according to blueprints and drawings Load and unload raw materials and finished parts; organize for the next production stage Read and interpret blueprints, diagrams, engineering drawings, and bills of materials Follow standard operating procedures and maintain accurate production records Meet daily production goals while maintaining consistent, high-quality output Safely lift and move up to 50 pounds as required Work independently with minimal supervision, following written and verbal instructions Maintain a clean, safe, and organized work environment in compliance with safety standards Support other production tasks and departments as needed Perform additional duties as assigned Physical Demands: Lift, carry, push, and/or pull 1-50 lbs. frequently Squat/kneel, bend/stoop, crawl, twist/turn, grasp, and reach overhead and outward frequently Sit, stand, and walk for 1-10 hours per day Work in a fast-paced industrial environment wearing hearing protection, eye protection, steel-toed shoes, and other appropriate protective clothing Required Experience: CNC Laser Cutting: 1 year Machining: 1 year Benefits: 401(k) 401(k) Matching Dental Insurance Health Insurance Life insurance Paid time off Vision insurance

Job Description GENERAL SUMMARY: Coordinates activities of workers engaged in setting up and operating arc welding machine that seam-welds rolled plate to form large diameter spiral fabricated pipe by performing the following duties. MINIMUM QUALIFICATIONS: To perform the job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. ESSENTIAL FUNCTIONS/RESPONSIBILITIES: include the following: (Other duties may be assigned, including but not limited to cross training and housekeeping. Responsibilities also include attention to safety according to all safety rules.) In addition to the duties of cutoff, tracker and floor: In conjunction with department team leader, reviews daily work schedule and specification sheets for current material and process requirements; directs and assists crew members with setup for daily runs. Ensures mill machine is kept running by observing and correcting problems that arise. Monitors quality of alignment and weld process. Monitors and resolves employee issues; conducts and/or recommends employee discipline if required. Performs preventive maintenance and minor repairs to mill machinery and equipment. Refers electrical and hydraulic problems to maintenance department for resolution. Develops, recommends, and implements measures to improve production methods, equipment performance, and quality of product. Brings safety issues to the attention of department manager or safety manager. Loads coils onto the back of machine. Verifies that all positions have been checked and ready to start. Performs other tasks as instructed by supervision. PHYSICAL/ENVIRONMENTAL REQUIREMENTS: While performing the duties of this job, the employee is regularly required to stand, walk, use hands to finger, handle, or feel and talk or hear. The employee is frequently required to stoop, kneel, crouch, or crawl. The employee is occasionally required to sit, reach with hands and arms and climb or balance. The employee must regularly lift and/or move up to 10 pounds, frequently lift and/or move up to 25 pounds and occasionally lift and/or move up to 100 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision and ability to adjust focus. WORK ENVIRONMENT: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly exposed to moving mechanical parts. The employee is frequently exposed to fumes or airborne particles. The employee is occasionally exposed to extreme heat. The noise level in the work environment is usually loud.

INDEVCO North America (INA) is seeking a skilled and experienced Extrusion Operator specialized in Blown Film production to join our manufacturing team. The ideal candidate will be responsible for the efficient operation of extrusion machinery, ensuring the production of high-quality blown film products. The Extrusion Operator will play a crucial role in maintaining optimal machine performance, troubleshooting issues, and adhering to safety and quality standards. Key Responsibilities: Operate and monitor blown film extrusion machinery to produce quality film products according to production specifications. Set up, adjust, and control machine settings, such as temperatures, speeds, and thickness, to achieve desired product characteristics. Conduct routine equipment checks and preventative maintenance to ensure continuous and efficient operation. Monitor product quality throughout the production process, making necessary adjustments to maintain consistent quality standards. Conduct visual inspections and measurements of finished products to ensure they meet customer and company specifications. Troubleshoot and address any issues related to product defects or deviations from quality standards. Adhere to all safety protocols and guidelines to ensure a safe working environment. Operate machinery in compliance with company policies, industry regulations, and quality standards. Report any safety incidents, equipment malfunctions, or maintenance needs promptly. Maintain accurate production records, including machine settings, production rates, and quality control data. Complete required documentation and reports in a timely and accurate manner. Requirements High school diploma or equivalent. Additional technical or vocational training in extrusion operations is a plus. Proven experience as an Extrusion Operator, with a focus on blown film production. Familiarity with the operation and maintenance of blown film extrusion machinery. Ability to set up, operate, and troubleshoot blown film extrusion equipment. Basic understanding of mechanical and electrical systems related to extrusion machinery. Strong attention to detail and commitment to producing high-quality products. Knowledge of safety procedures and a commitment to maintaining a safe work environment. Effective communication skills, both verbal and written. Ability to work collaboratively in a team environment. Ability to lift and move heavy materials as needed. Comfortable working in a manufacturing environment with exposure to noise, dust, and varying temperatures. At INDEVCO, we provide our employees with a highly competitive benefits package, including life, medical, and dental insurance coverage, a 401(K)-matching plan, paid vacation, and an Employee Tuition Reimbursement benefit for professional certifications and degree programs. INDEVCO North America, Inc. is an equal opportunity employer. We embrace diversity and are dedicated to fostering an inclusive environment for all our employees.

Stanadyne is an independent supplier of diesel fuel injection systems to OEMs and the aftermarket. We don't just assemble parts. We solve complex thermal, mechanical, and hydraulic challenges, using robust experimental data and over 100 combined years of experience in materials engineering. This is an on-site position at our Blythewood, SC plant. Position Overview: Here is a glimpse of what you'll do: Analyzes complex machining needs; determines tools, equipment and materials needed, plans and carries out highly involved work projects. Manufactures high-quality precision details and parts on the tool room equipment. Works with all internal customers to develop fixtures and tooling and production methods. Completes set-ups on the tool room and prototype equipment. Ability to read and correctly interpret mechanical drawings, prints and GD&T. Maintain a clean and organized work area and conduct all work in a safe and efficient manner. Ability to effectively work in a team environment Experience working with AutoCAD and CAM software Stanadyne is an equal opportunity employer and does not discriminate on the basis of race, religion, national origin, sex, gender, color, marital status, sexual orientation, disability, veteran status or any other protected class.