Oglethorpe Power jobs in Rome, GA - 754 jobs

Job Description The Hydro Plant Electrician is responsible for the lead in performing checkout, troubleshooting, installation, modification, and repair of electrical equipment/controls associated with the following power generating plants: pumped storage and conventional hydroelectric plants and simple cycle gas turbine plants. Performing preventive and predictive maintenance on plant electrical equipment that includes Baker surge testing, partial discharge data collection, thermographic and airborne ultrasonic inspections, high voltage and current testing, TTR testing, and Ductor testing. Responsible for generating electric power in compliance with corporate safety policies, mandatory electric reliability standards, and regulations from FERC, EPA, EPD, OSHA, DOT, and other pertinent governmental authorities. Job Duties: Takes the lead in performing check-outs, maintenance, and troubleshooting of electrical equipment such as, but is not limited to, protective relays, over-current devices, meters and transducers, electrical switchgear and circuit breakers, electric motors and motor controls, generators and excitation equipment, batteries, and power inversion and conversion equipment. Maintain work area and equipment in a clean and orderly manner. Observe corporate and plant(s) safety rules and practices. Engage in operations for alteration, installation, or replacement of station electrical components by working with blueprints, electrical schematics, logic diagrams, plans, or sketches. Make necessary changes, remove old components, install new components, and field check the system, as assigned. Perform a variety of duties such as equipment inspection to determine extent of defects, diagnosis of faulty operations and apply corrective methods. Engage in operational tests, lubricate equipment, verify working clearances, and check completed work. Perform preventive and predictive maintenance testing and servicing of components and equipment. While performing these duties, the incumbent may be required to carry up to 75 pounds of tools, equipment, and/or materials. The position may necessitate working within confined spaces and other areas that are typically difficult to access while performing these duties. To access the work locations, the incumbent must be capable of climbing up and down several hundred steps, climb scaffolding, work at heights, within confined spaces, near or over water, near high voltage equipment, and must be able to wear, and use required personnel protective equipment, including self-contained breathing apparatus, full face cartridge respirators, and air lined supply respirators. Operate all electrical shop equipment, basic machine shop tools (saws, drill presses, grinders, and hydraulic presses) and have basic welding skills using SMAW, GMAW, and FCAW welding processes to perform, non-structural welds involving reconditioning of parts or fabricating new parts from drawings or plans. Sets up machines for desired operation and performs work within specified tolerances and standards. This work involves exposure to high voltage, welding arcs, and heat/flame. The incumbent must be able to wear and use the required protective equipment. Balance and align plant equipment in the plants owned and/or operated by Plant Operations. During the execution of these tasks, the individual will encounter rotating machinery and may be exposed to high voltage. The incumbent must be able to wear and use the required protective equipment. Maintain job related qualifications and system knowledge of the electrical equipment at the plants serviced. This to be done by attending and participating in scheduled training and safety meetings and acquiring and maintaining skill levels and certifications to complete job tasks. Perform preliminary design of modifications to mechanical systems, which are reviewed for accuracy and for additional support requirements by the Maintenance Manager and/or Senior Electrical Generation Engineer. Required Qualifications: Education: High School Graduate-General Studies Experience: Five (5) years of progressively responsible electrician experience in a hydroelectric and/or gas turbine electric power generating plant is required. Equivalent Experience: Eight (8) years of progressively responsible electrician experience in an industrial plant is equivalent. Two (2) years of college or technical training in a related technology program are equivalent to two (2) years of experience. Completion of the Rocky Mountain Hydroelectric Plant Maintenance Training Program for a Maintenance Electrician as outlined in Maintenance Training Procedure RMP MD-A002 is equivalent to five (5) years of experience. Job Posted by ApplicantPro

We Are Hiring Local CDL Class A Drivers! College Park, GA Established in 1978, United Scrap Metal has grown from $200 and a rental truck to one of the largest full-service recyclers in the country. United Scrap Metal offers recycling solutions guided by decades of experience and a firm commitment to doing the right thing. We are passionate about making a positive difference for our customers, consumers, and communities. Overview: The Driver s main role is to pick up, transport and deliver freight in a safe and efficient manner. This individual will report to the Transportation Manager. Drivers are also supervised and lead by the Dispatchers. Pay and Benefits: $24 - $26 per hour + time and a half after 40 hours Health, Dental, and Life Insurance Paid vacations and paid time off 2 yearly bonuses Monthly Bonus Plan hours a week Mon Fri with weekends off! Requirements: At least 2 years of similar industry experience preferred, ideally in a similar role / industry / fast paced environment. Must have a current Class A driver s license. Experience in the recycling industry, ability to identify metal materials, as well as van, flatbed, gondola, and roll-off experience a plus. Candidate must pass a pre-employment physical, background and credit check and pass all DOT standards, including but not limited to a driving record check. The Company desires a candidate who has shown a stable job history, dependable attendance practices and whose references can state is a trustworthy individual. Notices and Disclaimers Reservation of Rights: This is not, nor is it intended to be an exhaustive list of all job tasks that the team member may be required to perform, and the team member may be required to perform additional functions. United Scrap Metal reserves the right to revise this at any time in its sole discretion. Equal Employment Opportunity. United Scrap Metal ( USM ) is an equal opportunity employer and is committed to equal employment and advancement opportunity based on merit for all qualified individuals without discrimination because of race, color, national origin, ancestry, sex, age, religion, marital status, physical or mental disability or genetic information unrelated to ability to perform the job, pregnancy, child birth or related medical condition, sexual preference or gender identity, military service status or status as a disabled veteran or Vietnam era veteran, or for any other reason prohibited by law. Requesting an Accommodation. If you are a qualified individual with a disability or a disabled veteran, you may request a reasonable accommodation if you are unable or limited in your ability to access job openings or apply for a job on this site as a result of your disability. You can request reasonable accommodations by contacting People Development (Human Resources) at . Employment at Will. Employees ( Team Members ) are not hired for any definite term or duration. Team Members are employed at will. This job description is not intended to create a contract binding United Scrap Metal or Team Member to an agreement of employment for a specific term. This means that either the Team Member or United Scrap Metal is free to end the employment relationship at any time, for any reason, with or without cause and with or without notice. Apply below or call today!

Title: CAD Manager Reports to: Design Management Department Manager Status: Full-time Working Hours: 8am - 5pm Working Location: Rockmart, Georgia / Remote / Hybrid Work alongside a team of designers, drafters, and engineers to create and control mechanical designs for boilers and similar industrial steam equipment to spear-head the company wide integration of 3D models. Utilize 2D and 3D CAD software plus advanced tools and features such as PDM, configurations, and rendering tools. Apply knowledge of machine design and manufacturing processes to ensure products are properly designed and suitable for manufacturing. Manage documentation on drawings and within the ERP system. Participate in the formal engineering change order process to evaluate and implement design changes. Act as a representative of product designs providing support to other departments by interpreting designs, creating customer-specific drawings, resolving BOM issues, and similar. The focus of this role will evolve over time. Following successful migration from 2D to 3D designs, this position will have the opportunity to contribute more directly to design, engineering, and product development projects. Essential Duties and Responsibilities: Create 3D models in Solidworks PDM from 2D drawings, ensuring accuracy and alignment with original designs. Organized long term project tracking and documentation with the ability to stay on track without supervision. Maintain and update product documentation, including Bills of Materials (BOMs), manuals, and installation instructions, ensuring they are accurate and up-to-date. Communicate clearly and collaborate with other team members and departments to ensure designs meet all applicable requirements. Support the review, evaluation, and execution of Engineering Change Requests (ECRs) in a timely and efficient manner including participation in drawing checking procedures. Support the creation of drawings and models for custom product designs, as requested by customers, sales team members, and other engineers. Apply your knowledge and experience to ensure that products are designed correctly and are suitable for manufacturing. Create and maintain engineering design standards and best practices as it pertains to 3D modeling. Position Requirements (knowledge, skills and abilities required to perform satisfactorily in the position): Bachelor's degree in engineering 3+ years of experience designing and drafting industrial products with exposure to steel construction, piping and ducting, combustion systems, fans and pumps, and electrical components 2+ years of experience with product lifecycle management of industrial products including BOM management and ECO functions within PDM and ERP systems Expert working knowledge of CAD design and drafting standards and software such as SolidWorks and AutoCAD Physical Demands: Position requires sitting working at a keyboard over 2/3 of time. Position requires standing under 1/3 of time. Position requires walking under 1/3 of time. Position requires reaching, stooping, kneeling, crouching, and/or crawling under 1/3 of time. Position requires climbing and balancing under 1/3 of time. Position requires talking 1/3 to 2/3 of time. Position requires climbing stairs under 1/3 of time. Position requires hearing over 2/3 of time. Position requires using close, distance, and color vision over 2/3 of time. Position requires reading and interpreting instructions over 2/3 of time. Position requires regular and reliable attendance.

We Are Hiring Local CDL Class A Drivers! College Park, GA Established in 1978, United Scrap Metal has grown from $200 and a rental truck to one of the largest full-service recyclers in the country. United Scrap Metal offers recycling solutions guided by decades of experience and a firm commitment to doing the right thing. We are passionate about making a positive difference for our customers, consumers, and communities. Overview: The Driver s main role is to pick up, transport and deliver freight in a safe and efficient manner. This individual will report to the Transportation Manager. Drivers are also supervised and lead by the Dispatchers. Pay and Benefits: $24 - $26 per hour + time and a half after 40 hours Health, Dental, and Life Insurance Paid vacations and paid time off 2 yearly bonuses Monthly Bonus Plan hours a week Mon Fri with weekends off! Requirements: At least 2 years of similar industry experience preferred, ideally in a similar role / industry / fast paced environment. Must have a current Class A driver s license. Experience in the recycling industry, ability to identify metal materials, as well as van, flatbed, gondola, and roll-off experience a plus. Candidate must pass a pre-employment physical, background and credit check and pass all DOT standards, including but not limited to a driving record check. The Company desires a candidate who has shown a stable job history, dependable attendance practices and whose references can state is a trustworthy individual. Notices and Disclaimers Reservation of Rights: This is not, nor is it intended to be an exhaustive list of all job tasks that the team member may be required to perform, and the team member may be required to perform additional functions. United Scrap Metal reserves the right to revise this at any time in its sole discretion. Equal Employment Opportunity. United Scrap Metal ( USM ) is an equal opportunity employer and is committed to equal employment and advancement opportunity based on merit for all qualified individuals without discrimination because of race, color, national origin, ancestry, sex, age, religion, marital status, physical or mental disability or genetic information unrelated to ability to perform the job, pregnancy, child birth or related medical condition, sexual preference or gender identity, military service status or status as a disabled veteran or Vietnam era veteran, or for any other reason prohibited by law. Requesting an Accommodation. If you are a qualified individual with a disability or a disabled veteran, you may request a reasonable accommodation if you are unable or limited in your ability to access job openings or apply for a job on this site as a result of your disability. You can request reasonable accommodations by contacting People Development (Human Resources) at . Employment at Will. Employees ( Team Members ) are not hired for any definite term or duration. Team Members are employed at will. This job description is not intended to create a contract binding United Scrap Metal or Team Member to an agreement of employment for a specific term. This means that either the Team Member or United Scrap Metal is free to end the employment relationship at any time, for any reason, with or without cause and with or without notice. Apply below or call today!

A leading advisory firm in Atlanta is seeking a part-time Tax Advisory professional. Responsibilities include assisting clients in location assessments, developing financial models, and presenting analyses. The ideal candidate should have over 10 years of relevant experience, strong analytical and interpersonal skills, and proficiency in Microsoft Office. Fluency in Japanese is preferred, and the role includes flexibility for travel and a focus on both domestic and international incentives. #J-18808-Ljbffr

MXI Partners are currently recruiting for Data Center Project Managers for a fast-growing data center construction and infrastructure organization. You'll lead delivery of network infrastructure, cabling and technical projects within mission-critical environments, ensuring work is completed safely, on time, and within budget. What's on offer: Salary up to $175,000 + bonus + benefits Opportunity to join a market-leading Data Center contractor, directly supporting AI-era facility construction Fast-career growth and professional development Key Responsibilities: Lead project planning, execution and delivery on site. Develop and maintain project schedules and key milestones. Manage costs, proposals, client communications and project reporting. Coordinate with internal teams, subcontractors, and stakeholders. Proactively identify risks and resolve project challenges. Minimum Qualifications: 5+ years' experience in construction, focused on Project Management, Construction Management or equivalent disciplines Experience leading data center focused projects, ideally low-voltage (structured cabling, BMS/EPMS, power distribution/PDU) Proven delivery of mission-critical projects to schedule and budget with a focus on quality and safety. Strong track record of mentoring and growing teams of technicians, engineers and junior PMs

Job Description Join Oglethorpe Power as a Combustion Turbine Technician III-IV at our Sewell Creek Plant, where you will serve as a senior technical resource supporting the safe, reliable, and efficient operation of a critical generation facility. In this advanced role, you will lead and execute complex maintenance, troubleshooting, inspections, and operational activities for combustion turbines and balance-of-plant systems, ensuring high equipment reliability and readiness to meet system demands. Technicians at Sewell Creek operate in a fast-paced environment that requires strong technical judgment, adherence to rigorous safety and compliance standards, and the ability to mentor junior technicians while coordinating closely with plant leadership and support teams. This position offers experienced turbine professionals the opportunity to take ownership of plant performance, contribute to continuous improvement initiatives, and play a key role in supporting grid reliability across Oglethorpe Power's generation fleet. Responsible for the performance, operations, and maintenance of simple-cycle combustion turbine technologies and generating assets in a manner that optimizes reliability, availability, and O&M costs while maintaining the highest standards in safety, environmental, and NERC electrical reliability. A technician must understand and apply concepts to operate the equipment and perform plant systems analysis to take actions for identifying, resolving, and/or avoiding failure modes. In addition, the individual performs operator rounds, troubleshooting, preventive, corrective, and predictive maintenance on plant systems/equipment to ensure safe, efficient, and reliable plant operations, as well as enhance equipment longevity. The incumbent is responsible for continuous improvement and providing reliable and efficient electric power generation in compliance with corporate safety policies and procedures, environmental, mandatory electric reliability standards, FERC, EPA, EPD, OSHA, DOT, and all applicable governmental regulations. Job Duties: Daily activities include start-up and shutdown of the plant equipment, operator rounds, overseeing plant physical security, clearances, receiving materials/inventory, maintaining 3-part communications with GSOC, shift log communications, and issuing applicable Operational Advisory and Event Reports. Documenting and communicating operational or maintenance conditions and activities to allow the efficient and orderly transfer of information to others. Responsible for assigned work orders and systems ownership. Compliance with the Conduct of Maintenance Program, engaging in the 4-week and outage planning and preparations, including reviewing, updating, or developing Job Plans, ordering parts, and updating inventory requirements. Take appropriate corrective actions to address abnormal conditions, engage the supervisor, and other resources, and utilize MAXIMO work order/management processes. Complete required reporting, documentation, change management control, and VAULT drawing updates. Maintain individual safe work practices while performing duties, including completing required training, understanding, and following the OPC Safety Manual/Procedures. Perform the function of Clearance Authority for establishing and maintaining safe isolation of equipment/device for the protection of all personnel performing work within established boundaries. In addition, participate in monthly safety meetings and complete all required training to ensure personal compliance, safe work practices, operational excellence, and technical knowledge. Responsible for the administration of contracts as assigned and the coordination of contract support services as required. This project/contract management may include capital project scoping document preparation, budget management, contractor oversight, status reports, and administrative duties as required. Compliance Reporting, responsible for the preparation of required documentation and reports to the Corporation's local, division, and senior management, owners, regulatory authorities, and other agencies to assure compliance with regulations and the terms of the Management Services Agreement. Maintains job-related qualifications, system knowledge, and understanding of OPC policies and procedures (Emergency Action Plan, Environmental Baseline Book, SERC Plant Level Procedures, etc.). Required Qualifications: Education: High School Diploma or equivalent required. Associate's degree in engineering, engineering, or related physical science, or equivalent preferred. Experience: 4+ years of experience in operation or maintenance of an operating commercial power production facility, a large natural gas facility, or combustion turbine-driven naval vessel. An advanced analytical and technical problem-solving background is preferred. Equivalent Experience: Two (2) year or greater technical degree or equivalent, and three (3) years' experience in operating or maintaining a thermal electric power station, equivalent military, or similar industry. In addition, an advanced analytical and technical problem-solving background. Consideration of equivalent experience will be determined based on a combination of education, training, and professional, technical, or military experience which provides the requisite knowledge, skills, and abilities for this job. Education considered may include technical and college studies and degrees, industrial training programs and certifications, and military training. Experience considered may include related industrial and military work. Specialized Skills: A strong ability to work in a team environment. An effective trainer of personnel and one who motivates others to succeed. The ability to extract, comprehend, and develop instructions from technical manuals, journals, drawings, technical literature, and other job-related material. The ability to effectively communicate orally and in writing using the English language. The ability to effectively use control systems (such as Siemens T3000, GE Mark VNI, Allen Bradley PLCs, etc.) and computer applications (such as Outlook Email, MS Office Suite, IBM-Maximo, and Vault). Possess independent decision-making capabilities in stressful situations with minimum supervision. The ability to troubleshoot electrical, instrument, and mechanical systems for malfunctions. The ability to work on and around high-voltage electrical equipment. The ability to instruct others in the performance of testing, checkout and troubleshooting of equipment. The ability to provide technical direction and leadership to Assistant Combustion Turbine Technicians and contractors brought in to augment the workforce in the performance of modifications and major repairs to equipment. The ability to perform predictive maintenance and interpret data on plant equipment performance. The ability to perform basic management and supervisory skills when needed. Licenses, Registrations, and/or Certifications: Valid driver's license which meets the insurance eligibility requirements under Oglethorpe Power's qualification program. Travel: 15% Unusual hours or overtime: Will require scheduled and call-out overtime as plant operating and maintenance needs dictate. Production schedules require 24-hour coverage, rotating shift schedules. Job Posted by ApplicantPro

Fall, 2026 Co-op NEEDED Students must be a part of the school's Co-op/Intern Program with a 2.7 GPA and can work 40 hours a week for 14 weeks in the Spring. This is not a remote position. Please submit an Unofficial Transcript along with a Resume when applying. Relay & Control Design Perform routine system protection functions: Develop Preliminary Design Single Line (PDSL) drawings for substation facilities; Provide Electric Membership Cooperatives (EMCs) with fault Data Sheets at the distribution service point; Make field changes for As-Built drawings; Assist staff engineers with the management of technical databases spreadsheets, and files. Work under the guidance of staff engineers, receive specific instructions, and use limited judgment in carrying out work assignments. Basic Electrical theory, Proficient with Word, Excel, PowerPoint, Access. Experience in AutoCAD drafting desired. Strong interest in Power Systems. Desired Major(s): Electrical Engineers

Are you looking for a company who believes in world class employee culture and focuses on growing YOU professionally? Alpine Intel is dedicated to innovation across the property, auto, liability, and workers comp insurance fields - helping our customers reach peak performance throughout the policy life cycle. Through our operating brands, HVACi, StrikeCheck, National Fire Experts, Donan Engineering, BSC Forensics, Component Testing Laboratories, The Robison Group, VRC Investigations, TechLoss, Mecanica Scientific Services, and HMI we are respected as the industry leader for our scale and our track record of conducting expert, specialized, and accurate investigations. Headquartered in Charlotte, North Carolina, our team of experienced professionals provides high-quality solutions nationwide. Alpine Intel is looking for bright candidates with a passion for problem solving to join our growing team. Welcome to Alpine Intel, a leader in the property insurance intelligence industry. We are currently seeking a Part Time Private Investigator - Special Investigations (SIU) to join our growing team in Savannah, GA. Candidates with at least five (5) years of investigations experience are strongly encouraged to apply. Qualified candidates are interested in utilizing their investigative skills to conduct a variety of investigations on insurance related matters; such as auto and property theft, fire damages, auto accidents, commercial claims, finding missing persons, courthouse searches, and other investigative tasks. As an SIU Investigator, you will be joining an incredible team of investigators and industry leaders. We are looking for people who are enthusiastic about investigations, those who thrive in a diverse work environment, and individuals who have a commitment to the very highest standards of honesty, integrity, and respect. Key Responsibilities Include: Complete recorded detailed interviews of those insured, claimants, witnesses, and others as identified. Complete scene investigations, including photographing. Conduct in-person visit of medical clinics. Complete neighborhood canvasses. Make sound judgments during the course of the investigation. Provide timely progress updates. Complete detailed investigative reports. Minimum Qualifications: MUST have current and active Private Investigation License to be eligible for hire. Self-motivated, determined, and intuitive with a strong initiative and work-ethic. Ability to identify critical issues quickly and accurately. Demonstrate observational, organizational, and listening skills. Excellent oral and written communication. Ability to work independently, as well as in a team. Flexible schedule working weekends, holidays, and possible evenings. Candidate must own a reliable computer, preferably a laptop, with access to high-speed internet and a scanner or fax machine. Must have strong computer and internet skills. Proficient with a digital camera. Must possess a valid driving license and own your reliable vehicle. Applicants must pass an extensive background check. Must be able to pass a drug test with negative results (except when undergoing documented medical treatment). College Degree preferred. To learn more about us visit ************************ Alpine Intel is committed to creating a diverse environment and is proud to be an equal opportunity employer. We are an E-Verify participating employer.

Job Description Why Join Our Team? Do you want to be part of a team that is making a positive difference in lives all across the globe? Do you want to be part of a culture where you are recognized, respected, and rewarded for a job well done? U.S. Pipe has been providing quality water and wastewater products since 1899, and for the past 120 years we have proudly supported local governments, municipalities, water departments, and businesses all across the United States, and the world. What We Offer: Team Collaboration: Join a team-oriented environment where collaboration is not just a buzzword but a priority. Career Growth: Be part of an industry leader renowned for world-class design, manufacturing, sourcing, and distribution, and take your career to the next level. Comprehensive Benefits: We provide a comprehensive benefits package with options tailored to meet your needs and those of your family. About the Role: U.S. Pipe is seeking a Technical Resource Engineer to join our team. This position responsibilities will include consults with owners, owner's representatives (consulting engineers), and customers regarding technical matters concerning product application, construction specifications, installation procedures, customer complaints, and other services required to promote the company's products and maintain the end user's satisfaction. THIS CANDIDATE MUST BE RELOCATEABLE TO THE RICHMOND, VIRGINIA AREA. Specific Responsibilities: Drives specification inclusion and product promotion through presentations to engineers, municipalities, contractors, and owners. Supports the sales staff. Performs field investigations on an as needed basis of customer complaints when the company's product fails to meet the customer's expectations making recommendations as to remedial action required to resolve the source of the dissatisfaction. Recommendations are also made concerning financial settlements on customer damage claims. Consults with owners and owner's representatives concerning the proper application of the company products and assists in drafting project specifications incorporating ANSI, AWWA, ISO and other applicable standards. Assists in design of product systems to meet specific project needs incorporating ANSI, AWWA, DIPRA, ISO, and other applicable design procedures. This consultation may involve corrosion affects and prevention of the company's products. Consults with customers (including distributors, contractors, and owner's personnel) on proper application, assembly, and installation of the company's products. Trains installation personnel in the proper assembly and installation techniques. Meets with owner's personnel to discuss failures of the company's products to meet performance expectations and participates in mutual resolutions to achieve the owner's expectations. Consults with various company department heads and advises on service and product shortcomings effecting remedial action as required. Qualifications: Requires a BS in Engineering (Civil/Mechanical preferred). Engineer in Training (EIT) certificate preferred, and a Professional Engineer (PE) license preferred (or ability to obtain). Waterworks or Public Utilities experience. Possess problem solving skills Requires good verbal, written and presentation skills. Must have the ability to apply standard engineering principles to situations and be able to develop solutions incorporating available products and procedures to minimize customer work stoppage in an economical manner. Must have a general knowledge of construction equipment and its capabilities, and construction practices and procedures. Must be able to communicate and negotiate with disappointed people under less than amicable conditions. Every employee is expected to demonstrate the following core values: customer commitment, high-performance culture, fleet of foot, innovation, accountability, integrity, respect for others and teamwork. Scope Data/Working Conditions/Physical Demands: The employee will be working “on-road” 25%-50% business travel, heavy at times. It will require business travel to the various pipe plants and job sites, thus exposing the employee to Foundry operations and heavy construction. The employee will be exposed to the following working conditions: Extreme heat, cold, and noise. The employee will be required to perform the following actions (from time to time): Standing, Walking, Balancing, Stooping, Kneeling, and Reaching.

We are looking for a reliable and safety-minded Heavy Equipment Operator to join our team. You will be responsible for operating machinery such as the Sennebogen 835m or Doosan 300 LC excavator, equipped with a hydraulic grapple or magnetic crane. Your role will focus on safely and efficiently sorting, loading, unloading, and moving scrap metal and debris within the work area. This position requires working outdoors in various weather conditions, and strict adherence to SA Recycling's health, safety, and environmental standards is mandatory SA Recycling offers: * Competitive Pay * Comprehensive benefits including affordable medical options, dental and vision care * 401k with a Company Match * Weekly Pay * Referral Incentives * Company provided uniforms and PPE Responsibilities of a Material Handler * Basic sorting of scrap, as well as metal and debris in preparation for processing. * Provide a safe environment for all employees, customers, and visitors. * Operate heavy machines to lift, sort, load or unload scrap metal and debris in preparation for processing. * Perform daily inspections on equipment reporting any defects or needed repairs to supervisor. * Determine load weights and verify against lifting capacities to prevent overloads and dangerous situations. * Comply with all applicable federal, state, local, & SA Recycling safety, health, & environmental rules, regulations, policies, & procedures. Qualifications of a Material Handler * High School diploma, GED Certification, or equivalent work experience. * Must pass a required Background, Drug screen and pre employment physical. * Experience in the operation of a Caterpillar, excavator Sennebogen, Grapple. * Previous Hydraulic Crane experience preferred. * Bi-lingual (English and Spanish) a plus. * Ability to carry out instructions provided in written, oral, or diagrammatic form. * Ability to learn new tasks as assigned required. PLEASE NOTE: The above statements are intended to describe the general nature and level of work being performed by people assigned to this job. They are not intended to be an exhaustive list of all responsibilities, duties and skills required. An offer of employment by SA Recycling is contingent on the satisfactory completion of a post-offer drug screen, physical exam, and background check with a credit check (if position specified). All US applicants must be 18 years of age or older.

Greystone is a private national commercial real estate finance company with an established reputation as a leader in multifamily and healthcare finance, with over $12 billion in loan originations in 2024. The firm consistently ranks in the Top 10 for Fannie Mae & Freddie Mac multifamily loan originations and is the #1 Overall HUD Multifamily and Healthcare Lender in the country. Greystone also ranks nationally as a top affordable housing, seniors housing, and small balance loan lender. At Greystone, charity is at the heart of who we are and what we do. At Greystone, everything we do is driven by our purpose of improving others' lives. As we work hard to maintain our ranking as a top national commercial real estate lender, our culture of caring and support is just as important. We don't just say “Where People Matter” - we lead with this mantra every day to guide our actions and behaviors. Greystone is committed to fostering and preserving a culture of inclusion. Belonging is at the heart of our culture of caring, integrity and excellence and is a driving force behind our entrepreneurial spirit and creativity.   We are seeking a Property Inspector to join our Agency Lending team. The Property Inspector will coordinate and perform property inspections and provide support to our underwriting teams, Fannie Mae, Freddie Mac, and HUD by reviewing third-party reports. The Property Inspector will also advise underwriting and complete lease audits, rent roll analysis, and other work as assigned. Primary Duties and Responsibilities: Coordinate with senior underwriting leadership to create a system that provides a logistical approach to managing property inspections across all Agency products and markets. Calibrate with internal underwriting, the Third Party Administration team, and Agency partners to ensure compliance with applicable guidelines. Coordinate the site inspection with owner representatives and Agency representatives. Review third-party reports and coordinate with underwriting for report revisions and final reports. Complete lease audits, rent roll analysis, etc. Experience, Skills, and Abilities Required: 3-5 years of experience in commercial real estate property inspections. Bachelor's Degree. Excellent communication, decision-making, and feedback skills. Ability to effectively interact with all levels of internal and external business partners. Advanced analytical and problem-solving skills. Ability to manage multiple deadlines and prioritize work. Experience with Microsoft Office Suite (Excel, Word, PowerPoint, Outlook). Direct experience with Capital Needs Assessments (CNA), Phase 1 Environmental Site Assessments (ESA), and appraisals is preferred but not required. Travel will be required to perform site inspections nationwide, up to 75% of the time. At Greystone, we believe that finding creative solutions for our clients comes from the collaboration of people with diverse backgrounds and perspectives. We strive to build a work environment that empowers all individuals with opportunities to channel their entrepreneurial spirit. Greystone is an EEO employer. *The firm is the #1* overall HUD multifamily and healthcare lender by firm commitments, and a top 10 Fannie Mae and Freddie Mac multifamily real estate lender.* *For HUD's 2025 fiscal year ending September 30, 2025. Based upon combined firm commitments received by Greystone Funding Company LLC and Greystone Servicing company LLC and excludes risk sharing and hospital loans.

Bermex, Inc.Full time RegularAbout The Team At Bermex, we put value on our customer relationships. We're always looking for a way that we can delight our customers by going the extra mile. Bermex offers expert meter reading services and solutions to utilities and associated organizations throughout the United States, including leak detection, atmospheric corrosion, line location, software service solutions, as well as water, gas, and electric meter reading. At Bermex, we are always looking for motivated individuals who enjoy working independently and love the outdoors to become a part of our team. About the Role The Meter Reader reports to the Meter Services Supervisor at Bermex. This position plays a key role in reading and inspecting gas, electric, and/or water meters. This position also requires a high degree of walking in outdoor environmental conditions, excellent time management, and exceptional flexibility day to day. Great Pay & Bonus Potential: Earn $17.00 per hour with the chance to boost your pay through the Bermex Productivity Incentive Plan (BPIP). You'll receive extra pay for production over set goals, giving you more earning power for your hard work! What You'll Do Meter Reading: Read meters on a daily and/or special basis, typically on a customer's premises for service bills Carry out assigned duties in the required time frame for cycle readings, assign sequence numbers to new services, and rearrange meter reading routes as necessary. Inspect meters and report damage or apparent malfunctions to assigned supervisor Evaluate unsafe conditions or clean out meter boxes Use electric, gas, water meter reading devices Use hand tools such as a screwdriver, pliers, flashlights, keys, gas detectors, generators, pumps, hand pumps, shovels, lid handles, etc. Use printed materials such as service orders, maps, manuals, and computer printouts Assist with training of new meter readers Read Meters in Various Environmental Conditions: Extensively walk and stand for much of the workday Walk for long distances (occasionally up to 20 miles per day) in various weather conditions (rain, sleet, hail, snow, extreme heat or cold, etc.) Exert physical force moving objects (routinely 10lbs of force, up to an occasional 50lbs of force) Customer Communication: Refer all consumer complaints to the appropriate authorities Provide general information about the meter services to customers, when applicable Use telephones, tablets, and/or computers to communicate Other duties as assigned. About You Must haves: Education: Some high school education, must be 18 years of age or older Experience: No experience necessary, employees will be trained. Must possess a valid driver's license Nice to haves: Education: High School Diploma or GED Experience: At least 1 year of experience in meter reading or working in outdoor conditions Your Skills: Ability to multi-task, and work independently and as a team Exceptional flexibility in daily routines and route scheduling Adequate time management skills to finish daily meter reads in a timely manner, figuring out an efficient way to read meters for that day Excellent communication skills, comfortable interacting with management and customers Ability to interact with unhappy or negative customers in a professional manner Excellent attention to detail for problem solving and finding Ability to walk long distances and prepare for weather conditions, accordingly This role would not be a good fit if you: Do not enjoy working independently Do not enjoy working in outdoor conditions Do not enjoy walking long distances Are not flexible and do not enjoy adapting to your current work schedule or routine Do not have adequate planning and time management skills to finish a days work in a timely manner Drug/Alcohol Testing: Drug/alcohol testing is required Drug/alcohol testing required per Non-Regulatory requirements for employees working with water, electric, and meters Drug/alcohol testing required per Federal DOT regulations for employees working with gas meters Benefits Health and Safety: Group health plans including medical/prescription, dental, vision and a variety of other coverage options Company paid group life insurance, accidental death & dismemberment insurance, short and long term disability Flexible Spending Accounts or an option for a Health Saving Account with company match Company paid Employee Assistance Program (EAP) for all employees and eligible family members Retirement: Automatic enrollment in the Employee Stock Ownership Plan (ESOP) at no cost Roth or Traditional 401(k) Retirement plan with company match PTO Plans (after 90 completed days of service for full-time employees): Paid Vacation Paid Holidays Paid Wedding Day Veterans Day paid time off for our veterans Paid Sick Time (New York based positions ONLY) Perks/Allowances: Company vehicle (for all driver-based positions) Gas card for company vehicle (if applicable) Company provided cell phone or mobile allowance (if applicable) Boot allowance from approved vendors Daily per diem for travel-based positions Where We Work Employees will begin their day at the local office where they will pick up their company vehicle, equipment, and assignments for the day. We are an Equal Employment/Affirmative Action employer. We do not discriminate in hiring on the basis of sex, gender identity, sexual orientation, race, color, religious creed, national origin, physical or mental disability, protected Veteran status, or any other characteristic protected by federal, state, or local law. If you need a reasonable accommodation for any part of the employment process, please contact us by email at ************** and let us know the nature of your request and your contact information. Requests for accommodation will be considered on a case-by-case basis. Please note that only inquiries concerning a request for reasonable accommodation will be responded to from this e-mail address. The contractor will not discharge or in any other manner discriminate against employees or applicants because they have inquired about, discussed, or disclosed their own pay or the pay of another employee or applicant. However, employees who have access to the compensation information of other employees or applicants as a part of their essential job functions cannot disclose the pay of other employees or applicants to individuals who do not otherwise have access to compensation information, unless the disclosure is (a) in response to a formal complaint or charge, (b) in furtherance of an investigation, proceeding, hearing, or action, including an investigation conducted by the employer, or (c) consistent with the contractor's legal duty to furnish information. 41 CFR 60-1.35(c) Company: ACRT, Inc.

Who We Are Nexus Water Group is a leading regulated water and wastewater utility serving more than 1.3 million people across 20 U.S. states and 2 Canadian provinces. "Nexus" means connection. Through the essential water and wastewater services we deliver, we have a very personal connection to the people, businesses, and communities we serve. This is why our operations are locally led and managed. Every day, over 1,300 professionals deliver vital, safe, and reliable service through over 670 water systems and 360 wastewater systems. What We Offer * Paid Time Off and Holidays: Starting at 3 weeks annually and paid company holidays * Comprehensive Benefits: The first day of the month after your start, you'll have access to your health, dental, prescription and vision benefits to help you stay well. Other great benefits include company provided life insurance and Employee Assistance Program just to name a few. * 401(k) Program: Employer contribution. Employer contribution made to the 401(k) plan are vested at 100% and start 30 days after your start. * Grow with us: Professionally development opportunities through training, professional certifications, and education allowance * Employee Resource Groups (ERG): ERGs are voluntary employee groups that form based on shared characteristics or backgrounds and are sponsored by the organization. Overview The Nexus Water Group team has an opportunity for a Water-Wastewater Operator I. This role is under direct supervision, performs routine tasks related to the operation of water and/or wastewater treatment facilities. Assists with maintaining plant compliance with EPA standards and state water Commission. Performs general cleaning of grounds and buildings. Ensures plant safety and sanitary requirements. Work Location and Schedule This position will travel between service areas near Svannah, GA. Schedule is Monday through Friday. After-hour and weekend on-call support may be required. Must be available to work shift work; weekend scheduling may be required. What You'll Do * Operate and maintain water and/or wastewater treatment equipment, ensuring compliance with state and federal environmental protection limits. and adherence to Company policies and standards. * Conduct ongoing repairs to equipment or shut down equipment for more extensive maintenance and repair, activating alternate equipment as needed. Requests services of outside maintenance vendor for major repairs and overhauls. * Assist Lead Operator with emergency procedures in the event of overflow or spill of chemicals or unpurified water. Follows safety protocol. * Prepare reports and maintain logs on meter readings, tests, chemical and equipment usage, and all other recordkeeping requirements; maintains various Company records and other reports as required by the state. * Clean and maintain treatment plant, pumping stations and wells; prepare and paint equipment, walls, and floors. * Maintain a safe working environment and report safety concerns to Area Manager. * Complete facility and vehicle inspections, along with related follow-up. * Forward customer inquiries on to Operator II or Lead Operator. * Perform other related duties as assigned. What You'll Bring Experience * Requires at least 2 years of mechanical work experience Education and Certification * High school Diploma * must maintain a valid driver's license. * Currently holds first-level operator license per state regulation preferred. Nice to Have * May be in the process of obtaining second-level license * 1 year specializing in chemical treatment of water and/or wastewater and/or a minimum of 1 year in water and/or wastewater utility field with experience in the operation and maintenance of ground-water supplied water systems and associated distribution system preferred. Physical and Technical Skills * Ability to frequently perform moderate to heavy physical demands, including lifting (75 lbs.), walking (10+ miles daily), climbing and mechanical repair. * Ability to read meters, charts and gauges and accurately maintain records of plant operations. * Ability to read and comprehend written technical information and to communicate clearly and effectively, both verbally and in writing. * Ability to review, classify, categorize, prioritize and/or analyze data. * Ability to perform mathematical equations to determine chemical doses required for flow rates and proper treatment. * Ability to establish and maintain effective working relationships with the general public, co-workers and regulatory agencies. * Familiarity with computer applications MS Word, Excel and utilizing tablet and mobile device; ability to learn internal software programs Ability to operate, maneuver and/or control the actions of equipment, machinery, tools and/or materials used in performing essential functions. Work Environment * Company Vehichle Provided * Extreme physical demands, including lifting (75 lbs.), walking (10+ miles daily), climbing and mechanical repair. You will be expected to work in all weather conditions: rain, snow, extreme heat and cold, etc; you may encounter various potential hazards in the field Our Company We are a proud Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, age, disability, protected veteran status or any characteristic or condition protected by Federal, state, or local law. We are an E-Verify participating employer.

Job Description Associate Project Manager - With direction from Senior Project Managers and Manager, manage a cross-functional team of staff and contract resources in the planning, engineering and construction of multiple substation and transmission line projects. Project assignments will comprise of less complex projects supporting GTC programs. For assigned projects, support the scope development process and manage the scoping, estimating, cost and schedule, siting, environmental and regulatory compliance, design, contract management, procurement, land acquisition, construction, commissioning and close-out functions. Manage projects in support of special corporate capital programs. Support the public input process and condemnation activities. Direct project specific relationships with Member Systems and their customers, generation interconnection entities, ITS Members, contractors, consultants and vendors. Ensure the use of approved project methodologies and compliance with Corporate policies and procedures. Ensure timely and accurate reporting of project status to management. Project Manager - Manage a cross-functional team of staff and contract resources in the planning, engineering, and construction of multiple substation and transmission line projects. Project portfolio assignments will comprise large, complex, high-value projects. For assigned projects; manage the scoping, estimating, cost and schedule, siting, environmental and regulatory compliance, public input, design, contract management, procurement, land acquisition, condemnation, construction, commissioning, and close-out functions. Direct project-specific relationships with Member Systems and other customers, regulators, communities, contractors, consultants, and vendors. (PM) Participates in the development and implementation of business processes necessary to manage capital projects effectively. Participates in the process improvement teams. Assists in leading the development and management of Business Alliances and Partnerships with key contractors and vendors. A key participant for ITS coordination of project sponsorship, scope, and technical coordination. Ensure the use of approved project methodologies and compliance with Corporate policies and procedures. Provides training and mentoring to Associate Project Manager. Education: BS in Engineering, Project Management, Construction Management. Experience: Associate Project Manager - Five (5) years in the electric utility transmission projects industry with experience in some of the following areas: scoping, estimating, project control, contract administration, facility siting, environmental/regulatory, land acquisition, design, construction and project management. Project Manager - Five (5) years (PM) of experience in the electric utility transmission projects industry with experience in some of the following areas: scoping, estimating, project control, contract administration, facility siting, environmental/regulatory, land acquisition, design, construction, and project management. Equivalent Experience: Associate Project Manager - Ten (10) years in the electric utility transmission projects industry with experience in some of the following areas: scoping, estimating, project control, contract administration, facility siting, environmental/regulatory, land acquisition, design, construction and project management. Project Manager - Total of ten (10) years of experience. Five (5) years in the electric utility transmission projects industry in some of the following areas: design, siting, project control, land acquisition, and construction. Additional five (5) years of experience in project management of transmission projects. Licenses, Certifications and/or Registrations: Registration, or qualified for immediate registration, as a Project Management Professional (PMP) or as a Professional Engineer in the State of Georgia. Specialized Skills (e.g., typing, computers, software, tools and equipment uses, etc.): Computer Network environment with Microsoft Office. Job Posted by ApplicantPro

Job Description Ready to elevate your career? Join Blue Ridge Mountain EMC as a Full-Time Lineman 3rd Class and experience the thrill of working in the scenic beauty of Young Harris, GA! Imagine climbing power poles against stunning mountain backdrops while contributing to the heart of our community. Here, your problem-solving skills shine as you tackle electrical challenges head-on and ensure safety remains our top priority. At Blue Ridge Mountain EMC, we foster a high-performance, professional culture where your passion for electricity and commitment to integrity will be celebrated. This is an onsite position, allowing you to roll up your sleeves and get involved in hands-on work that makes a tangible impact every day. You will receive great benefits such as Medical, Dental, Vision, 401(k), Life Insurance, Competitive Salary, Paid Time Off, and Employee Discounts. Join us and be a part of something meaningful, all while enjoying the camaraderie of like-minded professionals in a hard-working and dedicated atmosphere! Your day as a Lineman 3rd Class As a Full-Time Lineman 3rd Class at Blue Ridge Mountain EMC, your day-to-day expectations will keep you engaged and on your toes! You'll start each day by reviewing work orders and safety protocols, ensuring everything is set for a successful shift. Your tasks will include assisting in the installation, maintenance, and repair of overhead and underground electrical distribution systems. You'll work alongside seasoned team members, learning to handle tools and equipment safely and effectively. Expect to climb poles, troubleshoot electrical issues, and participate in routine inspections to keep our systems running smoothly. Communication is key, as you'll collaborate with other crew members to solve problems that arise on the job site. You'll also be responsible for upholding our commitment to safety and integrity in every task, making sure you contribute to a high-performance culture that sets us apart! Requirements for this Lineman 3rd Class job To thrive as a Full-Time Lineman 3rd Class at Blue Ridge Mountain EMC, you'll need a mix of practical skills and a proactive mindset! A strong foundation in electrical theory and safety practices is essential, as these will guide you through real-world applications. Excellent problem-solving abilities will help you navigate challenges as they arise, ensuring quick and effective solutions. Physical fitness and stamina are crucial, as the job often involves climbing, lifting, and working in various weather conditions. Strong communication skills will allow you to collaborate effectively with your team, fostering a high-performance environment where everyone contributes to shared goals. Additionally, having a keen attention to detail will ensure you uphold the safety standards and integrity we value. If you're eager to learn and grow in a dynamic team, this role is a perfect fit for you! Get started with our team! If you think this job aligns with your requirements, then submitting an application is simple. Good luck! Offer of employment contingent upon meeting minimum standards in relation to pre-employment background and drug screening Job Posted by ApplicantPro

GardaWorld Security Services is Now Hiring a Concierge Security Officer! ** Must have a valid driver license and clean driving record** Ready to suit up as a Security Guard in a Concierge post? What matters most in a role like this is your ability to build meaningful connections. Tell us about how your natural ability to engage with others reassures and inspires confidence. As a Security Officer - Concierge, there is a high focus on customer service since you will be working with people on all shifts, in environments such as office towers, hotels, shopping centers, etc. What's in it for you: Site Location: Macon, GA Set schedule: 1. Full- time, 10AM - 6PM, Friday - Sunday, Monday, 6AM - 2PM / 2. Sunday - Wednesday, 2PM - 10PM, 2nd shift / 3. Wednesday - Saturday, 10PM - 6AM, 3rd shift Competitive hourly wage of $17.01 /hour (DailyPay is available for GardaWorld employees!) A comprehensive benefits package including medical, dental, and vision insurance plans, a 401(k) retirement savings plan with employer matching contributions, paid time off (PTO) policy, paid holidays, disability coverage, and life insurance options Career growth opportunities at GardaWorld Uniform provided at no cost Responsibilities of a Concierge Security Guard Customer service duties like welcoming, verifying identity, and guiding visitors Manage access control Perform regular patrols to identify potential risks Inspect security equipment and report any maintenance needs Respond to incidents, provide first aid, and coordinate with emergency teams Answer questions in person or by phone Write incident reports and communicate security concerns Ensure the safety and protection of individuals and property Qualifications for Concierge Security Guard Be authorized to work in the U.S. Be able to provide documentation of High School Diploma or GED Valid driver's license is required Be able to ace (and pass) an extensive screening process Exceptional customer service skills Proficient in basic phone & computer skills If you have Security, Military, Law Enforcement experience - even better! You have a state license if required In the United States, GardaWorld Security remains the only guarding security company to be Certified by Great Place to Work. Apply today - this could be more than a job! 26% of our corporate employees started as frontline workers. If you're ambitious with an entrepreneurial spirit - someone who wants to be a GardaWorld Ambassador - a promising career awaits you! GardaWorld Security is a global champion in sophisticated and tailored security solutions, employing and training highly skilled and dedicated professionals across the globe. Not the job for you? Make sure to check out all our jobs! We also have tactical, surveillance, and even casual roles available. Employment is contingent on the successful completion of a background check and drug screening to be conducted after an offer of employment is extended. It is the policy of GardaWorld Security Services to provide equal employment opportunities to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, veteran status, or disability in accordance with applicable federal laws. In addition, GardaWorld Security Services complies with applicable state and local laws governing nondiscrimination in employment. This policy applies to all terms and conditions of employment including, but not limited to hiring, placement, assignment, promotion, termination, layoffs, recalls, transfers, leaves of absence, compensation, and training. It is also the policy of GardaWorld Security Services not to honor requests that employees be assigned on the basis of sex or any other classification protected by law, unless such request is based on a bona fide occupational qualification for that assignment . PSC002179

SA Recycling is one of the largest scrap metal recyclers in the United States. We are growing, growing, growing! Our operations are quickly expanding. SA Recycling proudly supports the military community SA Recycling is looking for a General Laborer .The laborer works on various tasks as assigned. The tasks will include, but are not limited to: general housekeeping, Inspecting metal processing, upgrading, and assisting technical workers. A laborer shall be able to learn new skills on the job, progress to more technical tasks, and become more independent. Work Environment: Scrap metal yard, outdoor Job Duties Including, but not limited to: * Unloading pallets, boxes, and bundles * Material handling / sorting - pushing, pulling, picking, lifting, carrying, and filling up hoppers, boxes, and conveyor belts * Unpacking boxes using box cutters, separating plastics, zip ties, blister packs, and other packaging materials * Disassembling small equipment, cutting wires, torqueing pipefittings, removing bolts, automobile parts, and appliance parts. * Work with recycling equipment for processing metal product e.g. metal shears, band saw and wire strippers * Direct traffic of yard vehicles traveling through yard * Light facility maintenance - painting, scraping, moving furniture and equipment * Maintenance - selecting and using tools properly, pulling and installing parts for machinery, working with other employees to assist machinery repair * Housekeeping - sweeping, cleaning, shoveling, and debris collection * Moderate and Periodic landscaping work * Clean up work area at the end of shift * Keep work areas neat and orderly * Regular attendance and punctuality are essential job functions * Organizing materials to have more effective use of space * Dispose of various waste materials in the appropriate manner * Inspection to ensure cleanup is completed * Effective housekeeping in workplace area is an ongoing operation for safety and better hygienic conditions for all team members. Qualifications * Employees in this position prior to April 2014 are presumed to be qualified and are "grandfathered" into their positions. * Must pass a medical physical and drug test * Must pass a background check * Preferred - high school diploma or GED and/or foreign education acceptable * Bi-lingual (English & Spanish) language skills a plus * Ability to: communicate with others effectively; understand direction (written or oral) and use basic math skills as the job demands * Willingness to learn how to: sort metal, identify colors, shapes, and weights; properly maintain equipment; properly utilize PPE Physical Requirements * Work Environment: Scrap metal yard, outdoor * Equipment & Tools: Yard equipment, hand tools, and PPE. * Physical Demand Level: Moderate to heavy * Work Capacity: Laborer Work Capacity * Sensory Demands: Hearing, vision, smell, touch and taste * Hand Movements: Repetitive motions, gripping * All weather Job Expectations Comply with all applicable federal, state, local, & SA Recycling safety, health, & environmental rules, regulations, policies, & procedures. SA Recycling offers: * Competitive Pay * Eligible for Safety and Performance Bonuses * Comprehensive benefits including affordable medical options, dental and vision care * 401k with a Company Match * Growth opportunities and promotions from within * Weekly Pay * Referral Incentives * Company provided uniforms and PPE PLEASE NOTE: The above statements are intended to describe the general nature and level of work being performed by people assigned to this job. They are not intended to be an exhaustive list of all responsibilities, duties and skills required. An offer of employment by SA Recycling is contingent on the satisfactory completion of a post-offer drug screen, physical exam, and background check with a credit check (if position specified). All US applicants must be 18 years of age or older.

Job Description Responsible for the performance, operations and maintenance of simple-cycle combustion turbine technologies and generating assets in a manner which optimizes reliability, availability and O&M costs while maintaining the highest standards in safety, environmental, and NERC electrical reliability. Technician must understand and apply concepts to operate the equipment and perform plant systems analysis to take actions for identifying, resolving and/or avoiding failure modes. In addition, the individual performs operator rounds, troubleshooting, preventive, corrective and predictive maintenance on plant systems/equipment to ensure safe, efficient, and reliable plant operations, as well as enhance equipment longevity. The incumbent is responsible for continuous improvement and providing reliable and efficient electric power generation in compliance with corporate safety policies and procedures, environmental, mandatory electric reliability standards, FERC, EPA, EPD, OSHA, DOT and all applicable governmental regulations. Job Duties: Responsible for daily plant operations and maintenance to ensure safe, efficient, and reliable plant operations, complying with corporate policies and procedures, and all governmental regulations. Must strive to achieve dispatch orders and keep GSOC informed of all changes in plant capability. Daily activities include start-up and shutdown of the plant equipment, operator rounds, oversee plant physical security, clearances, receiving materials/inventory, maintaining 3-part communications with GSOC, shift log communications, and issuing applicable Operational Advisory and Event Reports. Documenting and communicating operational or maintenance conditions and activities to allow the efficient and orderly transfer of information to others. Responsible for assigned work orders and systems ownership. Compliance with the Conduct of Maintenance Program engaging in the 4-week and outage planning and preparations, including reviewing, updating or developing Job Plans, ordering parts and updating inventory requirements. Take appropriate corrective actions to address abnormal conditions, engage supervisor and other resources, and utilize MAXIMO work order/management processes. Complete required reporting, documentation, change management control and VAULT drawing updates. Maintain individual safe work practices while performing duties, including completing required training, understanding and following the OPC Safety Manual/Procedures. Perform the function of Clearance Authority for establishing and maintaining safe isolation of equipment/device for the protection of all personnel performing work within established boundaries. In addition, participate in monthly safety meetings and complete all required training to ensure personal compliance, safe work practices, operational excellence, and technical knowledge. Responsible for administration of contracts as assigned and coordination of contract support services as required. This project/contract management may include capital project scoping document preparation, budget management, contractor oversight, status reports, and administrative duties as required. Compliance Reporting, responsible for the preparation of required documentation and reports to the Corporation's local, division and senior management, owners, regulatory authorities and other agencies to assure compliance with regulations and the terms of the Management Services Agreement. Maintains job related qualifications, system knowledge, and understanding of OPC policies and procedures (Emergency Action Plan, Environmental Baseline Book, SERC Plant Level Procedures, etc...). Required Qualifications: Education: High School Diploma or equivalent required. Associate's degree in engineering, engineering or related physical science, or equivalent preferred. Experience: Six years' experience in operation or maintenance of an operating commercial power production facility, a large natural gas facility, or combustion turbine driven naval vessel. Equivalent Experience: Eight years' experience in operation or maintenance of an operating commercial power production facility, a large natural gas facility, or combustion turbine driven naval vessel. In addition, a highly developed analytical and technical problem-solving background. Specialized Skills: A strong ability to work in a team environment. An effective trainer of personnel and one that motivates others to succeed. The ability to extract, comprehend and develop instructions from technical manuals, journals, and drawings, technical literature and other job related material. The ability to effectively communicate orally and in writing using the English language. The ability to effectively use control systems (such as Siemen T3000, GE Mark V/VI, Allen Bradley PLCs, etc...) and computer applications (such as Outlook Email, MSOffice Suite, IBM-Maximo and Vault). Possess independent decision-making capabilities in stressful situations with minimum supervision. The ability to troubleshoot electrical, instrument and mechanical systems for malfunctions. The ability to work on and around high-voltage electrical equipment. The ability to instruct others in the performance of testing, checkout and troubleshooting of equipment. The ability to provide technical direction and leadership to Assistant Combustion Turbine Technicians and contractors brought in to augment the workforce in the performance of modifications and major repairs to The ability to perform predictive maintenance and interpret data on plant equipment performance. The ability to perform basic management and supervisory skills when needed. Licenses, Registrations, and/or Certifications: Valid driver's license which meets the insurance eligibility requirements under Oglethorpe Power's qualification program. Travel: 15% Job Posted by ApplicantPro