Post job

Microwave technician vs calibration technician

The differences between microwave technicians and calibration technicians can be seen in a few details. Each job has different responsibilities and duties. It typically takes 6-12 months to become both a microwave technician and a calibration technician. Additionally, a microwave technician has an average salary of $47,493, which is higher than the $46,908 average annual salary of a calibration technician.

The top three skills for a microwave technician include test equipment, power meters and level troubleshooting. The most important skills for a calibration technician are metrology, customer service, and calibration procedures.

Microwave technician vs calibration technician overview

Microwave TechnicianCalibration Technician
Yearly salary$47,493$46,908
Hourly rate$22.83$22.55
Growth rate--
Number of jobs15,22548,741
Job satisfaction--
Most common degreeAssociate Degree, 48%Associate Degree, 48%
Average age5050
Years of experience1212

Microwave technician vs calibration technician salary

Microwave technicians and calibration technicians have different pay scales, as shown below.

Microwave TechnicianCalibration Technician
Average salary$47,493$46,908
Salary rangeBetween $37,000 And $60,000Between $35,000 And $62,000
Highest paying City-Santa Rosa, CA
Highest paying state-Hawaii
Best paying company-Boehringer Ingelheim
Best paying industry-Pharmaceutical

Differences between microwave technician and calibration technician education

There are a few differences between a microwave technician and a calibration technician in terms of educational background:

Microwave TechnicianCalibration Technician
Most common degreeAssociate Degree, 48%Associate Degree, 48%
Most common majorElectrical EngineeringElectrical Engineering
Most common collegeNortheastern UniversityNortheastern University

Microwave technician vs calibration technician demographics

Here are the differences between microwave technicians' and calibration technicians' demographics:

Microwave TechnicianCalibration Technician
Average age5050
Gender ratioMale, 95.6% Female, 4.4%Male, 87.7% Female, 12.3%
Race ratioBlack or African American, 6.3% Unknown, 4.3% Hispanic or Latino, 10.4% Asian, 8.0% White, 70.8% American Indian and Alaska Native, 0.1%Black or African American, 6.3% Unknown, 4.3% Hispanic or Latino, 10.4% Asian, 8.0% White, 70.8% American Indian and Alaska Native, 0.1%
LGBT Percentage8%8%

Differences between microwave technician and calibration technician duties and responsibilities

Microwave technician example responsibilities.

  • Assist in managing CDMA network, Voice/EVDO circuit's layouts, CDM circuit inventory and roll over's for cell sites.
  • Perform FCC proof of performance testing.
  • Measure insertion loss, isolation and VSWR.
  • Check quality of transmit signals and verify FCC compliance.
  • Conduct testing, tuning and troubleshooting of PC boards.
  • Maintain the operation of several active microwave and fiber systems by Nortel, Alcatel and Glenayre.
  • Show more

Calibration technician example responsibilities.

  • Comply with good laboratory practices FDA, QSR, ISO, safety and environmental regulations.
  • Calibrate and repair general-purpose and RF test, measurement, & diagnostic equipment (TMDE) and microwave passive standards.
  • Calibrate basic mechanical and electrical measurement instruments, such as calipers, micrometers and voltage-current-resistance meters.
  • Perform calibration and maintenance of measuring equipment including micrometers, calipers and drop indicators among others.
  • Maintain standards in accordance with cGMP, USP, JP and ISO.
  • Install MCC's, VFD's, motors, and Allen Bradley PLC's.
  • Show more

Microwave technician vs calibration technician skills

Common microwave technician skills
  • Test Equipment, 20%
  • Power Meters, 11%
  • Level Troubleshooting, 10%
  • MW, 7%
  • Frequency Counters, 5%
  • Antenna Systems, 4%
Common calibration technician skills
  • Metrology, 10%
  • Customer Service, 10%
  • Calibration Procedures, 6%
  • Troubleshoot, 6%
  • Hand Tools, 4%
  • Equipment Calibration, 4%

Browse architecture and engineering jobs