Assembler jobs in Ladera Ranch, CA

Under minimal supervision, the Assembler III performs optical and mechanical assembly of high complexity requiring fitting, alignment and adjustment of components, units and assemblies to very close tolerances. Primary Duties & Responsibilities * Clean and assemble various optical parts, mechanical subassemblies and large assemblies of high complexity. * Requires the use of hand tools to perform a wide variety of electronic or electro-mechanical, mechanical or measurement product assembly operations on assemblies or sub-assemblies. * Determines and/or follows methods and sequence of operations in performing wiring, component installation, hand soldering and cable harnessing, and fitting on assembly units. * Solders onto various parts as required by assembly instructions. * Primes and bonds optical surfaces to other optical or mechanical components. * Reads detailed, complex blueprints, assembly sketches and procedures with very little supervision. * Fits or adjusts parts or assemblies within established guidelines. * Inspects and test finished items or assemblies. Education & Experience * High School Diploma or (GED) * 4 years of experience in similar assembly operation. High level of manual dexterity, Knowledge of an ability to use a wide variety of hand tools and knowledge of soldering. * Soldering certification is required * Basic computer navigation skills are required * Experience with optical handling, inspection and gluing are highly desired Skills * Mathematical Skills * Ability to calculate figures and perform simple addition, subtraction, multiplication and division of whole numbers and fractions. * Language Skills * Ability to read and interpret documents such as safety rules, operating and maintenance instructions, procedure manuals and blueprints. * Reasoning Ability * Ability to apply common sense understanding to carry out instructions furnished in written, oral or diagram form. * Ability to deal with problems involving several concrete variables in standardized situations. Working Conditions * Job operates in production environment on 1st shift, Mon-Fri. * Typically works in a lab environment with some time in an office near the work areas. Some work requires the use of hazardous chemicals. * Noise level - Usually moderate Physical Requirements * Standing. Particularly for sustained periods of time. * Working with Hand / Fingers. Picking, pinching, typing or otherwise working, primarily with fingers rather than with the whole hand as in handling. * Lifting. Raising objects from a lower to a higher position or moving objects horizontally from position-to-position. This factor is important if it occurs to a considerable degree and requires substantial use of upper extremities and back muscles. Safety Requirements All employees are required to follow the site EHS procedures and Coherent A&D EHS standards. Quality and Environmental Responsibilities Depending on location, this position may be responsible for the execution and maintenance of the ISO 9000, 9001, 14001 and/or other applicable standards that may apply to the relevant roles and responsibilities within the Quality Management System and Environmental Management System. Culture Commitment Ensure adherence to company's values (ICARE) in all aspects of your position at Coherent A&D: Integrity - Create an Environment of Trust Collaboration - Innovate Through the Sharing of Ideas Accountability - Own the Process and the Outcome Respect - Recognize the Value in Everyone Enthusiasm - Find a Sense of Purpose in Work Coherent A&D is an equal opportunity/affirmative action employer. All qualified applicants will receive consideration for employment without regard to sex, gender identity, sexual orientation, race, color, religion, national origin, disability, protected Veteran status, age, or any other characteristic protected by law. This role involves access to technology, materials, software, or hardware subject to U.S. export control laws. Therefore, to be considered, candidates must be classified as a "U.S. Person" under applicable regulations or be eligible for authorization under a U.S. government export license.

About the Company: DwyerOmega is a globally trusted leader in manufacturing innovative instrumentation solutions for the Process Measurement, Automation, Control and HVAC markets. With very strong brand recognition and high levels of customer loyalty, DwyerOmega has an unmatched reputation for providing customized solutions that meet and exceed customer needs. Our team of engineering experts help our customers select technical, and often configured, product solutions for their unique applications. The company offers over 300,000 state-of-the-art products for process measurement and control of temperature, humidity, pressure, strain, force, flow, level, pH, conductivity, and indoor air quality, and is a recognized global leader in the digital marketing of technical products. The products that we manufacture are used to control and drive process efficiency, creating safe and sustainable environments. At DwyerOmega, we enable our customers to improve the world - one measurement at a time. We achieve this through our unwavering commitment to technology, customer service, and overall continuous improvement. Every day, we strive to cultivate a culture of ingenuity, empowerment, accountability, adaptability, and speed. The company's corporate headquarters are based in Michigan City, Indiana, and Norwalk, CT with manufacturing locations and sales offices located throughout the world. Analytical Industries: Analytical Industries is a leading provider of advanced gas analysis and measurement solutions for industrial, medical, and environmental applications. We take pride in our engineering excellence, precision manufacturing, and commitment to helping customers achieve accurate, reliable process control. As part of the DwyerOmega family, we bring together decades of instrumentation expertise and customer-focused innovation. Position Summary: The Assembler is responsible for assembling, wiring, soldering, testing, and inspecting small electro-mechanical components used in sensor and analyzer products. This position requires close attention to detail, steady hands, and adherence to established quality and safety standards. Working under the direction of the Lead or Production Manager, the assembler follows detailed assembly instructions, performs accurate and repetitive work, and supports overall production efficiency. The role also includes maintaining a clean and organized work area and performing all other duties as assigned. Responsibilities include the following. Other duties may be assigned. * Assemble electrochemical sensors and electromechanical analyzers, and related subcomponents according to engineering drawings, schematics, and work instructions. * Perform wiring, soldering, and mechanical assembly using hand tools and electronic testing equipment. * Log production results, nonconformities and test outcomes accurately in manufacturing documents such as the DHR. * Inspect components before assembly for defects or non-conformance. * Maintain a clean and organized work area in accordance with safety and 5S practices. * Collaborate with engineering and quality teams to identify assembly issues and propose process improvements. * Follow all company policies related to safety, quality assurance, and environmental compliance. Requirements Essential/Preferred Skills: * 1-2 years of work experience in electro-mechanical assembly, preferably in sensor instrument manufacturing. * High school diploma or GED equivalent. * Ability to read and interpret drawings, schematics, and work instructions. * Prior experience with hand tools. * Strong attention to detail and commitment to product quality. Work Conditions and Physical Requirements: * Work performed primarily in an office/manufacturing space. * Frequent sitting, standing, bending, and using small tools. * May involve handling chemicals used in assembly rooms. * Use of PPE (gloves, safety glasses) as required. * May require repetitive motions to maintain quality of sensor/analyzer products.

This position is responsible for the assembly and leak testing of UHP equipment, which includes but is not limited to: working in clean room, glove box operation, assembly, testing, inventory control, and data entry. Must be able to read blueprints and follow work instructions. * Performs other duties as assigned * Complies with all policies and standards QUALIFICATIONS Work Experience Experience Experience Details Required/ Preferred 1-3years 4-6years 7-9 years Knowledge, Skills and Abilities * PHYSICAL DEMANDS/WORKING CONDITIONS Physical Demands Category: Physical Demands A thorough completion of this section is needed for compliance with legal standards such as the Americans with Disabilities Act. The physical requirements described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Physical Demand N/A Rarely Occasionally Frequently Constantly Weight Stationary Position Move/Traverse Stationary Position/Seated Transport/Lifting Transport/Carrying Exerting Force/Pushing Exerting Force/Pulling Ascend/Descend Balancing Position Self/Stooping Position Self/Kneeling Position Self/Crouching Position Self/Crawling Reaching Handling Grasping Feeling Communicate/Talking Communicate/Hearing Repetitive Motions Coordination Compensation: $23 per hour The Company is an Equal Opportunity Employer that complies with the laws and regulations set forth under EEOC.. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability or protected veteran status. EOE AA M/F/VET/Disability

This position requires the assembling of parts according to instructions and within a specific time frame, while using the appropriate tools and/or equipment according to safety and quality standards, as well as carrying out any other duties as directed by the Leadman or Supervisor. ESSENTIAL FUNCTIONS Read, interpret and follow basic blueprints, diagrams, engineering drawings, specifications, bills of materials, and other written instructions or procedures to accurately assemble equipment and products Perform quality work checks to insure the product meets quality standards Identify product defects and complete appropriate documentation when defects are identified Perform all work in accordance with quality standards and established safety procedures Maintain a clean and safe work area Assembling units as directed by the trainer, Lead or Supervisor with quality in mind in a specified time frame. Performed adjustments needed to ensure factory settings and specifications using schematics and/or engineering documentation. Must be able to lift up to 25 pounds. Must be able to climb up ladders. May be required to work beyond normal business hours when necessary. Supporting company policies and procedures, goals and objectives, ISO policies, and good manufacturing practices. NON-ESSENTIAL FUNCTIONS Regularly perform repetitive tasks Specific vision abilities required include close vision, distance vision, color vision, peripheral vision, depth perception, and the ability to adjust focus Ability to perform work accurately and thoroughly Ability to use thinking and reasoning to solve a problem and to think in such a way as to produce a new concept or idea Demonstrate commitment to an Injury-Free Environment through own actions and mentoring others. Communicate and enforce corporate environmental, health, and safety program. Fill out forms, as need. REPORTING RELATIONSHIP Laser Supervisor Laser Lead SUBORDINATE STAFF None KNOWLEDGE Forklift and Overhead Crane Preferred. Be able to use the metric system. Must be a good communicator. Must be able to use Hand Tools and Power Tools. Must have assembly experience. Enthusiastic, cooperative, and positive behavior. ISO experience a plus. SKILLS High attention to detail and self-motivation skills Basic reading skills. Must be able to follow directions Basic computer navigation and utilization skills Must be able to use addition, subtraction, multiplication and division. Must be able to work in a team and follow deadlines. Must have good leadership and communication skills. WORK SCHEDULE 10/4 Schedule Monday - Thursday 6:00am - 5:00pm PAY RANGE $24.00-$26.00/HR EDUCATION and QUALIFICATION High School education preferred. MENTAL Ability to accept and follow instructions. Being open to feedback from peers, Leadman and Supervisor. Realize one's own limitations and seek assistance when needed.

Preferred Job Qualifications: Previous experience in aerospace manufacturing or related industries familiarity with inspection processes and basic quality standards Ability to perform polishing and cleaning and packaging with attention to detail. Forklift certification or proven forklift operating experience. Ability to safely lift and move materials as required. Strong organizational and time management skills valid driver's license with a clean driving record Ability to follow written and verbal instructions accurately. Commitment to safety protocols and workplace cleanliness Strong teammate skills with the ability to work independently when needed. Physical and Mental Requirements: Able to lift 25 pounds regularly. Ability to sit or stand for extended periods. Must be adaptable to a constantly changing environment and perform well under deadlines. Experience and Education: Previous experience in a similar role is preferred but not required. Must demonstrate the ability to learn and apply new skills effectively. We are looking for motivated individuals who can contribute to our team-oriented environment and handle the demands of a high-paced production setting. Please note that this job description is not exhaustive. Management reserves the right to add, modify, change, or rescind work assignments or different positions and to make reasonable adjustments to ensure qualified employees can perform the essential functions of the job. Hourly Rate of Pay: $18.00/ hour to $20.00/ hour **Please note that the salary range information is only applicable to California. The pay range represents the low and high end of the salary range we reasonably expect to pay for this position at the time of posting. An employee's pay position within the salary range will be based on several factors, including, but not limited to, geographic location, experience, education, skills, qualifications, performance, and business or organizational needs. Equal Opportunity Employer: Western Precision Aero is an Equal Opportunity Employer and all employees of RBC are subject to E-Verity. Due to ITAR regulations, this position requires that the employee must be a U.S. Person (U.S. Citizen or Permanent Resident) or a Foreign Person for whom a license is obtained.

Assembly Technician Job Description Schedule & Pay Hours: 9:00 AM - 6:00 PM (Day Shift) Pay Range: $20 - $22 per hour Overtime: As needed Responsibilities Assemble skid units and industrial equipment Interpret assembly drawings and measurements accurately Operate weld machines, cutting tools, and other industrial tools Assist in other production areas (Warehouse Inventory, Shipping & Receiving, Packing) Maintain safety awareness at all times Undertake additional training as required for new tools/techniques Demonstrate professionalism, consistency, and effective communication skills Qualifications 3-5 years of experience in manufacturing or fabrication Experience working with rotating equipment Ability to properly operate industrial machinery Strong understanding of measurements and assembly drawings High School Diploma or GED required Additional Information Physical Demands: Must be able to lift up to 50 lbs.; pass physical and lift assessment Working Conditions: Shop environment Training/Certifications: Not required Travel: Not required KPG123

Beta Bionics, Inc. is a medical technology company dedicated to bringing innovative type 1 diabetes management solutions to the many, not the few. We are committed to bringing better access to better solutions - and a better life for those living with diabetes - with the world's first bionic pancreas called the iLet. The iLet Bionic Pancreas is the first and only insulin delivery system that does not require carb counting*, bolusing, correction factors, or pre-set basal rates. The only number needed to get started with the iLet Bionic Pancreas is a user's weight - the iLet does the rest. The iLet lets users “Go Bionic” with their diabetes management. Beta Bionics is a public benefit corporation. This means we are a for-profit company with obligations to serve both our public benefit mission and shareholders' interests. Beta Bionics is also a certified B Corporation; and as such accountable to operate with high standards of transparency, sustainability and accountability to our customers, employees, business partners, society, and the environment. Successful candidates will be working with highly experienced colleagues, who are amongst the best in their fields. We have a mission-driven, passionate and collaborative culture where you will have a high degree of empowerment and opportunity to make a significant impact. Please contact us if you fit the profile below and if you are interested in joining the Beta Bionics team! *User must be carb aware. *Contract to Hire Summary/Objective: The Assembler I will perform duties associated with electro-mechanical and clean room device assembly and packaging. The critical attributes and skills required for this position include manual hand assembly skills, attention to detail, initiative, working well within a team, and ability to produce consistently high-quality results.. Essential Duties and Responsibilities [Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Qualified candidates who need a reasonable accommodation with the application process and/or to perform the essential functions of the position should notify the company's HR contact] Support company goals and objectives, policies and procedures, Good Manufacturing Practices, and FDA regulations including compliance to EN ISO 13485, Medical Device Quality Standards. Comply with company Standard Operating Procedures (SOPs) and departmental policies and procedures (DOPs), objectives, the quality assurance program, as well as safety and environmental standards. Ability to establish, build and maintain professional working relationships with all levels of staff, clients, and suppliers. Excellent interpersonal, verbal, and written communication skills. Meticulous attention to detail and meeting deadlines. Ability to learn new equipment and processes, and quickly demonstrate proficiency in their operation. Read and interpret manufacturing procedures, engineering drawings, and inspection procedures and comply with their requirements. All documents are written in English. Demonstrates accuracy, thoroughness and monitors own work to ensure quality. Practice and always advocate good safety skills. Education and Experience Experience in FDA/GMP/ISO environment preferred Excellent interpersonal, verbal, and written communication skills. Meticulous attention to detail 2+ years of experience in a medical device environment preferred. Location & Position Details This position is based out of our office in Irvine, California 92618 Contract to Hire Pay Rate $19.00 per hour Hours Swing Shift: Mon - Thurs, 3:30pm - 2:00am + 5% comp (trains on 1st shift for first couple of weeks) Weekend Shift: Fri - Sun, 5:00am - 5:00pm + 7% comp (trains on 1st shift for first couple of weeks) Work Environment Works in a Lab, Clean Room, and Warehouse environment, within a well-lighted work area with good ventilation and normal noise levels from lab, shop equipment, and clean room. Sitting or standing at a production workstation with frequent walking to transact product; intermittently write or use a keyboard to communicate through written means. Physical Demands While performing the duties of this job, the employee is regularly required to stand; walk; sit; use hands to handle or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch, see, talk or hear. Specific vision abilities required by this job include close vision, color vision, and ability to adjust focus. Employee must occasionally lift and/or move up to 40 pounds. Wears personal protective equipment as required. Equal Employment Opportunity Statement It is the policy of Beta Bionics to provide equal employment opportunity to all persons regardless of age, color, national origin, citizenship status, physical or mental disability, race, religion, creed, gender, sex, sexual orientation, gender identity and/or expression, genetic information, marital status, status with regard to public assistance, veteran status, or any other characteristic protected by federal, state or local law. In addition, Beta Bionics will provide reasonable accommodations for qualified individuals with disabilities.

Temp To Full-Time Skillset Group is seeking a Wire Harness Assembler to work in the Irvine, CA area. This position will under shop supervision the Inspect and perform work in accordance with IPC-A610 and other quality standards as needed. This will be a 1st shift position and will be contract to hire. To apply email: ************************* Pay: $30-$33/hr,

About us: Karman Space & Defense provides concept-to-production solutions for mission-critical systems on spacecraft, launch vehicles, missiles, hypersonics, and integrated defense systems. We believe that solving the industry's most complex and mission-critical challenges requires relentless determination and a willingness to push the boundaries of possibility. Karman Space & Defense brings to bear unparalleled production capabilities, unmatched engineering expertise, and unflinching analysis to render the impossible, possible. We are looking for Assemblers! Pay: $17-$18 Location: Brea, CA KNOWLEDGE AND SKILL REQUIREMENTS: Ability to use hand tools Able to use appropriate measuring devices, such as calipers, micrometers, height gages, plug gages, etc. Maintain a clean work area daily as required Must work closely with the CNC Programmer MUST BE ABLE TO TRAIN ON THE 1st SHIFT AND TRANSITION TO 2nd SHIFT COMPANY BENEFITS: Medical Dental Vision Life 401k Tuition Reimbursement Paid Holidays Employee Referral Program If an exciting career in the Space & Defense Industry is for you, we'd LOVE to talk to you! ITAR REQUIREMENTS: To conform to U.S. Government export regulations, applicant must be a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (aka green card holder), (iii) Refugee under 8 U.S.C. § 1157, or (iv) Asylee under 8 U.S.C. § 1158, or be eligible to obtain the required authorizations from the U.S. Department of State. Learn more about the ITAR here. KARMAN SPACE & DEFENSE: Karman is the market leading suppliers of metallic and composite flight hardware and sub-assemblies for the space, missile, and hypersonic markets. Karman offers an unprecedented capability set to customers, creating a supply chain solution in a historically fragmented supply base. The Karman team draws on in-house expertise in engineering & design, precision machining, large part forming, welding, heat age, finishing, assembly, ablative & insulative composites, and other capabilities to serve as a strategic partner to customers. Karman is headquartered in greater Los Angeles and currently has 5 locations in Southern California and 1 location in Mukilteo, Washington. Equal Opportunity Employer/Protected Veterans/Individuals with Disabilities. The contractor will not discharge or in any other manner discriminate against employees or applicants because they have inquired about, discussed, or disclosed their own pay or the pay of another employee or applicant. However, employees who have access to the compensation information of other employees or applicants as a part of their essential job functions cannot disclose the pay of other employees or applicants to individuals who do not otherwise have access to compensation information, unless the disclosure is (a) in response to a formal complaint or charge, (b) in furtherance of an investigation, proceeding, hearing, or action, including an investigation conducted by the employer, or (c) consistent with the contractor's legal duty to furnish information. Karman is committed to equal employment opportunity. We will not discriminate against employees or applicants for employment on any legally recognized basis (“protected class”) including, but not limited to race; color; religion; genetic information; national origin; sex; pregnancy, childbirth, or related medical conditions; age; disability; citizenship status; uniform servicemember status; or any other protected class under federal, state, or local law. Our management is dedicated to ensuring the fulfillment of this policy with respect to hiring, placement, promotion, transfer, demotion, layoff, termination, recruitment advertising, pay, and other forms of compensation, training, and general treatment during employment. 1st Shift | 6:00 AM to 4:30 PM | Monday-Saturday 2nd Shift 4:00 PM to 12:45 AM - Monday-Friday, Saturday (6hours)

Job DescriptionJoin Siemens in Pomona, CA At Siemens, we bring the real and digital worlds together to drive sustainable progress. Your growth matters to us, and you'll be part of a diverse team that supports and challenges you to learn in new ways. What a typical evening looks like You arrive for 2nd shift at 4:00pm, ready to dive into the day's production plan. After three months of onboarding on 1st shift, you'll be fully immersed in evening operations until 12:30 Midnight, keeping our switchboards and lighting panels moving through the line. You review work orders on your station computer, scan in, gather materials, and begin assembling. Use hand and power tools to build and modify electromechanical assemblies (switchboards, lighting panels, and related equipment). Follow blueprints, bills of materials, and one-line diagrams to complete assigned builds. Fasten and secure parts to frames/cabinets, create subassemblies, and complete unit assemblies. Process, scan into/out of work orders and track progress according to schedule or expedited priorities. Keep equipment and your work area clean to maintain safe, reliable operations. Compensation and Schedule Pay $19.22 Location: Pomona, CA 2nd shift: 4:00pm - 12:30 Midnight Training: 3 months on 1st shift What you'll bring Comfort with basic computers and fundamental mechanical/measuring tools. Ability to read, write, speak, and understand English. Capacity to stand for extended periods and handle physical tasks. Reach, grasp, and lift up to 50lbs; push/pull/slide heavy materials. Ability to stoop, bend, squat, crawl, and climb. At least 18 years of age. Detail oriented, able to multi-task in a fast-paced production environment. Eager to learn all equipment in the facility and follow defined processes. Legally authorized to work in the United States on a continual and permanent basis without company sponsorship Preferred experience Exposure to blueprint reading. Background working with large industrial machinery. Core proficiencies Mechanical assembly Blueprint reading Bring your hands-on skills and curiosity-together we'll power what matters.

Under general supervision, performs a wide variety of electromechanical or mechanical production sub-assembly and assembly operations to build up and assemble difficult and complex instruments. Duties may include following techniques to wire, prepare cable harnesses and install cable harnesses. Perform coating, mixing and cooking of raw materials to create finished products. Essential Job Functions Assembly Activities Under general supervision, performs various tasks requiring knowledge of assembly techniques, tools, materials, machines and equipment. Assembles electromechanical instruments or fabricated parts to make subassemblies or complete instruments using hand tools, power tools and special tools and/or calibration equipment. Determines methods and sequence of assembly operations where complete information is not readily available or follows assembly shop and production operations sheets, wire lists, samples, blue prints, schematics and verbal instructions to perform a wide variety of assembly operations. Fits, aligns, calibrates and adjusts parts and mechanisms to meet tolerances and product operating and quality requirements. Works from engineering drawings, rough sketches, and manuals, verbal or written instructions from Lead Assembler or Supervisor. Performs in-process and final quality inspection of assembled products. Examines drawings and work orders to determine the work that needs to be performed. Utilizes appropriate machines and tools to install, mount, fasten, align and adjust parts, components, wiring and harnesses. Evaluates assembly procedures and manuals and recommends revisions when required. Performs such tasks as replacing components and wiring circuits. Trains new hires and co-workers as necessary to enhance skill level and knowledge base. Examines and tests assembly at various stages of production to identify errors. Maintains a record of the assembly process, progress and problems. Provides feedback to supervisor when a deviation from accepted practice or safety issues are recognized. Utilizes small hand tools such as wire strippers, crimpers, wrenches, screwdrivers, pliers, and hammers. Identifies and selects components to be integrated into sub-assembly and assembly units. Makes own set-ups, alignments and adjustments maintaining tolerance in accordance with instructions. Disassembles, modifies, reworks, refurbishes, reassembles, and tests instruments as required. Clean and coat molds for fixtures and product used. Perform mixing and cooking of gels in a laboratory environment. Other Activities Evaluates and recommends changes in methods and procedures in assigned area of responsibility. Performs data entry on work-in-process transaction and parts ordering. Recommends and implements methods to promote teamwork and maintains a pleasant work environment within department and with other departments. Trains new team members on how to fill out DHR such as batch record and traveler during the production run. Seeks constant improvement in work processes and techniques. Assures that laboratory and assembly areas are in an orderly and functional condition. Suggests improvement in departmental work processes and procedures. Maintains good communications with peers, Lead Assembler and Supervisor. Attends and participates in group meetings, task force groups, etc., as needed. Works with Support Engineering to develop and maintain time standards. Aids Support Engineering with design of assemblies and units for manufacturing capability. Performs other duties and projects as assigned by Supervisor and/or Lead Assembler. Essential Job Requirements Education High school diploma, GED or equivalent education and experience. Experience & Minimum Qualifications 4-6 years of assembly experience in a fast-paced manufacturing environment Ability to follow schematics and assemble wire harnesses is a must. Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals, engineering prints and schematics. Ability to add, subtract, multiply and divide in all units of measure, using whole numbers, common fractions, and decimals using a calculator. Ability to compute rate, ratio and percent, and to draw and interpret bar graphs. Ability to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization exists. Ability to interpret a variety of instructions furnished in written, oral, diagram, or schedule form. Ability to use standard power hand tools and custom tools, gauges, and other calibration equipment and assembly fixtures. Ability to lift 25 to 50 pounds is an asset Strong organizational skills through demonstrated ability to multi-task and manage time Established collaboration skills and the ability to communicate with openness and transparency. Ability to comply with FDA Good Manufacturing Practices (GMP). Ability to meet production schedules and project deadlines. Exposure and training to Six Sigma and/or lean manufacturing preferred. Physical Requirements & Working Environment Ability to work safely and according to departmental procedures when working at high temperatures with hazardous equipment and materials such as oven, mixers, hot plates, ultrasonic cleaner, pressure cooker, fume hood, power tools, wire strippers, heat guns, heated cutting blades and others. Ability to work safely and according to departmental procedures when handling volatile chemicals which may or may not be hazardous. Ability to work safely in a chemical laboratory environment. Ability to occasionally lift and/or move up to 50 lbs. Ability to successfully respond to multiple work pressures. Ability to communicate verbally to individuals and groups. Ability to communicate verbally in person and using a phone. Ability to listen for understanding and assisting in problem solving. Ability to regularly use hands to utilize maximum dexterity. Ability to frequently to walk, stand, sit, and reach with hands and arms. Ability to occasionally to stoop, kneel, crouch, or crawl and hear. Specific vision abilities required include close vision, color vision, and ability to adjust focus. "Sakura Finetek USA, Inc. is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex including sexual orientation and gender identity, national origin, disability, protected Veteran Status, or any other characteristic protected by applicable federal, state, or local law.” The above description identifies the essential job functions and skills needed by the person or persons assigned to this position. These job functions and skills are not intended to be a complete and exhaustive list of all responsibilities, duties and skills required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential job functions. The information contained herein is subject to change at the company's discretion.

Job Posting Start Date 12-09-2025 Job Posting End Date 01-09-2026 Crown Technical Systems, a Flex Company, is a leader in power distribution and protection systems concentrating on sophisticated, state-of-the-art relay and control panels, medium voltage switchgear, and enclosures (power/control buildings/ E-Houses). We specialize in customized, turn-key solutions that ensure safe, secure, and reliable power distribution. Working at Crown Technical Systems offers a dynamic and rewarding career path for individuals seeking to power the world. Through hands-on training, mentorship, and a culture of internal promotion, we empower you to reach your full potential and contribute to projects that truly matter. Job Summary To support our extraordinary teams who build great products and contribute to our growth, we're looking to add a/an Panel Assembler in USA, Fontana Ca. Reporting to the Production Manager the Panel Assembler is responsible for assembling fabricated metal parts for relay and control panels according to specifications. What a typical day looks like: Review, analyze, and follow various blueprints, diagrams, drawing, procedures, and work instructions to complete assemblies for relay and control panels. Assemble relay and control panel metal cabinets Uses various power tools and hand tools (ex. Drills, impacts, screwdrivers, grinders, etc.) to accomplish assigned tasks Conduct quality assurance checks to confirm that assembled products meet specifications and quality standards Identify any product defects; record and report them accordingly Monitor and maintain inventory of necessary supplies, tools, and parts in work station Maintain a clean and safe work area Perform all other duties as assigned The experience we're looking to add to our team: High School Diploma or equivalent 0-2 years of related experience in assembly or manufacturing setting Prior experience operating powered equipment (forklift, reach truck, scissors lift, overhead crane, etc.) Strong attention to detail and ability to perform work accurately Knowledge of manufacturing, equipment maintenance, and safety management Reading comprehension skills with the ability to interpret and follow written directions, blueprints, wiring drawings, schematics, and engineering diagrams Basic math skills to meet technical specifications and measurements Basic understanding of tools (ex. Tape measure, impact drill, etc.) Demonstrated proficiency with the ability to safety operate powered equipment (forklift, reach truck, scissors lift, overhead crane, etc.) What the physical requirements are: Prolonged periods of standing, bending, kneeling, and performing repetitive tasks. Must be able to lift, push, pull up to 35 pounds at a time. Must have manual dexterity in order to assemble products or machines as directed. Must have excellent hand-eye coordination. Ability to differentiate between colored wires, tabs, and electronic components. Must wear PPE, such as gloves, safety glasses, hard hat, and ear protection, while working on the production floor #LI-GB1 What you'll receive for the great work you provide: Full range of medical, dental, and vision plans Life Insurance Short-term and Long-term Disability Matching 401(k) Contributions Vacation and Paid Sick Time Tuition Reimbursement Pay Range (Applicable to California)$17.98 USD - $24.27 USD HourlyJob CategoryOperations Is Sponsorship Available? No Crown is an Equal Opportunity Employer and employment selection decisions are based on merit, qualifications, and abilities. We do not discriminate based on: age, race, religion, color, sex, national origin, marital status, sexual orientation, gender identity, veteran status, disability, pregnancy status, or any other status protected by law. We're happy to provide reasonable accommodations to those with a disability for assistance in the application process. Please email accessibility@flex.com and we'll discuss your specific situation and next steps (NOTE: this email does not accept or consider resumes or applications. This is only for disability assistance. To be considered for a position at Crown, you must complete the application process first).

Job Posting Start Date 11-25-2025 Job Posting End Date 01-30-2026 Crown Technical Systems, a Flex Company, is a leader in power distribution and protection systems concentrating on sophisticated, state-of-the-art relay and control panels, medium voltage switchgear, and enclosures (power/control buildings/ E-Houses). We specialize in customized, turn-key solutions that ensure safe, secure, and reliable power distribution. Working at Crown Technical Systems offers a dynamic and rewarding career path for individuals seeking to power the world. Through hands-on training, mentorship, and a culture of internal promotion, we empower you to reach your full potential and contribute to projects that truly matter. Job Summary To support our extraordinary teams who build great products and contribute to our growth, we're looking to add a/an Building Assembler in USA, Fontana Ca. Reporting to the Production Manager, Building Assembler is responsible for assembling fabricated metal parts for enclosure buildings according to specifications. What a typical day looks like: Review, analyze, and follow various blueprints, diagrams, drawing, procedures, and work instructions to complete assemblies for enclosure buildings Assemble and install electrical components including panel boards, HVAC units, battery systems, electrical devices, and bending conduit Uses various power tools and hand tools (ex. Drills, impacts, screwdrivers, grinders, etc.) to accomplish assigned tasks Conduct quality assurance checks to confirm that assembled products meet specifications and quality standards Identify any product defects; record and report them accordingly Monitor and maintain inventory of necessary supplies, tools, and parts in workstation Maintain a clean and safe work area Perform all other duties as assigned The experience we're looking to add to our team: High School Diploma or equivalent 0-2 years of related experience in assembly or manufacturing setting Prior experience operating powered equipment (forklift, reach truck, scissors lift, overhead crane, etc.) Strong attention to detail and ability to perform work accurately Knowledge of manufacturing, equipment maintenance, and safety management Reading comprehension skills with the ability to interpret and follow written directions, blueprints, wiring drawings, schematics, and engineering diagrams Basic math skills to meet technical specifications and measurements Basic understanding of tools (ex. Tape measure, impact drill, etc.) Demonstrated proficiency with the ability to safely operate powered equipment (forklift, reach truck, scissors lift, overhead crane, etc.) What the physical requirements are: Prolonged periods of standing, bending, kneeling, and performing repetitive tasks. Must be able to lift, push, pull up to 35 pounds at a time. Must have manual dexterity in order to assemble products or machines as directed. Must have excellent hand-eye coordination. Ability to differentiate between colored wires, tabs, and electronic components. Must wear PPE, such as gloves, safety glasses, hard hat, and ear protection, while working on the production floor #LI-GB1 What you'll receive for the great work you provide: Full range of medical, dental, and vision plans Life Insurance Short-term and Long-term Disability Matching 401(k) Contributions Vacation and Paid Sick Time Tuition Reimbursement Pay Range (Applicable to California)$17.98 USD - $24.27 USD HourlyJob CategoryOperations Is Sponsorship Available? No Crown is an Equal Opportunity Employer and employment selection decisions are based on merit, qualifications, and abilities. We do not discriminate based on: age, race, religion, color, sex, national origin, marital status, sexual orientation, gender identity, veteran status, disability, pregnancy status, or any other status protected by law. We're happy to provide reasonable accommodations to those with a disability for assistance in the application process. Please email accessibility@flex.com and we'll discuss your specific situation and next steps (NOTE: this email does not accept or consider resumes or applications. This is only for disability assistance. To be considered for a position at Crown, you must complete the application process first).

Under minimal supervision, the Assembler III performs optical and mechanical assembly of high complexity requiring fitting, alignment and adjustment of components, units and assemblies to very close tolerances. Primary Duties & Responsibilities Clean and assemble various optical parts, mechanical subassemblies and large assemblies of high complexity. Requires the use of hand tools to perform a wide variety of electronic or electro-mechanical, mechanical or measurement product assembly operations on assemblies or sub-assemblies. Determines and/or follows methods and sequence of operations in performing wiring, component installation, hand soldering and cable harnessing, and fitting on assembly units. Solders onto various parts as required by assembly instructions. Primes and bonds optical surfaces to other optical or mechanical components. Reads detailed, complex blueprints, assembly sketches and procedures with very little supervision. Fits or adjusts parts or assemblies within established guidelines. Inspects and test finished items or assemblies. Education & Experience High School Diploma or (GED) 4 years of experience in similar assembly operation. High level of manual dexterity, Knowledge of an ability to use a wide variety of hand tools and knowledge of soldering. Soldering certification is required Basic computer navigation skills are required Experience with optical handling, inspection and gluing are highly desired Skills Mathematical Skills Ability to calculate figures and perform simple addition, subtraction, multiplication and division of whole numbers and fractions. Language Skills Ability to read and interpret documents such as safety rules, operating and maintenance instructions, procedure manuals and blueprints. Reasoning Ability Ability to apply common sense understanding to carry out instructions furnished in written, oral or diagram form. Ability to deal with problems involving several concrete variables in standardized situations. Working Conditions Job operates in production environment on 1st shift, Mon-Fri. Typically works in a lab environment with some time in an office near the work areas. Some work requires the use of hazardous chemicals. Noise level - Usually moderate Physical Requirements Standing. Particularly for sustained periods of time. Working with Hand / Fingers. Picking, pinching, typing or otherwise working, primarily with fingers rather than with the whole hand as in handling. Lifting. Raising objects from a lower to a higher position or moving objects horizontally from position-to-position. This factor is important if it occurs to a considerable degree and requires substantial use of upper extremities and back muscles. Safety Requirements All employees are required to follow the site EHS procedures and Coherent A&D EHS standards. Quality and Environmental Responsibilities Depending on location, this position may be responsible for the execution and maintenance of the ISO 9000, 9001, 14001 and/or other applicable standards that may apply to the relevant roles and responsibilities within the Quality Management System and Environmental Management System. Culture Commitment Ensure adherence to company's values (ICARE) in all aspects of your position at Coherent A&D: Integrity - Create an Environment of Trust Collaboration - Innovate Through the Sharing of Ideas Accountability - Own the Process and the Outcome Respect - Recognize the Value in Everyone Enthusiasm - Find a Sense of Purpose in Work Coherent A&D is an equal opportunity/affirmative action employer. All qualified applicants will receive consideration for employment without regard to sex, gender identity, sexual orientation, race, color, religion, national origin, disability, protected Veteran status, age, or any other characteristic protected by law. This role involves access to technology, materials, software, or hardware subject to U.S. export control laws. Therefore, to be considered, candidates must be classified as a “U.S. Person” under applicable regulations or be eligible for authorization under a U.S. government export license.

About the Company: DwyerOmega is a globally trusted leader in manufacturing innovative instrumentation solutions for the Process Measurement, Automation, Control and HVAC markets. With very strong brand recognition and high levels of customer loyalty, DwyerOmega has an unmatched reputation for providing customized solutions that meet and exceed customer needs. Our team of engineering experts help our customers select technical, and often configured, product solutions for their unique applications. The company offers over 300,000 state-of-the-art products for process measurement and control of temperature, humidity, pressure, strain, force, flow, level, pH, conductivity, and indoor air quality, and is a recognized global leader in the digital marketing of technical products. The products that we manufacture are used to control and drive process efficiency, creating safe and sustainable environments. At DwyerOmega, we enable our customers to improve the world - one measurement at a time. We achieve this through our unwavering commitment to technology, customer service, and overall continuous improvement. Every day, we strive to cultivate a culture of ingenuity, empowerment, accountability, adaptability, and speed. The company's corporate headquarters are based in Michigan City, Indiana, and Norwalk, CT with manufacturing locations and sales offices located throughout the world. Analytical Industries: Analytical Industries is a leading provider of advanced gas analysis and measurement solutions for industrial, medical, and environmental applications. We take pride in our engineering excellence, precision manufacturing, and commitment to helping customers achieve accurate, reliable process control. As part of the DwyerOmega family, we bring together decades of instrumentation expertise and customer-focused innovation. Position Summary: The Assembler is responsible for assembling, wiring, soldering, testing, and inspecting small electro-mechanical components used in sensor and analyzer products. This position requires close attention to detail, steady hands, and adherence to established quality and safety standards. Working under the direction of the Lead or Production Manager, the assembler follows detailed assembly instructions, performs accurate and repetitive work, and supports overall production efficiency. The role also includes maintaining a clean and organized work area and performing all other duties as assigned. Responsibilities include the following. Other duties may be assigned. Assemble electrochemical sensors and electromechanical analyzers, and related subcomponents according to engineering drawings, schematics, and work instructions. Perform wiring, soldering, and mechanical assembly using hand tools and electronic testing equipment. Log production results, nonconformities and test outcomes accurately in manufacturing documents such as the DHR. Inspect components before assembly for defects or non-conformance. Maintain a clean and organized work area in accordance with safety and 5S practices. Collaborate with engineering and quality teams to identify assembly issues and propose process improvements. Follow all company policies related to safety, quality assurance, and environmental compliance. Requirements Essential/Preferred Skills: 1-2 years of work experience in electro-mechanical assembly, preferably in sensor instrument manufacturing. High school diploma or GED equivalent. Ability to read and interpret drawings, schematics, and work instructions. Prior experience with hand tools. Strong attention to detail and commitment to product quality. Work Conditions and Physical Requirements: Work performed primarily in an office/manufacturing space. Frequent sitting, standing, bending, and using small tools. May involve handling chemicals used in assembly rooms. Use of PPE (gloves, safety glasses) as required. May require repetitive motions to maintain quality of sensor/analyzer products. Salary Description $18-$20

Under general supervision, the Final and pH Assembler performs final assembly of pH and ORP sensors, including the soldering of cable to pH sensors, soldering and installing connectors, and encapsulating connections with epoxies and silicones. Performs related functions as needed. Tasks (regardless of the current job holder) Core tasks: 1. Read and interpret manufacturing procedures, work instructions and prints. 2. Cut and strip cables using both hand tools and cut & strip machines. 3. Prepare labels with a heat shrink labeling machine and shrink onto cables. 4. Prepare cables for connection to sensors by tinning wires with a soldering iron. 5. Prepare cable ends with the installation of a BNC connector using the pneumatic crimp machine. 6. Install pin tips and various other connectors with the use of a hand crimper. Complementary tasks: 1. Mix 2 part epoxies using a scale in preparation for encapsulation. 2. Pot cables into the backseal of the sensor using epoxy dispensing equipment. Requirements for the position Education/Training: AA degree- Electronics. Experience/Certification: Two years of electronics or electro-mechanical assembly experience is required. Knowledge, Skills, and Abilities: • Knowledgge of pH sensor equipment and assembly and testing procedures. • Knowledge of safe production assembly practices. • Knowledge of soldering and de-soldering techniques. • Set up and use multimeter, picoammeter and measurement tools. • Set up and operate spectrophotometer, oscilloscope, and microscope. • Set up and operate pressure tester, hi-pot continuity tester, conductivity tester, and decade resistance tester. • Set up and operate soldering, and de-soldering equipment and heat gun. • Read and interpret blueprints, manufacturing procedures, and instructions. • Recognize proper color codes for different components in assembly process. • Complete daily work assignments within agreed upon time frame. • Requires ability to effectively read, speak and write in the English language to communicate, understand and follow written and verbal instructions Pay rate: $18.00-$20.00

Job Description Under general supervision, performs a wide variety of electromechanical or mechanical production sub-assembly and assembly operations to build up and assemble difficult and complex instruments. Duties may include following techniques to wire, prepare cable harnesses and install cable harnesses. Perform coating, mixing and cooking of raw materials to create finished products. Essential Job Functions Assembly Activities Under general supervision, performs various tasks requiring knowledge of assembly techniques, tools, materials, machines and equipment. Assembles electromechanical instruments or fabricated parts to make subassemblies or complete instruments using hand tools, power tools and special tools and/or calibration equipment. Determines methods and sequence of assembly operations where complete information is not readily available or follows assembly shop and production operations sheets, wire lists, samples, blue prints, schematics and verbal instructions to perform a wide variety of assembly operations. Fits, aligns, calibrates and adjusts parts and mechanisms to meet tolerances and product operating and quality requirements. Works from engineering drawings, rough sketches, and manuals, verbal or written instructions from Lead Assembler or Supervisor. Performs in-process and final quality inspection of assembled products. Examines drawings and work orders to determine the work that needs to be performed. Utilizes appropriate machines and tools to install, mount, fasten, align and adjust parts, components, wiring and harnesses. Evaluates assembly procedures and manuals and recommends revisions when required. Performs such tasks as replacing components and wiring circuits. Trains new hires and co-workers as necessary to enhance skill level and knowledge base. Examines and tests assembly at various stages of production to identify errors. Maintains a record of the assembly process, progress and problems. Provides feedback to supervisor when a deviation from accepted practice or safety issues are recognized. Utilizes small hand tools such as wire strippers, crimpers, wrenches, screwdrivers, pliers, and hammers. Identifies and selects components to be integrated into sub-assembly and assembly units. Makes own set-ups, alignments and adjustments maintaining tolerance in accordance with instructions. Disassembles, modifies, reworks, refurbishes, reassembles, and tests instruments as required. Clean and coat molds for fixtures and product used. Perform mixing and cooking of gels in a laboratory environment. Other Activities Evaluates and recommends changes in methods and procedures in assigned area of responsibility. Performs data entry on work-in-process transaction and parts ordering. Recommends and implements methods to promote teamwork and maintains a pleasant work environment within department and with other departments. Trains new team members on how to fill out DHR such as batch record and traveler during the production run. Seeks constant improvement in work processes and techniques. Assures that laboratory and assembly areas are in an orderly and functional condition. Suggests improvement in departmental work processes and procedures. Maintains good communications with peers, Lead Assembler and Supervisor. Attends and participates in group meetings, task force groups, etc., as needed. Works with Support Engineering to develop and maintain time standards. Aids Support Engineering with design of assemblies and units for manufacturing capability. Performs other duties and projects as assigned by Supervisor and/or Lead Assembler. Essential Job Requirements Education High school diploma, GED or equivalent education and experience. Experience & Minimum Qualifications 4-6 years of assembly experience in a fast-paced manufacturing environment Ability to follow schematics and assemble wire harnesses is a must. Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals, engineering prints and schematics. Ability to add, subtract, multiply and divide in all units of measure, using whole numbers, common fractions, and decimals using a calculator. Ability to compute rate, ratio and percent, and to draw and interpret bar graphs. Ability to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization exists. Ability to interpret a variety of instructions furnished in written, oral, diagram, or schedule form. Ability to use standard power hand tools and custom tools, gauges, and other calibration equipment and assembly fixtures. Ability to lift 25 to 50 pounds is an asset Strong organizational skills through demonstrated ability to multi-task and manage time Established collaboration skills and the ability to communicate with openness and transparency. Ability to comply with FDA Good Manufacturing Practices (GMP). Ability to meet production schedules and project deadlines. Exposure and training to Six Sigma and/or lean manufacturing preferred. Physical Requirements & Working Environment Ability to work safely and according to departmental procedures when working at high temperatures with hazardous equipment and materials such as oven, mixers, hot plates, ultrasonic cleaner, pressure cooker, fume hood, power tools, wire strippers, heat guns, heated cutting blades and others. Ability to work safely and according to departmental procedures when handling volatile chemicals which may or may not be hazardous. Ability to work safely in a chemical laboratory environment. Ability to occasionally lift and/or move up to 50 lbs. Ability to successfully respond to multiple work pressures. Ability to communicate verbally to individuals and groups. Ability to communicate verbally in person and using a phone. Ability to listen for understanding and assisting in problem solving. Ability to regularly use hands to utilize maximum dexterity. Ability to frequently to walk, stand, sit, and reach with hands and arms. Ability to occasionally to stoop, kneel, crouch, or crawl and hear. Specific vision abilities required include close vision, color vision, and ability to adjust focus. "Sakura Finetek USA, Inc. is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex including sexual orientation and gender identity, national origin, disability, protected Veteran Status, or any other characteristic protected by applicable federal, state, or local law.” The above description identifies the essential job functions and skills needed by the person or persons assigned to this position. These job functions and skills are not intended to be a complete and exhaustive list of all responsibilities, duties and skills required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential job functions. The information contained herein is subject to change at the company's discretion.

Temp To Full-Time Skillset Group is seeking a Wire Harness Assembler to work in the Irvine, CA area. This position will under shop supervision the Inspect and perform work in accordance with IPC-A610 and other quality standards as needed. This will be a 1st shift position and will be contract to hire. To apply email: *************************

The Optical Assembly Technician is responsible for the precise assembly, alignment, and testing of optical components and systems. This position requires a strong attention to detail, excellent manual dexterity, and the ability to work with microscopes and fine tools in a lab environment. The technician will follow technical drawings, and work instructions to ensure product quality and performance standards are met. Primary Duties & Responsibilities * Assemble optical components (lenses, mirrors, prisms, filters) into mechanical housings using specialized tools and adhesives. * Perform precision alignment of optical assemblies using alignment fixtures and laser alignment systems. * Inspect optical components for defects such as scratches, chips, and coating flaws using microscopes and interferometers. * Handle and clean optics using industry-standard procedures (e.g., use of IPA, lint-free wipes, static control tools). * Read and interpret engineering drawings, work orders, and process instructions. * Conduct performance tests on finished assemblies using optical testing equipment. * Record test results and maintain accurate production and quality documentation. * Collaborate with engineering and quality assurance teams to resolve issues and improve processes. * Maintain a clean and organized work area, following all contamination control protocols. * Follow safety and ESD (electrostatic discharge) guidelines at all times. Education & Experience * High school diploma or equivalent; technical certificate or associate degree in optics, electronics, or related field preferred * Minimum of 2 years of experience in optical or precision assembly, or relevant hands-on technical experience Skills * Proficiency using microscopes, tweezers, torque drivers, and other fine assembly tools * Strong hand-eye coordination and manual dexterity * Ability to follow detailed work instructions and technical drawings * Basic computer skills for data entry and documentation * Preferred Skills * Experience working in a cleanroom or controlled environment * Familiarity with ISO standards and quality systems * Knowledge of laser safety and optical coatings Working Conditions * Work is performed in a lab environment with strict contamination controls * * May require use of PPE such as gloves, cleanroom attire, and safety glasses Physical Requirements * Requires sitting or standing for extended periods and working with small parts. Safety Requirements All employees are required to follow the site EHS procedures and Coherent A&D EHS standards. Quality and Environmental Responsibilities Depending on location, this position may be responsible for the execution and maintenance of the ISO 9000, 9001, 14001 and/or other applicable standards that may apply to the relevant roles and responsibilities within the Quality Management System and Environmental Management System. Culture Commitment Ensure adherence to company's values (ICARE) in all aspects of your position at Coherent A&D: Integrity - Create an Environment of Trust Collaboration - Innovate Through the Sharing of Ideas Accountability - Own the Process and the Outcome Respect - Recognize the Value in Everyone Enthusiasm - Find a Sense of Purpose in Work Coherent A&D is an equal opportunity/affirmative action employer. All qualified applicants will receive consideration for employment without regard to sex, gender identity, sexual orientation, race, color, religion, national origin, disability, protected Veteran status, age, or any other characteristic protected by law. This role involves access to technology, materials, software, or hardware subject to U.S. export control laws. Therefore, to be considered, candidates must be classified as a "U.S. Person" under applicable regulations or be eligible for authorization under a U.S. government export license. If you need assistance or an accommodation due to a disability, you may contact us at ******************************.